Manuals / Brands / Computer Equipment / Network Card / a/d/s/ / Computer Equipment / Network Card

a/d/s/ iSeries 3.2.10 Analog Output (Retransmission), Figure 3.9 Flow Chart for Analog Output (Retransmission)

1 69

Download 69 pages, 1.03 Mb

39

3.2.10 Analog Output (Retransmission)

This unit is equipped with three physical outputs that can only be configured as

follows:

a) Alarm 1, Alarm 2 & Analog Out

b) Output 1, Alarm 2 & Analog Out

Analog Output is available only if the Analog Output option board is factory

installed.

Figure 3.9 Flow Chart for Analog Output (Retransmission)

ENTER ANALOG OUTPUT MENU:

Press a1) Press a, if necessary, until CNFGprompt appears.

Press d2) Display advances to INPT Input Menu.

Press a3) Press a, if necessary, until Display advances to ANLG

Analog Output Menu.

Press d4) Display advances to Analog Output CURRor VoLT

Current/Voltage Submenu and flashes the previous selection.

CURRENT/VOLTAGE SUBMENU:

Press d5) Display flashes CURR Current or VoLT Voltage.

Press b6) Scroll through the available selection: Current or Voltage.

(Example VoLT).

Press d7) Display shows STRD stored message momentarily and then

advances to RD1 Submenu only if it was changed, otherwise

press ato advance to RD1 Reading 1 Submenu.

It is required that you put the controller in the Standby Mode for any

configuration change other than Set Points & Alarms.

Contents

Main In the U.S.A. and Canada: 1-800-NEWPORT In Mexico: (95) 800-NEWPORT Or call your local NEWPORT Office. NEWPORT Electronics,Inc. TABLE OF CONTENTS LIST OF FIGURES: LIST OF TABLES: NOTES, WARNINGS and CAUTIONS PART 1 INTRODUCTION 1.1 Description 1.2 Safety Considerations EMC Considerations 1.3 Before You Begin Page 2.2 Front Panel Connections Figure 2.2 Input and Output Connections Table 2.2 Connectors 2.3 Electrical Installation 2.3.1 Power Connections Figure 2.3 Main Power Connections Table 2.3 Fuse Requirement (see specifications) 2.3.2 Thermocouple Input Figure 2.4 Thermocouple Wiring Hookup Table 2.4 TC Wire Color Chart 2.3.3 Two/Three/Four-Wire RTD Figure 2.5 a) RTD-1000 ohm and b) RTD-100 ohm Wiring Hookup 500 ohm Wiring Hookup Page 2.3.6 Wiring Outputs Figure 2.8 a) Mechanical Relay and SSR b) Pulse Output Outputs Wiring Hookup Wiring Hookup Figure 2.9 Isolated Analog Output Wiring Hookup Figure 2.10 Snubber Circuits Wiring Hookup Figure 2.11 Typical Applications RC CIRCUIT VARISTOR C NC NO C NC NO Page PART 3 OPERATION: Configuration Mode 3.1 Introduction Table 3.1 Button Function in Configuration Mode a b c Page 3.2.1 ID Number 3.2.2 Set Points Page Input Type (Thermocouple) Input Type (RTD) Input Type (Process) 3.2.5 Reading Configuration Menu Figure 3.4 Flow Chart for Reading Configuration Menu Page Reading Configuration (If Process was selected) Table 3.2 Conversion Table 3.2.6 Alarm 1 Figure 3.5 Flow Chart for Alarm 1 Page Page Page 3.2.7 Alarm 2 Figure 3.6 Flow Chart for Alarm 2 3.2.8 Loop Break Time/Field Calibration Figure 3.7 Flow Chart for Loop Break Time/Field Calibration Page Page Page Page Page Page Page Page 3.2.10 Analog Output (Retransmission) Figure 3.9 Flow Chart for Analog Output (Retransmission) Page 3.2.11 Ramp & Soak Figure 3.10 Flow Chart for Ramp and Soak Page 3.2.12 ID CODE Figure 3.11 Flow Chart for ID Code Page Page Page Page Page Page Page 3.2.14 DISPLAYCOLOR SELECTION Figure 3.13 Flow Chart for Display Color Selection Page Page PART 4 SPECIFICATIONS Page Page J K T E R S B C N L RTD Table 4.1 Input Properties PART 5 FACTORY PRESET VALUES Table 5.1 Factory preset value Page PART 6 CE APPROVALS INFORMATION Page Page Page Warranty/Disclaimer Return Requests/Inquiries