Husqvarna FS 413 manual Before Operation, Re-Locating the Blade Guard C If Required

Page 21

OPERATION

Before Operation:

Use: This machine is used only for wet or dry sawing of old and new concrete and asphalt.

WARNING!

DO NOT use for dry cutting in European Union (EU) regions. Machine is not equipped with a dust port.

Tools: Use machine only with the following tools (H): Wa- ter Cooled Diamond Blades. Reinforced Abrasive Blades or Dry Cutting Diamond blades should NOT be used with- in European Union (EU) regions because this machine, as supplied, does not include a dust collector port.

Diameter: 300 mm (12”) – 500 mm (20”).

Bore: 25.4mm (1.00”).

WARNING!

DO NOT use carbide, wood saw, or circular saw blades on this machine, else injury or death could oc- cur.

Re-Locating the Blade Guard (C) - If Required:

Blade Guard (C) is factory installed on right hand side of machine, but can be relocated to left side. This may allow cutting closer to obstacles, if approaching them from the opposite direction is not possible.

1.Use 13mm Wrench (U) to remove Blade Guard Rear Bolt (E) from Blade Guard (C).

2.Push back collar to separate Water Hose Disconnect

(G). Male half remains with Blade Guard (C). Female half remains with Water Tank (P) or Water Control Valve (KK).

3.Lift Blade Guard (C) upward, and off of Blade Guard Mounting Spade (Y).

4.Use 13mm Wrench (U) to remove four (4) screws that attach Blade Guard Latch Plate (F). Re-attach the Blade Guard Latch Plate (F) to the left hand side of Blade Guard

(C).

5.Remove and relocate Shaft Guard (W) from left hand side of machine to right hand side.

6.Lower Blade Guard (C) onto Blade Guard Mounting Spade (Y) on left hand side of machine.

7.Re-Install Rear Bolt (E) in Blade Guard (C).

8.Re-Attach Water Hose Disconnect (G) from Blade Guard (C) to Water Tank (P) or Water Valve (KK). Take care that relocated hose will not contact muffler.

9.Relocate and realign Front Pointer (A) so Guide Wheel

(B) is on left side of machine.

WARNING!

Before operating machine, read and under- stand this entire operation manual & engine operation manual supplied with engine.

Be familiar with machine before operation!

Operator must wear personal protective equipment & cloth- ing appropriate to the work he is doing. Personal protective equipment, such as hearing & eye protec- tion, is mandatory.

