Shindaiwa AHS2510/EVC manual Starting the Engine, When the Engine Starts

Page 10

Starting the Engine

IMPORTANT!

Engine ignition is controlled by a two position switch mounted on the throttle housing labeled, “I” for ON or START and “O” for OFF or STOP.

WARNING!

Never start the engine from the operating position.

1.Slide the ignition switch to the “ON” position.

2.Set the throttle lever to the “fast idle”:

a.Squeeze the throttle lever toward the handgrip on the shaft tube.

b.Depress and hold the throttle lock button.

c.While depressing the throttle lock button, release the throttle lever.

3.Press the primer bulb until fuel can be seen flowing in the transparent return tube.

IMPORTANT!

The primer system only pushes fuel through the carburetor. Repeatedly press- ing the primer bulb will not flood the engine with fuel.

4.Set the choke lever to the CLOSED position if engine is cold.

5.While holding the outer tube firmly with left hand. Use your other hand to slowly pull the recoil starter handle until resistance is felt, then pull quickly to start the engine.

CAUTION!

Do not pull the recoil starter to the end of the rope travel. Pulling the recoil starter to the end of the rope travel can damage the starter.

WARNING!

The cutting attachment may move when the engine is started!

When the Engine Starts...

ON

Throttle Lock

Button

Slide ignition to ON

Close choke

6HWWKHFKRNHOHYHUWRWKH&/26('SRVLWLRQ

6.When the engine starts, slowly move the choke lever to the “OPEN” posi- tion. (If the engine stops after the initial start, close the choke and restart.)

7.Operating the throttle will automatically disengage the fast idle setting.

IMPORTANT!

If the engine fails to start after several attempts with the choke in the closed position, the engine may be flooded with fuel. If flooding is suspected, refer to the ”Starting a Flooded Engine” section of this manual.

Primer Bulb

Return Tube

3UHVVSULPHU

bulb...

Hold

the unit ¿UPO\

...and pull recoil

Make sure the

attachment is clear

starter handle

of obstructions!

upward

 

Open

$IWHUHQJLQHVWDUWVPRYHFKRNHWR23(1

SRVLWLRQ

ŶAfter the engine starts, allow the engine to warm up at idle 2 or 3 min- utes before operating the unit.

ŶAfter the engine is warm, pick up the unit and clip on the shoulder strap, if so equipped.

ŶAdvancing the throttle makes the cutting attachment move faster; releasing the throttle permits the attachment to stop moving. If the cutting attachment con-

tinues to move when the engine returns to idle, carburetor idle speed should be adjusted (see “Adjusting Engine Idle”.).

