Shindaiwa AHS2510/EVC manual Maintenance

Page 13

Maintenance

General maintenancel

IMPORTANT!

MAINTENANCE, REPLACEMENT OR REPAIR OF EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PER- FORMED BY ANY REPAIR ESTABLISH- MENT OR INDIVIDUAL; HOWEVER, WAR- RANTY REPAIRS MUST BE PERFORMED BY A DEALER OR SERVICE CENTER AUTHORIZED BY SHINDAIWA INC. THE USE OF PARTS THAT ARE NOT EQUIVA- LENT IN PERFORMANCE AND DURA- BILITY TO AUTHORIZED PARTS MAY IMPAIR THE EFFECTIVENESS OF THE EMISSION CONTROL SYSTEM AND MAY HAVE A BEARING ON THE OUTCOME OF A WARRANTY CLAIM.

NOTE:

Using non-standard replacement parts could invalidate your Shindaiwa warranty.

WARNING!

Before performing any mainte- nance, repair, or cleaning work on the unit, make sure the engine and cutting attachment are completely stopped.

Disconnect the spark plug wire before performing service or maintenance.

0XIÁHU

This unit must never be operated with a faulty or missing spark arrester or muf- fler. Make sure the muffler is well secured and in good condition. A worn or damaged muffler is a fire hazard and may also cause hearing loss.

Spark Plug

Keep the spark plug and wire connections tight and clean.

Fasteners

Make sure nuts, bolts, and screws (except carburetor adjusting screws) are tight.

WARNING!

Non-standard accessories, cut- ting attachment, or replacement parts may not operate properly with your unit and may cause damage and lead to personal injury.

Air Filter

The C4 engine that powers your Shindaiwa model is a hybrid 4-stroke engine. As a hybrid, the engine is lubricated by oil mixed with the gasoline and air from the carburetor that moves through and around the internal parts of the engine in a similar way that a

2-stroke engine is lubricated. Without the heavy duty 2-stage air filter equipped on all C4 engines, dust and dirt could also move through the engine, decreasing engine life, increasing valve wear and the need for more frequent valve adjustments. To keep your C4 engine strong and reliable, Shindaiwa recommends that you check and service the air filter as instructed in the 10-Hour Mainte- nance section that follows.

Daily maintenance

Prior to each work day, perform the following:

ŶRemove all dirt and debris from the engine, check the cooling fins and air cleaner for clogging, and clean as necessary.

ŶCarefully remove any accumulations of dirt or debris from the muffler and fuel tank. Check cooling air intake area at base of crankcase. Remove all debris. Dirt build-up in these areas can lead to engine overheating, fire, or premature wear.

WARNING!

Always wear gloves when working around the cutter assembly.

ŶLubricate the blades before use and after refueling. Check the cutters for damage or incorrect adjustment.

ŶClean any debris or dirt from the cut- ting attachment.

Cooling

¿QV

Cooling

¿QV

Air

intake

5HPRYHDOOGLUWDQGGHEULVIURPWKHHQJLQHDQGFKHFNWKHFRROLQJ¿QV

Ŷ Check for loose or missing screws or

Ŷ Make sure nuts, bolts, and screws

components. Make sure the cutter

(except carburetor idle speed adjusting

attachment is securely fastened.

screws) are tight.

Ŷ Check the entire unit for leaking fuel

 

or grease.

 

