Desa 100271-01 owner manual Cleaning and Maintenance, Bucking a LOG, Cleaning SAW Body

Page 14

®

ELECTRIC CHAIN SAW

OPERATING CHAIN SAW

Continued

BUCKING A LOG

WARNING: Avoid kickback. Kickback can result in severe in- jury or death. See Kickback, pages 3 and 4, to avoid risk of kickback.

WARNING

•If on slope, make sure log will not roll down hill. Secure log by using wooden stakes. Drive wooden stakes into ground on downhill side of log. Stand on uphill side of log while cutting. Log may roll after cutting.

•Never try cutting through two logs at same time. This could increase the risk of kickback.

•While cutting log, never hold log with your hand, leg, or foot.

•While cutting log, never allow another person to hold log.

•Turn off and unplug saw be- fore moving from one place to another.

CAUTION: Seek professional help if facing conditions beyond your ability.

Bucking a log is cutting a log into sections. Make sure your footing is firm. Keep feet apart. Divide your weight evenly on both feet. Stand slightly to left of saw. This keeps your body from being in direct line with chain. When possible, raise log or section off ground. Do this by using limbs, logs, chocks, etc.

When cutting through log, maintain control by reducing cutting pressure near end of cut. Do not relax your grip on chain saw handles. Do not let moving chain touch ground. Ground will dull moving chain. After cut- ting through log, release trigger to turn saw off before moving saw.

Follow directions in column 2 to buck a log.

Entire Length Of Log On

Ground

1.Cut log from top (see Figure 15).

Figure 15 - Bucking Log With Entire Length On Ground

Log Supported On One End

1.Make first cut on underside of log (see Figure 16). Use top of guide bar to make this cut. Cut 1/3 through diam- eter of log. This cut will keep section from splintering when cut.

2.Make second cut directly above first cut. Cut down to meet first cut. This cut will keep log from pinching guide bar and chain.

2nd Cut

1st Cut

Figure 16 - Bucking Log When Log Is Supported On One End

Log Supported On Both Ends

1.Make first cut from above log (see Fig- ure 17). Cut 1/3 through diameter of log. This cut will keep section from splintering when cut.

2.Make second cut on underside of log, directly under first cut. Use top of guide bar to make this cut. Cut up to meet first cut. This will keep log from pinch- ing guide bar and chain.

1st Cut

2nd Cut

Figure 17 - Bucking Log When Log Is Supported On Both Ends

CLEANING AND MAINTENANCE

NOTICE: Below are instructions for servicing your chain saw. Any servicing not mentioned below should be done by an authorized service person.

CLEANING SAW BODY

WARNING: Unplug chain saw from power source before servic- ing. Severe injury or death could occur from electrical shock or body contact with moving chain.

WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain.

WARNING: When cleaning saw body,

•do not submerge saw in any liquids

•do not use products that con- tain ammonia, chlorine, or abrasives

•do not use chlorinated clean- ing solvents, carbon tetrachlo- ride, kerosene, or gasoline

Keep saw body clean. Use a soft cloth damp- ened with a mild soap and water mixture. Wipe saw body to clean.