10

Image 10
Contents AHS2510/EVC Articulated Hedge Trimmer English Español .... SP1 Français ... FR1Safety and operation labels ContentsIntroduction Operating Precautions SafetyArticulated Safety Equipment and Labels Operator SafetyProduct Description 6SHFLÀFDWLRQVConnect the Powerhead/Outer Tube to the Gearcase AssemblyPrior To Assembly HandleAdjusting the Hedge Trimmer Cutter Assembly Travel limiter and adjustment rangeWith the engine off, install the scab- bard onto the blade Adjusting cutter assembly for storage or transportationThrottle lever free play Examples of 501 mixing quantities Mixing fuelFilling the fuel tank Minimize the Risk of FireStarting the Engine When the Engine StartsDepress and hold the throttle lock button Stopping the Engine Adjusting Engine IdleIdle Speed Adjustment Checking Unit ConditionSafe Operation OperationChecking Unit Condition Before trimmingMaintenance Remove and clean or replace the spark plug Hour maintenance10/15-Hour maintenance Direct the air stream at the inside face of the filter onlyRemove and replace the fuel filter element Cutter blade adjustment 139/150-Hour MaintenanceValve Adjustment Maintenance after first 139-hoursLong Term Storage 0XIÁHUDQGVSDUNDUUHVWHU DlqwhqdqfhWhat To Check Troubleshooting GuideEngine does not Start RemedyIs the engine overheating? LOW PowerPossible Cause Engine is knockingAdditional Problems What To Check Possible Cause RemedyEmission System Warranty Statement NOTAs Remarques 731-3167, Japan Cortasetos Articulado AHS2510/EVC ¡ADVERTENCIADeclaraciones De Seguridad IntroducciónEtiquetas de seguridad Seguridad Precauciones de utilizaciónEtiquetas de seguridad Seguridad continuaciónFuncionamiento Descripción del Producto Montaje del bloque MotorAntes de Ensamblar EnsamblarMango Ajuste del conjunto de la cuchilla del cortasetos Ensamblar continuaciónLimitador de desplazamiento y gamo de ajuste Afloje la tuerca de seguridad en el cable ajustador Ajustando para almacenaje o transportaciónAjuste la holgura del acelerador Apriete la tuerca de seguridadPrecaución Mezcla de CombustibleLlenando el Tanque de Combustible AdvertenciaArranque del motor Al arrancar el motorDeslice el interruptor de ignición a la Posición O motor ApagadoOperación segura Aplicaciones9HULÀTXHODFRQGLFLyQGHODXQLGDG Antes de recortarMantenimiento Mantenimiento cada 10 horas Mantenimiento continuaciónMantenimiento cada 10 o 15 horas Retire y reemplace el elemento del filtro Mantenimiento cada 50 horasCon más frecuencia en condiciones de polvo o suciedad Afloje el perno de fijación de la caja de engranajesAjuste de válvulas Mantenimiento Cada 139/150 HorasAjuste de las cuchillas de corte Retire la malla y limpie con un cepillo de cerdas gruesas Almacenamiento de Largo PlazoMantenimiento de la silenciador Repita los pasos 1 y 2 hasta que el motor ya no arranqueQué revisar Guía DiagnósticoEL Motor no Arranca Posible causaLimpiar, reparar o sustituir en caso necesario Baja Potencia¿Se sobrecalienta el motor? El motor golpeaGuía Diagnóstico continuación Cobertura de la Garantía del Fabricante Esta garantía es administrada porSus Derechos y Obligaciones de Garantía Que Está Cubierto Por Esta GarantíaSP22 SP23 Tualatin, Oregon 97062 USA 11, Ozuka-Nishi TAILLE-HAIE Articulé AHS2510/EVC AvertissementMise EN Garde Table des matièresMises en garde RemarqueSécurité Consignes d’utilisationÉtiquettes et dispositifs de sécurité Sécurité suiteSécurité d’opérateur Nomenclature Caractéristiques techniquesPoignée AssemblageAvant l’assemblage Assemblage moteur/tube de transmissionRéglage de l’accessoire de coupe et limiteur de déplacement Réglage de l’accessoire de coupe du taille-haieAssemblage suite Position de remisage/transport Réglage de la course libre du levier d’accélérationExemples de quantités de mélange de carburant à Mélange de carburantRemplissage du réservoir à carburant Réduire les risques d’incendieDémarrage du moteur Lorsque le moteur démarreRéglage du ralenti du moteur Démarrage du moteur suiteArrêt du moteur Contrôle de l’état de l’appareilAvant de découpe FonctionnementUtilisation sûre Position de travailEntretien Entretien aux 10 heures Entretien suiteEntretien aux 10 à 15 heures Plus souvent dans des conditions poussiéreuses ou sales Remplacement du filtre à carburantEntretien aux 50 heures Santes du système d’alimentation en carRéglage du jeu des soupapes Réglage de la lame de l’accessoire de coupeEntretien aux 139 heures Remplacer la bougie sur une baseRemisage à long terme Entretien du silencieuxLE Moteur NE Démarre PAS SolutionGuide de dépannage Points à contrôlerLe moteur surchauffe-t-il ? Guide de dépannage suitePuissance Insuffisante Le moteur cognePoints à contrôler Cause probable Solution Autres ProblèmesCouverture de la garantie des fabricants La présente garantie est administrée parVos droits et obligations en vertu de la garantie Couverture de la garantieFR22 FR23