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents English Español .... SP1 Français ... FR1 AHS2510/EVC Articulated Hedge TrimmerSafety and operation labels ContentsIntroduction Operating Precautions SafetyArticulated Operator Safety Safety Equipment and Labels6SHFLÀFDWLRQV Product DescriptionPrior To Assembly AssemblyConnect the Powerhead/Outer Tube to the Gearcase HandleTravel limiter and adjustment range Adjusting the Hedge Trimmer Cutter AssemblyWith the engine off, install the scab- bard onto the blade Adjusting cutter assembly for storage or transportationThrottle lever free play Filling the fuel tank Mixing fuelExamples of 501 mixing quantities Minimize the Risk of FireStarting the Engine When the Engine StartsDepress and hold the throttle lock button Idle Speed Adjustment Adjusting Engine IdleStopping the Engine Checking Unit ConditionChecking Unit Condition OperationSafe Operation Before trimmingMaintenance 10/15-Hour maintenance Hour maintenanceRemove and clean or replace the spark plug Direct the air stream at the inside face of the filter onlyRemove and replace the fuel filter element Valve Adjustment 139/150-Hour MaintenanceCutter blade adjustment Maintenance after first 139-hours0XIÁHUDQGVSDUNDUUHVWHU Dlqwhqdqfh Long Term StorageEngine does not Start Troubleshooting GuideWhat To Check RemedyPossible Cause LOW PowerIs the engine overheating? Engine is knockingWhat To Check Possible Cause Remedy Additional ProblemsEmission System Warranty Statement NOTAs Remarques 731-3167, Japan ¡ADVERTENCIA Cortasetos Articulado AHS2510/EVCDeclaraciones De Seguridad IntroducciónEtiquetas de seguridad Precauciones de utilización SeguridadEtiquetas de seguridad Seguridad continuaciónFuncionamiento Montaje del bloque Motor Descripción del ProductoAntes de Ensamblar EnsamblarMango Ajuste del conjunto de la cuchilla del cortasetos Ensamblar continuaciónLimitador de desplazamiento y gamo de ajuste Ajuste la holgura del acelerador Ajustando para almacenaje o transportaciónAfloje la tuerca de seguridad en el cable ajustador Apriete la tuerca de seguridadLlenando el Tanque de Combustible Mezcla de CombustiblePrecaución AdvertenciaAl arrancar el motor Arranque del motorPosición O motor Apagado Deslice el interruptor de ignición a la9HULÀTXHODFRQGLFLyQGHODXQLGDG AplicacionesOperación segura Antes de recortarMantenimiento Mantenimiento cada 10 horas Mantenimiento continuaciónMantenimiento cada 10 o 15 horas Con más frecuencia en condiciones de polvo o suciedad Mantenimiento cada 50 horasRetire y reemplace el elemento del filtro Afloje el perno de fijación de la caja de engranajesAjuste de válvulas Mantenimiento Cada 139/150 HorasAjuste de las cuchillas de corte Mantenimiento de la silenciador Almacenamiento de Largo PlazoRetire la malla y limpie con un cepillo de cerdas gruesas Repita los pasos 1 y 2 hasta que el motor ya no arranqueEL Motor no Arranca Guía DiagnósticoQué revisar Posible causa¿Se sobrecalienta el motor? Baja PotenciaLimpiar, reparar o sustituir en caso necesario El motor golpeaGuía Diagnóstico continuación Sus Derechos y Obligaciones de Garantía Esta garantía es administrada porCobertura de la Garantía del Fabricante Que Está Cubierto Por Esta GarantíaSP22 SP23 Tualatin, Oregon 97062 USA 11, Ozuka-Nishi Avertissement TAILLE-HAIE Articulé AHS2510/EVCMises en garde Table des matièresMise EN Garde RemarqueConsignes d’utilisation SécuritéÉtiquettes et dispositifs de sécurité Sécurité suiteSécurité d’opérateur Caractéristiques techniques NomenclatureAvant l’assemblage AssemblagePoignée Assemblage moteur/tube de transmissionRéglage de l’accessoire de coupe et limiteur de déplacement Réglage de l’accessoire de coupe du taille-haieAssemblage suite Réglage de la course libre du levier d’accélération Position de remisage/transportRemplissage du réservoir à carburant Mélange de carburantExemples de quantités de mélange de carburant à Réduire les risques d’incendieLorsque le moteur démarre Démarrage du moteurArrêt du moteur Démarrage du moteur suiteRéglage du ralenti du moteur Contrôle de l’état de l’appareilUtilisation sûre FonctionnementAvant de découpe Position de travailEntretien Entretien aux 10 heures Entretien suiteEntretien aux 10 à 15 heures Entretien aux 50 heures Remplacement du filtre à carburantPlus souvent dans des conditions poussiéreuses ou sales Santes du système d’alimentation en carEntretien aux 139 heures Réglage de la lame de l’accessoire de coupeRéglage du jeu des soupapes Remplacer la bougie sur une baseEntretien du silencieux Remisage à long termeGuide de dépannage SolutionLE Moteur NE Démarre PAS Points à contrôlerPuissance Insuffisante Guide de dépannage suiteLe moteur surchauffe-t-il ? Le moteur cogneAutres Problèmes Points à contrôler Cause probable SolutionVos droits et obligations en vertu de la garantie La présente garantie est administrée parCouverture de la garantie des fabricants Couverture de la garantieFR22 FR23
Top Page Image Contents