Husqvarna FS 413 manual Starting and cutting with machine

Page 25

OPERATION

Starting and cutting with machine:

•Using the Depth Control (EE), raise Diamond Blade

(H) as high as possible so it will not strike pavement when maneuvering. Pull out on Blade Depth Stop (FF) if required.

•Dis-engage parking brake (if equipped).

•Maneuver machine into position near line to be cut.

•Lower Front Pointer (A) onto cutting surface.

•Set Depth Indicator (GG) (use if desired):

1)Lower machine until diamond blade contacts cutting surface.

2)Set Depth Indicator (GG) dial to align indicator arrows with zero (0). Orange color indicates cutting depth in centimeters. White color indicates inches.

3)Raise saw to maximum height. Now as Diamond Blade

(H) is lowered, Depth Indicator (GG) will show cutting depth.

4)Return Diamond Blade (H) to fully raised position.

•Verify that both Emergency Stop Switch (AA) AND Engine Start Switch (DD) are in “ON” position. Emer- gency Stop Switch (AA) should be in outer position (pulled outward from cowl). Engine Start Switch (DD) must be turned to “1” (ON) position.

•Start Engine. See engine manual for more information.

•Visually verify that tool rotation matches directional ar- row on blade guard.

•Open Water Control Valve (KK) FULL open. Verify full water flow, and then adjust for proper amount of water on the blade BEFORE you lower the Blade.

•Make final adjustments to align saw with cutting line.

Verify that Guide Wheel (B), and Diamond Blade (H) are both on the cutting line.

If water supply is interrupted, stop cutting immediate- ly. Damage to Diamond Blade (H) could occur.

•Lower Diamond Blade (H) into the cut by slowly turning Blade Depth Control (EE) COUNTER-CLOCKWISE.

•When desired depth of cut is reached, push Blade Depth Stop (FF) down to lock it to Blade Depth Control (EE) (if desired).

•Gently push Rear Handle (JJ) to propel machine for- ward. Watch Diamond Blade (H) and Guide Wheel (B) carefully to assure that machine stays on cutting line.

•When cut is complete, dis-engage Blade Depth Stop (FF).

•Raise Diamond Blade (H) out of cut by slowly turning Blade Depth Control (EE) CLOCKWISE.

•Close Water Control Valve (KK).

•Turn engine to “0” (OFF) position using the Engine Start Switch (DD).

NOTICE

If an urgent situation arises during cutting opera- tions STOP machine immediately using Emergency Stop Switch (AA).

For EMERGENCY STOP of machine, press down EMERGENCY STOP SWITCH (AA).

