Desa 100271-01 Felling Procedure, Limbing a Tree, Felling Notch, Felling Cut, Cut towards notch

Page 13

OWNER’S MANUAL

OPERATING CHAIN SAW

Continued

FELLING PROCEDURE

Felling Notch

A properly placed felling notch will deter- mine direction tree will fall. Place felling notch on side of tree in direction you want tree to fall (see Figure 13). Follow direc- tions below to create a felling notch.

1.Make lower notch cut as close to ground as possible. Hold saw so guide bar is horizontal. Cut 1/3 the diameter of tree trunk (see Figure 13). Note: Al- ways make this horizontal lower notch cut first. If you make this cut second, tree can pinch chain or guide bar.

2.Start upper notch cut the same distance above first cut as first cut is deep.

Example: If lower notch cut is 20 cen- timeters deep, start upper notch cut 20 centimeters above it. Cut downward at 45° angle. The upper notch cut should meet end of lower notch cut (see Fig- ure 13).

3.Remove tree trunk wedge created by notching cuts.

Felling Cut

1.Make felling cut five centimeters higher than lower notch cut and on opposite side of tree (see Figure 13). Keep fell- ing cut parallel to lower notch cut.

2.Cut towards notch.

WARNING: Do not cut all the way through tree. Leave about five centimeters of tree diameter uncut directly behind felling notch (see Figure 13). This uncut portion acts as a hinge. The hinge helps keep tree from twisting and falling in wrong direction.

3.As felling cut nears hinge, tree should begin to fall. Note: If needed, drive wedges into felling cut to control di- rection of fall. If tree settles back and pinches chain, drive wedges into fell- ing cut to remove saw. Only use wedges made of wood, plastic, or aluminum.

Never use wedge made of steel. This could cause kickback and damage to chain.

4.When tree begins to fall, quickly

•remove saw from felling cut

•release trigger to turn saw off

•put saw down

•exit area using retreat path

 

Direction of Fall

3rd Cut -

Hinge

Felling Cut

2nd Cut -

 

 

Upper

5 cm

Notch

Cut

5 cm

1st Cut -

 

Lower

 

Notch

 

Cut

Figure 13 - Felling A Tree

WARNING: Be alert for falling overhead limbs. Watch your foot- ing while exiting area.

LIMBING A TREE

WARNING: Avoid kickback. Kickback can result in severe in- jury or death. SeeKickback, pages 3 and 4, to avoid risk of kickback.

WARNING: When cutting limb that is under tension, use extreme caution. Be alert for wood spring- ing back. When wood tension is released, limb could spring back and strike operator causing se- vere injury or death.

CAUTION: Seek professional help if facing conditions beyond your ability.

Limbing is removing branches from a fallen tree. Make sure your footing is firm. Keep feet apart. Divide your weight evenly on both feet. Do not remove larger limbs under tree that support log off ground. Remove each limb with one cut (see Figure 14). Clear cut limbs from work area often. This will help maintain a safe work area.

Make sure you start your cut where limb will not pinch saw during cutting. To avoid pinching, start cut on freely hanging limbs from above limb. Start cut on limbs under tension from under limb. If pinch occurs, turn saw off, lift limb, and remove saw.