21

Image 21

Contents Page Page Contents and Introduction Symbols and Decals Symbols and Decals Symbols and Decals Symbols and Decals Location Blade Guard 543 04 57-88SOUND Level 108dBADust Warning Safety InstructionsGeneral use California Prop 65 WarningPoison Exhaust GAS Hearing HazardGeneral Information Instructions could Result in Death or Serious Bodily Injury Safety Instructions Safety FirstDo not Page Is moved Parts Identification What is WhatBlade Arbor Blade H mounts on this surface Water Tank / Lifting Point Support Holds Water TankParts Identification What is What Assembly Install Front Pointer a Blade Guard Front DRe-Position Blade Depth Control Handle EE Torque Lifting Eye NUT to 83 N-m 61 lb-ft mini Mum Install Water Tank P if equippedAssembly Filling Water Tank Operation Before OperationRe-Locating the Blade Guard C If Required Transporting & Lifting Machine Lifting machine equipped with Water TankParking Machine All Models Gasoline Engine ModelsFitting the Diamond Blade H Starting and cutting with machine Scheduled Maintenance Quick Reference Maintenance & LubricationService Daily Service Every 50 HoursChanging Engine Oil Engine Oil Checking Engine OilGovernor Speed Model Blade Shaft Engine2600 3600 Engine Will Not Start Cause Action Trouble Shooting GuideWiring Diagram EMC Technical DataHAV Model Maximum Vibration Aeq in m/s Maximum Exposure TimeModel Nominal Maximum Mass kg 124 158 Cutting DepthAccessories Conformity Certificates West 119th Street, Olathe, Kansas 66061 USA26October2006, Olathe, Kansas USA Construction Products, North America Corporate Office Contact InformationPage ¡ADVERTENCIA Símbolos y Calcomanías Símbolos y Calcomanías Símbolos y Calcomanías Símbolos y Calcomanías 543 04 57-88SOUND Level 108dBA Advertencia Sobre EL Polvo Instrucciones DE SeguridadUso general Advertencia Prop 65 de CaliforniaGAS DE Escape Tóxico AdvertenciaRiesgos Auditivos Información generalLOS SÍ Y LOS no Instrucciones DE Seguridad ¡LA Seguridad ES LO PrimeroAdvertencias Notas Identificación DE LAS Piezas QUÉ ES QUÉ Tanque de agua si se incluye 25 litrosDe operación del motor Rote hacia abajo, de manera tal que quede fija hacia adentro Vuelva a posicionar el manubrio trasero JJ EnsambladoDisponga la cuerda del puntero de manera tal que Instale el puntero delantero aProtección delantera de la cuchilla D En su sitioDe accidentes o muerte al levantar la máquina Instale el tanque de agua P de incluirseEnsamblado Llenado del tanque de agua Funcionamiento Antes de poner en funcionamientoDe control de agua KK Izado de la máquina equipada con el tanque de agua Transporte e izado de la máquinaEstacionamiento de la máquina Quite la cuchilla H antes del izado, carga o transporteTodos los modelos Modelos con motor a gasolinaColocación de la cuchilla adiamantada H Arranque de la máquina y proceso de corte Levante la sierra hasta la altura máxima. Ahora, conPresione suavemente el manubrio trasero JJ Referencia Rápida DE Mantenimiento Programado Mantenimiento Y LubricaciónServicio Diario Servicio Cada 50 HorasRecambio de aceite del motor Aceite del motor Controle el aceite del motorHerramientas necesarias MM mantiene la tensión de la mismaVelocidad del regulador El exceso de velocidad en la cuchilla adiamantadaEl motor no arranca Causa Acción Guía Para LA Determinación Y Resolución DE ProblemasDiagrama DE Cableado CEM Datos TécnicosVMB Vibración de mano / brazoModelo Peso nominal Peso máximo 124 158 Modelo RPM del eje de RPM del moTor Accesorios Certificados DE Cumplimiento Husqvarna Construction Products, North America Sede Social Información DE ContactoPage Avertissement Symboles et Autocollants Symboles et Autocollants Symboles et Autocollants Symboles et Autocollants 543 04 57-88SOUND Level 108dBA Avertissement Concernant LA Poussière Instructions DE SécuritéGénéralités CarburantAvertissement GAZ D’ÉCHAPPEMENT ToxiquesInformation générale Faire ET À NE PAS Faire Instructions DE Sécurité Sécurité D’ABORDFaire Inhabituelle, NE PAS Utiliser LE DisqueNE PAS Faire Page Réservoir d’eau le cas échéant Capacité de Identification DES PiècesIdentification DES Pièces Mettre le guidon JJ en position correcte AssemblageTirer la manette de commande de profondeur de disque Poser la flèche avant aAvant du protège-disque D Serrer l’ÉCROU de l’étrier de levage à 83 Nm Lb-ft minimum Poser le réservoir d’eau P le cas échéantAssemblage Remplir le réservoir d’eau Déplacement du protège-disque C Si nécessaire UtilisationAvant utilisation De ce document Transport et levage de la machineLevage d’une machine équipée d’un réservoir d’eau Stationner la machineTirer le levier OO vers le centre de la machine Modèles à moteur essenceTous modèles Pose du disque diamanté H Démarrer et scier avec la machine Guide Rapide D’ENTRETIEN Courant Entretien ET LubrificationFaire Chaque Jour Faire Toutes LES 50 HeuresHuile moteur Contrôle de l’huile moteur Graisseur de la commande de profondeurVérifier que le niveau d’huile moteur est correct Changer l’huile moteurOutillage nécessaire La courroie d’entraînementSerrer au couple indiqué à la figure Vitesse du régulateurLe moteur ne démarre pas Cause Action Guide DE DépannageSchéma DE Câblage Vibrations main-bras Données Techniques100 Modèle Masse Masse maximale Nominale kg 124 158101 AccessoiresCertificats DE Conformité Directive 98/37/CE et aux règles régissant sa transpositionOctobre 2006, Olathe, Kansas USA 102 103 Informations DE Contact104