Toshiba VF-S11 manual Contents of the product, Installation

Page 10

E6581160

1.2Contents of the product

Explanation of the name plate label. Always shut power off first then check the ratings label of inverter held in a cabinet.

Type

Form

1

V F S 11 S - 2 0 0 7 P L E - W N - A 2 2

Model name

TOSVERT VF-S11series

Number of power phases

S:single-phase None:

three-phase

Input (AC) voltage

2 : 200V to 240V

4 : 380V to 500V

6 : 525V to 600V

Applicable motor

capacity

002 : 0.2kW

004 : 0.4kW

005 : 0.55kW

007 : 0.75kW

015 : 1.5kW

022 : 2.2kW

037 : 3.7kW

055 : 5.5kW

075 : 7.5kW

110 : 11kW

150 : 15kW


Additional functions I					Default interface
Additional functions I						logic*
						logic*

None: No filter inside					WN, AN: Negative
M: Built-in basic filter					WN, AN: Negative
M: Built-in basic filter					WP	: Positive
L: Built-in					WP	: Positive
high-attenuation
high-attenuation
EMI filter

Operation panel				Additional function II

P: Provided				None: Standard product
P: Provided				E: Enclosed type
				U: Open type
				R: With a built-in RS-485
				circuit board

Special specification code

A:is the number

*This code represents the factory default logic setting. You can switch from one input/output logic to the other using slide switch SW1.

1.3Installation

Install the inverter in a well-ventilated indoor place and mount it on a flat metal plate in portrait orientation.

If you are installing more than one inverter, the separation between inverters should be at least 5 centimeters, and they should be arranged in horizontal rows. If the inverters are horizontally arranged with no space between them (side-by-side installation), peel off the ventilation seals on top of the inverter. It is necessary to decrease the current if the inverter is operated at over 50°C.

•Standard installation

•Side-by-side installation

5 cm or more

10 cm or more

VFS11	5 cm or more

10 cm or more

VFS11 VFS11 VFS11

Remove seals on top

10 cm or more

10 cm or more

The space shown in the diagram is the minimum allowable space. Because air cooled equipment has cooling fans built in on the top or bottom surfaces, make the space on top and bottom as large as possible to allow for air passage.

Note: Do not install in any location where there is high humidity or high temperatures and where there are large amounts of dust, metallic fragments and oil mist.

9

Image 10

Contents For 3-phase induction motors Industrial InverterSafety precautions Safety precautionsMeanings of symbols Explanation of markingsGeneral Operation Transportation & installation WiringOperations When retry function is selected inverter Maintenance and inspection Contents  Read first Check product purchaseCD-ROM E6581167 Contents of the product InstallationStandard connections Standard connection diagramConnection VF-S11FLA FLCFLB PLC OUTPower circuit Power circuit terminalsSelection of wiring materials Description of terminalsControl circuit terminals 24VDC PLC Control circuit terminalsSW1 VIAPTC FLB FLARY RC Slide switch SW1PLC Source Positive logic SW1 Source PLC Sink Eoqf OperationsSimplified Operation of the VF-S11 HoqfCoast stop How to start and stopStart and stop using the operation panel keys EOQF= HOQF= How to set the frequencyExample of operating a run from the panel Setting the frequency using the operation panel HOQF= or Frequency settingHow to operate the VF-S11 Running and stopping using the operation panelEx.2 Running and stopping using external signals Ex.3VIA Panel jog mode Status monitor mode Mode for monitoring all inverter statusBasic VF-S11 operations Standard monitor mode Flow of status monitor modePast trip record detained monitor mode When you adjust the inverter repeatedly using How to set parametersParameters for detailed and special setting. See Same parameter. Parameter name CWJ. See How to set the basic parameters⇔HJ How to set extended parameters～H Example of parameter setting Search and resetting of changed parameters I4WHow to search and reprogram parameters ⇔ CEE Parameters that cannot be changed while running How to use the history function⇔CEE How to save/load the user setting parameters Returning all parameters to standard default settingKpkv Monitoring the operation status Status monitor modeStatus monitor under normal conditions Iiii Pgtt ⇔ Display of detailed information on a past trip Display of trip information at the occurrence of a trip Display of trip informationTrip code display Example of call-up of trip informationOFF VIA VIB RES QR ⇔Cumulative E6581160 Measures to satisfy the standards How to cope with the CE directiveAbout the EMC directive Measures to satisfy the EMC directive Three-phase 500V class Example of wiring About the low-voltage directiveMeasures to satisfy the low-voltage directive Compliance with InstallationCompliance with UL Standard and CSA Standard Compliance with ConnectionAIC a AIC, Fuse and Wire sizesMotor thermal protection AWGBasic parameters Table of parameters and dataUser parameters Four navigation functionsCEE QNO Extended parameters Input/output parametersFrequency parameters Operation mode parameters Torque boost parameters Acceleration/deceleration time parameters Protection parameters Output parameters Operation panel parametersCommunication parameters PM motor parameters Default settings by inverter rating XD／H Table of input terminal functions AD2+SS3+AD2 , H, H, HTable of output terminal functions AD3On QE-,QR-,QJ, ,QJ,WR,GH,WE,QN-,QNT Fcvibn Models and their standard specifications SpecificationsStandard specifications Common specification CharacteristicsSpecification Outside dimensions and mass Outside dimensions and massOutline drawing VF-S11Fig.D Before making a service call Trip information and remedies Trip causes/warnings and remediesQNT Industrial and Power Systems & Services Company