Figure 14 - Limbing A Tree

Continued

102891

11

Page 12 Page 14
Image 13
Page 12 Page 14
Contents MODEL/MODELL/MODÈLE 100271-01230V~ 50Hz 1450W 102891 Electric Chain SAW Safety Information Warnings Appears Throughout This Manual Information SymbolsKickback Safety Devices On This Saw SafetyBefore Operating Chain SAW KickbackSecure wood you are cutting by using clamps or chocks Saw Maintenance and Kickback SafetyPushback and PULL-IN Chain SAW OperationChain SAW Names and Terms Maintenance and Storage of Chain SAWRear Handle Handle located at rear of saw body Reduced Kickback Guide Bar GuideImportant Do not clamp chain saw in vise during assembly AssemblyProduct Identification UnpackingAssembling Guide Bar, Chain, and Hand Guard Filling OIL TankOperating Chain SAW SAW Chain Tension AdjustmentExtension Cords Chain Brake Oiling ChainCutting with the Chain SAW Before Felling a Tree Trimming a Tree PruningLimbing a Tree Felling ProcedureFelling Notch Felling CutCleaning SAW Body Cleaning and MaintenanceBucking a LOG Care of Guide BAR Normal Guide Bar MaintenanceSharpening Your SAW Chain Items Needed to Sharpen ChainRecycling Replacement PartsStorage Observed Fault Possible Cause Remedy TroubleshootingImporter Manufacturer Desa Europe B.V Warranty InformationElektrische Kettingzaag Gebruikershandleiding Elektrische Kettingzaag Betekenis SymbolenAlvorens DE Kettingzaag TE Gebruiken WAARSCHUWIN- GENTerugslag Veiligheidsvoorzieningen tegen terugslagMET DE Kettingzaag Werken Duwen EN TrekkenKettingzaagonderhoud en terugslagveiligheid Oorzaken van duwen en trekkenBreng de beschermkap aan DE Kettingzaag Onderhouden EN OpbergenUitpakken Benamingen EN TermenMontage Identificatie VAN OnderdelenDE Spanning VAN DE Ketting BIJ- Stellen Olie BijvullenNing van de ketting bij te stellen Verlengsnoeren DE Kettingzaag BedienenDE Ketting Olien DE Kettingrem ZagenEEN Boom Snoeien Veltechniek EEN Boom OmzagenAlvorens een boom om te zagen ValkerfEEN Stam in Stukken Zagen Takken VerwijderenDE Behuizing Schoonmaken Schoonmaak EN OnderhoudDe stam ligt over de gehele lengte op de grond De stam is aan één uiteinde ondersteundDE Ketting Slijpen Zorg Voor DE KettinggeleiderNormaal onderhoud van de kettinggeleider Gereedschap benodigd voor het slijpen van de kettingDe ketting vervangen De dieptebegrenzers van de snijtanden vijlenVERVANGINGS- Onderdelen DE Kettingzaag OpbergenWaarschuwing Gebruik uitsluitend in deze handleiding Onderdeelnummer OmschrijvingPagina Problemen OplossenDe olietank leeglopen wanneer de zaag Langere tijd niet gebruikt wordtImporteur Fabrikant Desa Europe B.V Beperkte Garantie Elektrische KettingzaagModèle 100271-01 230V~ 50Hz 145a0W Lire le manuel d’instructions Description SymbolesAvant D’UTILISER LA Tronçonneuse Avertissements Pour LA SécuritéRecul Cause du reculUtilisation DE LA Tronçonneuse Poussée ET TractionEntretien de la tronçonneuse et protection contre le recul Causes de la poussée et de la tractionEntretien ET Remisage DE LA Tronçonneuse Vocabulaire DE LA TronçonneuseDans un endroit sec Tronçonneuse électrique Nomenclature DES PiècesAssemblage DéballageRéglage DE LA Tension DE LA Chaîne Remplissage DU Réservoir D’HUILEUtilisation DE LA Tronçonneuse Rallonges DE CordonSciage Avec LA Tronçonneuse Lubrification DE LA ChaîneFrein DE Chaîne Avant d’abattre un arbre Abattage D’UN ArbreÉbranchage Procédure D’ABATTAGESifflet d’abattage Trait d’abattageToute la bille repose au sol Tronçonnage D’UNE BilleLa bille est soutenue à une extrémité La bille est soutenue aux deux extrémitésNettoyage DU Carter DE LA Tronçonneuse Nettoyage ET EntretienEntretien DE LA LAME- Guide Affûtage DE LA ChaîneAffûtage des taillants Remplacement de la chaîneLimage des limiteurs de profondeur des taillants Remisage RecyclagePièces DE Rechange Remiser la chaîneDépannage Instructions D’UTILISATION Importateur Fabricant Desa Europe B.V Information SUR LA GarantieModell 100271-01230V~ 50Hz 1450W Erklärung Zeichen ElektrokettensägeVOR Gebrauch DER Motorsäge SICHERHEITS- HinweiseRückprall Rückprall- Sicherheitsvorrichtungen an dieser SägeBetriebssicherheit STOSS- UND ReisskräfteWartung der Säge und Rückprallsicherheit Die Ursache von Stoß- und ReißkräftenWarten UND Lagern DER Motorsäge DIE Teile DER Motorsäge BEGRIFF- SerklärungenVorderer Handgriff Befindet sich am vor- deren Sägenrumpf Zusammenbau AuspackenEinstellen DER SÄGEKETTEN- Spannung Füllen DES ÖlbehältersVerlängerungskabel Gebrauch DER MotorsägeÖlen DER Kette SägeanleitungFällen Eines Baums KettenbremseVom Baum aus Vor dem Fällen eines Baums FällanleitungFallkerb FällschnittAblängen Entasten Eines BaumsStamm liegt der Länge nach auf dem Boden Stamm an einem Ende aufgebocktReinigen DES Sägenrumpfes Reinigung UND WartungPflege DES Schwertes Routinewartung DES SchwertesZum Schärfen der Kette benötigtes Werkzeug Schärfen DER SägeketteSchärfen der Schneidezähne Lagerung Wiederver WertungErsatzteile Säge schneidet nur unter starkem Druck Kette ist stumpf StörungssucheÖl ist zu zähflüssig Öl mit einer geeigneten Viskosität ver Schwert und Kette nicht richtig zusamNotizen Bitte GUT Aufbewahren GarantieBefristete Garantie Importeur Hersteller102891 Desa Europe B.V