12

102891

Page 13 Page 15
Image 14
Page 13 Page 15
Contents MODEL/MODELL/MODÈLE 100271-01230V~ 50Hz 1450W 102891 Electric Chain SAW Information Symbols Safety Information Warnings Appears Throughout This ManualBefore Operating Chain SAW SafetyKickback Safety Devices On This Saw KickbackPushback and PULL-IN Saw Maintenance and Kickback SafetySecure wood you are cutting by using clamps or chocks Chain SAW OperationRear Handle Handle located at rear of saw body Maintenance and Storage of Chain SAWChain SAW Names and Terms Reduced Kickback Guide Bar GuideProduct Identification AssemblyImportant Do not clamp chain saw in vise during assembly UnpackingFilling OIL Tank Assembling Guide Bar, Chain, and Hand GuardExtension Cords SAW Chain Tension AdjustmentOperating Chain SAW Cutting with the Chain SAW Oiling ChainChain Brake Trimming a Tree Pruning Before Felling a TreeFelling Notch Felling ProcedureLimbing a Tree Felling CutBucking a LOG Cleaning and MaintenanceCleaning SAW Body Sharpening Your SAW Chain Normal Guide Bar MaintenanceCare of Guide BAR Items Needed to Sharpen ChainStorage Replacement PartsRecycling Troubleshooting Observed Fault Possible Cause RemedyWarranty Information Importer Manufacturer Desa Europe B.VElektrische Kettingzaag Gebruikershandleiding Betekenis Symbolen Elektrische KettingzaagTerugslag WAARSCHUWIN- GENAlvorens DE Kettingzaag TE Gebruiken Veiligheidsvoorzieningen tegen terugslagKettingzaagonderhoud en terugslagveiligheid Duwen EN TrekkenMET DE Kettingzaag Werken Oorzaken van duwen en trekkenDE Kettingzaag Onderhouden EN Opbergen Breng de beschermkap aanBenamingen EN Termen UitpakkenIdentificatie VAN Onderdelen MontageNing van de ketting bij te stellen Olie BijvullenDE Spanning VAN DE Ketting BIJ- Stellen DE Ketting Olien DE Kettingzaag BedienenVerlengsnoeren EEN Boom Snoeien ZagenDE Kettingrem Alvorens een boom om te zagen EEN Boom OmzagenVeltechniek ValkerfTakken Verwijderen EEN Stam in Stukken ZagenDe stam ligt over de gehele lengte op de grond Schoonmaak EN OnderhoudDE Behuizing Schoonmaken De stam is aan één uiteinde ondersteundNormaal onderhoud van de kettinggeleider Zorg Voor DE KettinggeleiderDE Ketting Slijpen Gereedschap benodigd voor het slijpen van de kettingDe dieptebegrenzers van de snijtanden vijlen De ketting vervangenWaarschuwing Gebruik uitsluitend in deze handleiding DE Kettingzaag OpbergenVERVANGINGS- Onderdelen Onderdeelnummer OmschrijvingDe olietank leeglopen wanneer de zaag Problemen OplossenPagina Langere tijd niet gebruikt wordtBeperkte Garantie Elektrische Kettingzaag Importeur Fabrikant Desa Europe B.VModèle 100271-01 230V~ 50Hz 145a0W Description Symboles Lire le manuel d’instructionsRecul Avertissements Pour LA SécuritéAvant D’UTILISER LA Tronçonneuse Cause du reculEntretien de la tronçonneuse et protection contre le recul Poussée ET TractionUtilisation DE LA Tronçonneuse Causes de la poussée et de la tractionDans un endroit sec Vocabulaire DE LA TronçonneuseEntretien ET Remisage DE LA Tronçonneuse Nomenclature DES Pièces Tronçonneuse électriqueDéballage AssemblageUtilisation DE LA Tronçonneuse Remplissage DU Réservoir D’HUILERéglage DE LA Tension DE LA Chaîne Rallonges DE CordonFrein DE Chaîne Lubrification DE LA ChaîneSciage Avec LA Tronçonneuse Abattage D’UN Arbre Avant d’abattre un arbreSifflet d’abattage Procédure D’ABATTAGEÉbranchage Trait d’abattageLa bille est soutenue à une extrémité Tronçonnage D’UNE BilleToute la bille repose au sol La bille est soutenue aux deux extrémitésEntretien DE LA LAME- Guide Nettoyage ET EntretienNettoyage DU Carter DE LA Tronçonneuse Affûtage DE LA ChaîneLimage des limiteurs de profondeur des taillants Remplacement de la chaîneAffûtage des taillants Pièces DE Rechange RecyclageRemisage Remiser la chaîneDépannage Instructions D’UTILISATION Information SUR LA Garantie Importateur Fabricant Desa Europe B.VModell 100271-01230V~ 50Hz 1450W Elektrokettensäge Erklärung ZeichenRückprall SICHERHEITS- HinweiseVOR Gebrauch DER Motorsäge Rückprall- Sicherheitsvorrichtungen an dieser SägeWartung der Säge und Rückprallsicherheit STOSS- UND ReisskräfteBetriebssicherheit Die Ursache von Stoß- und ReißkräftenWarten UND Lagern DER Motorsäge Vorderer Handgriff Befindet sich am vor- deren Sägenrumpf BEGRIFF- SerklärungenDIE Teile DER Motorsäge Auspacken ZusammenbauFüllen DES Ölbehälters Einstellen DER SÄGEKETTEN- SpannungÖlen DER Kette Gebrauch DER MotorsägeVerlängerungskabel SägeanleitungVom Baum aus KettenbremseFällen Eines Baums Fallkerb FällanleitungVor dem Fällen eines Baums FällschnittStamm liegt der Länge nach auf dem Boden Entasten Eines BaumsAblängen Stamm an einem Ende aufgebocktPflege DES Schwertes Reinigung UND WartungReinigen DES Sägenrumpfes Routinewartung DES SchwertesSchärfen der Schneidezähne Schärfen DER SägeketteZum Schärfen der Kette benötigtes Werkzeug Ersatzteile Wiederver WertungLagerung Öl ist zu zähflüssig Öl mit einer geeigneten Viskosität ver StörungssucheSäge schneidet nur unter starkem Druck Kette ist stumpf Schwert und Kette nicht richtig zusamNotizen Befristete Garantie GarantieBitte GUT Aufbewahren Importeur Hersteller102891 Desa Europe B.V

100271-01 specifications

Desa 100271-01 is an innovative and efficient solution designed to enhance agricultural practices. Targeted primarily at small to medium-sized farms, this technology integrates advanced features that optimize farming processes, ultimately improving yield and reducing operational costs.

One of the standout features of Desa 100271-01 is its precision agriculture capability. Utilizing GPS and IoT (Internet of Things) technologies, the system enables farmers to manage their fields more effectively. The GPS technology ensures accurate field mapping, allowing for more efficient planting patterns and resource distribution. By monitoring crop health through real-time data collection, farmers can make informed decisions regarding watering, fertilization, and pest control, leading to healthier crops and minimized waste.

The platform is designed with user-friendliness in mind. Its intuitive interface allows farmers of varying technical backgrounds to navigate the system easily. Training is often included as part of the purchase, ensuring that users can maximize the potential of the Desa 100271-01 right from the start. Additionally, compatibility with mobile devices enables farmers to access information and controls from the field, enhancing operational flexibility.

Another notable characteristic is its sustainability focus. The Desa 100271-01 promotes eco-friendly agricultural practices by providing data-driven insights that help reduce water and fertilizer usage. This not only contributes to lower operational costs but also supports environmental conservation efforts.

In terms of connectivity, Desa 100271-01 employs robust wireless technologies to facilitate communication between various devices on the farm. This interconnectivity allows for real-time monitoring and control of agricultural equipment, leading to enhanced efficiency. The system can be integrated with existing farm machinery, making it a versatile addition to any agricultural setup.

Furthermore, the Desa 100271-01 is designed to withstand challenging agricultural environments. Its durable construction and weather-resistant features ensure reliable performance, even in adverse conditions.

Overall, Desa 100271-01 represents a significant advancement in agricultural technology. With its precision farming capabilities, user-friendly interface, sustainability initiatives, and robust connectivity, it stands out as a valuable asset for modern agricultural practices, contributing to increased efficiency and profitability for farmers.
Top Page Image Contents