a/d/s/ iSeries - page 56

52

ALARM 2 DISPLAYCOLOR SUBMENU:

Press d11) Display flashes previous selection for “Alarm 2 Color Display”.

Press b12) Scroll through the available selections: GRN, RED or AMBR.

Press d13) Display shows STRD stored message momentarily and then

momentarily shows the software version number, followed by

RST Reset, and then proceeds to the Run Mode.

IN ORDER TO DISPLAYONE COLOR, SET THE SAME DISPLAY

COLOR ON ALLTHREE SUBMENUS ABOVE.

If user wants the Display to change color every time when both Alarm 1

and Alarm 2 are triggered, the Alarm values should be set in such a way

that Alarm 1 value is always on the top of Alarm 2 value, otherwise value

of Alarm 1 will overwrite value of Alarm 2 and Display Color would not

change when Alarm 2 is triggered.

Example 1:

Output 1 & Alarm 2: SSR

Alarm Setup: Absolute, Above, Alarm 2 HI Value “ALR.H” = 200, Alarm 1

HI Value “ALR.H” = 400

Color Display Setup: Normal Color “N.CLR” = Green, Alarm 1 Color

“1.CLR” = Amber, Alarm 2 Color “2.CLR” = Red

Display Colors change sequences:

GREEN RED AMBER

•--➤------------------------------•-----------------------------•------------------------------➤

0 AL2.H = 200 AL1.H = 400

Example 2:

Output 1 & Alarm 2: Pulse

Alarm Setup: Absolute, Below, Alarm 2 Low Value “ALR.L” = 300, Alarm 1

Low Value “ALR.L” = 100

Color Display Setup: "N.CLR" = Green, "1.CLR" = Amber, "2.CLR" = Red

Display Colors change sequences:

AMBER RED GREEN

•--------------•----------------------------------•------------------------------------------- --•

0 AL1.L= 100 AL2.L = 300

➤ ➤

Contents

Main In the U.S.A. and Canada: 1-800-NEWPORT In Mexico: (95) 800-NEWPORT Or call your local NEWPORT Office. NEWPORT Electronics,Inc. TABLE OF CONTENTS LIST OF FIGURES: LIST OF TABLES: NOTES, WARNINGS and CAUTIONS PART 1 INTRODUCTION 1.1 Description 1.2 Safety Considerations EMC Considerations 1.3 Before You Begin Page 2.2 Front Panel Connections Figure 2.2 Input and Output Connections Table 2.2 Connectors 2.3 Electrical Installation 2.3.1 Power Connections Figure 2.3 Main Power Connections Table 2.3 Fuse Requirement (see specifications) 2.3.2 Thermocouple Input Figure 2.4 Thermocouple Wiring Hookup Table 2.4 TC Wire Color Chart 2.3.3 Two/Three/Four-Wire RTD Figure 2.5 a) RTD-1000 ohm and b) RTD-100 ohm Wiring Hookup 500 ohm Wiring Hookup Page 2.3.6 Wiring Outputs Figure 2.8 a) Mechanical Relay and SSR b) Pulse Output Outputs Wiring Hookup Wiring Hookup Figure 2.9 Isolated Analog Output Wiring Hookup Figure 2.10 Snubber Circuits Wiring Hookup Figure 2.11 Typical Applications RC CIRCUIT VARISTOR C NC NO C NC NO Page PART 3 OPERATION: Configuration Mode 3.1 Introduction Table 3.1 Button Function in Configuration Mode a b c Page 3.2.1 ID Number 3.2.2 Set Points Page Input Type (Thermocouple) Input Type (RTD) Input Type (Process) 3.2.5 Reading Configuration Menu Figure 3.4 Flow Chart for Reading Configuration Menu Page Reading Configuration (If Process was selected) Table 3.2 Conversion Table 3.2.6 Alarm 1 Figure 3.5 Flow Chart for Alarm 1 Page Page Page 3.2.7 Alarm 2 Figure 3.6 Flow Chart for Alarm 2 3.2.8 Loop Break Time/Field Calibration Figure 3.7 Flow Chart for Loop Break Time/Field Calibration Page Page Page Page Page Page Page Page 3.2.10 Analog Output (Retransmission) Figure 3.9 Flow Chart for Analog Output (Retransmission) Page 3.2.11 Ramp & Soak Figure 3.10 Flow Chart for Ramp and Soak Page 3.2.12 ID CODE Figure 3.11 Flow Chart for ID Code Page Page Page Page Page Page Page 3.2.14 DISPLAYCOLOR SELECTION Figure 3.13 Flow Chart for Display Color Selection Page Page PART 4 SPECIFICATIONS Page Page J K T E R S B C N L RTD Table 4.1 Input Properties PART 5 FACTORY PRESET VALUES Table 5.1 Factory preset value Page PART 6 CE APPROVALS INFORMATION Page Page Page Warranty/Disclaimer Return Requests/Inquiries