100271-01 specifications

Desa 100271-01 is an innovative and efficient solution designed to enhance agricultural practices. Targeted primarily at small to medium-sized farms, this technology integrates advanced features that optimize farming processes, ultimately improving yield and reducing operational costs.

One of the standout features of Desa 100271-01 is its precision agriculture capability. Utilizing GPS and IoT (Internet of Things) technologies, the system enables farmers to manage their fields more effectively. The GPS technology ensures accurate field mapping, allowing for more efficient planting patterns and resource distribution. By monitoring crop health through real-time data collection, farmers can make informed decisions regarding watering, fertilization, and pest control, leading to healthier crops and minimized waste.

The platform is designed with user-friendliness in mind. Its intuitive interface allows farmers of varying technical backgrounds to navigate the system easily. Training is often included as part of the purchase, ensuring that users can maximize the potential of the Desa 100271-01 right from the start. Additionally, compatibility with mobile devices enables farmers to access information and controls from the field, enhancing operational flexibility.

Another notable characteristic is its sustainability focus. The Desa 100271-01 promotes eco-friendly agricultural practices by providing data-driven insights that help reduce water and fertilizer usage. This not only contributes to lower operational costs but also supports environmental conservation efforts.

In terms of connectivity, Desa 100271-01 employs robust wireless technologies to facilitate communication between various devices on the farm. This interconnectivity allows for real-time monitoring and control of agricultural equipment, leading to enhanced efficiency. The system can be integrated with existing farm machinery, making it a versatile addition to any agricultural setup.

Furthermore, the Desa 100271-01 is designed to withstand challenging agricultural environments. Its durable construction and weather-resistant features ensure reliable performance, even in adverse conditions.

Overall, Desa 100271-01 represents a significant advancement in agricultural technology. With its precision farming capabilities, user-friendly interface, sustainability initiatives, and robust connectivity, it stands out as a valuable asset for modern agricultural practices, contributing to increased efficiency and profitability for farmers.
Top Page Image Contents