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Page Page Contents and Introduction Symbols and Decals Symbols and Decals Symbols and Decals Symbols and Decals Location Blade Guard 543 04 57-88SOUND Level 108dBADust Warning Safety InstructionsGeneral use California Prop 65 WarningHearing Hazard Poison Exhaust GASGeneral Information Instructions could Result in Death or Serious Bodily Injury Safety Instructions Safety FirstDo not Page Is moved Parts Identification What is WhatBlade Arbor Blade H mounts on this surface Water Tank / Lifting Point Support Holds Water TankParts Identification What is What Assembly Blade Guard Front D Install Front Pointer aRe-Position Blade Depth Control Handle EE Torque Lifting Eye NUT to 83 N-m 61 lb-ft mini Mum Install Water Tank P if equippedAssembly Filling Water Tank Before Operation OperationRe-Locating the Blade Guard C If Required Lifting machine equipped with Water Tank Transporting & Lifting MachineParking Machine All Models Gasoline Engine ModelsFitting the Diamond Blade H Starting and cutting with machine Scheduled Maintenance Quick Reference Maintenance & LubricationService Daily Service Every 50 HoursChanging Engine Oil Engine Oil Checking Engine OilModel Blade Shaft Engine Governor Speed2600 3600 Engine Will Not Start Cause Action Trouble Shooting GuideWiring Diagram EMC Technical DataHAV Model Maximum Vibration Aeq in m/s Maximum Exposure TimeModel Nominal Maximum Mass kg 124 158 Cutting DepthAccessories West 119th Street, Olathe, Kansas 66061 USA Conformity Certificates26October2006, Olathe, Kansas USA Construction Products, North America Corporate Office Contact InformationPage ¡ADVERTENCIA Símbolos y Calcomanías Símbolos y Calcomanías Símbolos y Calcomanías Símbolos y Calcomanías 543 04 57-88SOUND Level 108dBA Advertencia Sobre EL Polvo Instrucciones DE SeguridadUso general Advertencia Prop 65 de CaliforniaGAS DE Escape Tóxico AdvertenciaRiesgos Auditivos Información generalLOS SÍ Y LOS no Instrucciones DE Seguridad ¡LA Seguridad ES LO PrimeroAdvertencias Notas Tanque de agua si se incluye 25 litros Identificación DE LAS Piezas QUÉ ES QUÉDe operación del motor Rote hacia abajo, de manera tal que quede fija hacia adentro Vuelva a posicionar el manubrio trasero JJ EnsambladoDisponga la cuerda del puntero de manera tal que Instale el puntero delantero aProtección delantera de la cuchilla D En su sitioDe accidentes o muerte al levantar la máquina Instale el tanque de agua P de incluirseEnsamblado Llenado del tanque de agua Antes de poner en funcionamiento FuncionamientoDe control de agua KK Izado de la máquina equipada con el tanque de agua Transporte e izado de la máquinaEstacionamiento de la máquina Quite la cuchilla H antes del izado, carga o transporteTodos los modelos Modelos con motor a gasolinaColocación de la cuchilla adiamantada H Levante la sierra hasta la altura máxima. Ahora, con Arranque de la máquina y proceso de cortePresione suavemente el manubrio trasero JJ Referencia Rápida DE Mantenimiento Programado Mantenimiento Y LubricaciónServicio Diario Servicio Cada 50 HorasRecambio de aceite del motor Aceite del motor Controle el aceite del motorHerramientas necesarias MM mantiene la tensión de la mismaVelocidad del regulador El exceso de velocidad en la cuchilla adiamantadaEl motor no arranca Causa Acción Guía Para LA Determinación Y Resolución DE ProblemasDiagrama DE Cableado CEM Datos TécnicosVMB Vibración de mano / brazoModelo RPM del eje de RPM del mo Modelo Peso nominal Peso máximo 124 158Tor Accesorios Certificados DE Cumplimiento Husqvarna Construction Products, North America Sede Social Información DE ContactoPage Avertissement Symboles et Autocollants Symboles et Autocollants Symboles et Autocollants Symboles et Autocollants 543 04 57-88SOUND Level 108dBA Avertissement Concernant LA Poussière Instructions DE SécuritéGénéralités CarburantGAZ D’ÉCHAPPEMENT Toxiques AvertissementInformation générale Faire ET À NE PAS Faire Instructions DE Sécurité Sécurité D’ABORDFaire Inhabituelle, NE PAS Utiliser LE DisqueNE PAS Faire Page Réservoir d’eau le cas échéant Capacité de Identification DES PiècesIdentification DES Pièces Mettre le guidon JJ en position correcte AssemblagePoser la flèche avant a Tirer la manette de commande de profondeur de disqueAvant du protège-disque D Serrer l’ÉCROU de l’étrier de levage à 83 Nm Lb-ft minimum Poser le réservoir d’eau P le cas échéantAssemblage Remplir le réservoir d’eau Utilisation Déplacement du protège-disque C Si nécessaireAvant utilisation De ce document Transport et levage de la machineLevage d’une machine équipée d’un réservoir d’eau Stationner la machineModèles à moteur essence Tirer le levier OO vers le centre de la machineTous modèles Pose du disque diamanté H Démarrer et scier avec la machine Guide Rapide D’ENTRETIEN Courant Entretien ET LubrificationFaire Chaque Jour Faire Toutes LES 50 HeuresHuile moteur Contrôle de l’huile moteur Graisseur de la commande de profondeurVérifier que le niveau d’huile moteur est correct Changer l’huile moteurOutillage nécessaire La courroie d’entraînementSerrer au couple indiqué à la figure Vitesse du régulateurLe moteur ne démarre pas Cause Action Guide DE DépannageSchéma DE Câblage Vibrations main-bras Données Techniques100 Modèle Masse Masse maximale Nominale kg 124 158101 AccessoiresDirective 98/37/CE et aux règles régissant sa transposition Certificats DE ConformitéOctobre 2006, Olathe, Kansas USA 102 103 Informations DE Contact104
Top Page Image Contents