Alarm ENABLE/DISABLE AT Power on | a/d/s/ iSeries specification

ALARM ENABLE/DISABLE AT POWER ON:

Press d 15) Display flashes previous selection. Press b to ENBL enable or DSBL disable.

Press d 16) Display shows STRD stored message. momentarily and

then advances to ALR.L only, if it was changed, otherwise press a to advance to the ALR.L Alarm 1 Low Value Submenu.

If the alarm is enabled at Power On, the alarm will be active right after reset. If the alarm is disabled at Power On, the alarm will become enabled when the process value enters the non alarm area. The alarm is not active while the process value is approaching Setpoint 1.

ALARM 1 LOW VALUE SUBMENU:

Press d 17) Display flashes 1st digit of previous value. Use b and c to enter new value.

Press b & c 18) Use b and c to enter Alarm 1 Low Value.

Press d 19) Display shows STRD storage message momentarily and then advances to ALR.H only, if it was changed, otherwise press a to advance to ALR.H Alarm 1 Hi Value Submenu.

ALARM 1 HI VALUE SUBMENU:

Press d 20) Display flashes 1st digit of previous value. Use b and c to enter new value.

Press b & c 21) Use b and c to enter Alarm1 Hi Value.

Press d 22) Display shows STRD stored message momentarily and then advances to the next menu only, if it was changed, otherwise press a to advance to the next menu.

28

Image 32

a/d/s/ iSeries manual Alarm ENABLE/DISABLE AT Power on, Alarm 1 LOW Value Submenu, Alarm 1 HI Value Submenu

Contents

Newport Electronics,Inc Newport Electronics,Inc Table of Contents Flow Chart for Alarm 1 Menu Flow Chart for Alarm 2 Menu Input Properties Factory Preset ValuesList of Figures List of Tables TIP Part Introduction Description Safety Considerations EMC Considerations Before You Begin Part Setup Optional Remote Programmer Front Panel Power Front Panel ConnectionsInput Output Electrical Installation Power Connections Main Power Connections Fuse Requirement see specifications Thermocouple Wiring Hookup TC Wire Color Chart Thermocouple Input 3 Two/Three/Four-Wire RTD Ohm Wiring Hookup Process Current Process Voltage Wiring Outputs Isolated Analog Output Wiring Hookup 10 Snubber Circuits Wiring Hookup 13 Excitation Output Part Operation Configuration Mode IntroductionButton Function in Configuration Mode Menu Configuration Flow Chart for ID and Set Points ID Number Entering Your NON-DEFAULT Full Security ID NumberEntering Your NON-DEFAULT SETPOINT/ID Security ID Number Set Points Setpoint Input Type Menu Configuration MenuEnter Configuration Menu Input Type Thermocouple Enter Input Type MenuThermocouple Submenu Thermocouple Types Input Type RTD RTD SubmenuRTD Types RTD Value Submenu Reading Configuration Menu Input Type ProcessProcess Submenu Process Types Enter Reading Configuration Menu Temperature Unit SubmenuDecimal Point Submenu Filter Constant Submenu Reading Configuration If Process was selected INPUT/READING Scale and Offset Submenu Conversion Table Range Conversion Number Alarm Enter Alarm 1 Menu Alarm 1 LATCH/UNLATCH Submenu Alarm 1 ENABLE/DISABLE SubmenuAlarm 1 ABSOLUTE/DEVIATION Submenu Contact Closure Submenu Active Submenu Alarm 1 HI Value Submenu Alarm ENABLE/DISABLE AT Power onAlarm 1 LOW Value Submenu Enter Alarm 2 Menu Loop Break ENABLE/DISABLE Submenu Loop Break Time/Field CalibrationEnter Loop Break Time Menu Loop Break Time Value Submenu Thermocouple Field Calibration Submenu Reading Adjust SubmenuSetpoint Deviation ENABLE/DISABLE Submenu Flow Chart for Output Output MINIMUM/PERCENT LOW Submenu Enter Output 1 MenuSelf Submenu Action Type Submenu MAXIMUM/PERCENT High SubmenuControl Type Output Relay, SSR, or Pulse Auto PID Submenu Anti Integral Submenu Start Auto Tune PID Proportional Band Submenu Cycle Time Submenu Reset Setup SubmenuRate Setup Submenu Damping Factor Submenu Deadband Submenu CURRENT/VOLTAGE Submenu Analog Output RetransmissionEnter Analog Output Menu Reading OUT Ramp ENABLE/DISABLE Submenu Soak ENABLE/DISABLE SubmenuRamp & Soak Enter Ramp and Soak Menu Ramp Value Submenu Soak Value Submenu Enter ID Code Menu Entering or Changing Your NON-DEFAULT ID CodeID Code SETPOINT/ID Security Level Submenu Entering or Changing Your Default ID CodeFull Security Level Submenu 12 Flow Chart for Communication Option Communication Option Enter Communication Option Menu Communication Parameters SubmenuBaud Submenu Parity Submenu Stop BIT Submenu BUS Format SubmenuModbus Protocol Submenu Line Feed Submenu Data Separation Character Submenu Data Flow Mode SubmenuCommunication Interface Standard Submenu Alarm Status Submenu Data Format SubmenuMain Reading Submenu Peak Value Submenu Address Setup Submenu Address Value SubmenuTransmit Time Interval Submenu Transmit Time Interval Value Submenu Alarm 1 Display Color Submenu Display Color SelectionEnter Display Color Selection Menu Normal Color Display Submenu Alarm 2 Display Color Submenu ExampleDisplay Colors change sequences Green RED Amber Amber RED Green Part Specifications Control Control OutputSSR Communications General ExcitationInsulation Input Properties Input Type Range Accuracy Part 5 Factory Preset Values Factory preset value Display Color Colr Part CE Approvals Information Measurement CategoryPage Page Page Warranty/Disclaimer M4165/N/0206