Manuals / Brands / Computer Equipment / Network Card / a/d/s/ / Computer Equipment / Network Card

a/d/s/ iSeries Input Type (Process), 3.2.5 Reading Configuration Menu, Figure 3.4 Flow Chart for Reading Configuration Menu

1 69

Download 69 pages, 1.03 Mb

21

Input Type (Process)

ENTER INPUT TYPE MENU:

Press a1) Press a, if necessary, until CNFGprompt appears.

Press d2) Display advance to INPT Input Menu.

Press d3) Display flashes T.ç, RTD or PROC (Thermocouple, RTD or

Process). If the displayed input type is PROC, press ato skip to

step 6 (PROC stops flashing).

PROCESS SUBMENU:

Press b4) Scroll through the available selection to PROC (flashing).

Press d5) Display shows STRD stored message momentarily and then

PROC (not flashing).

Press d6) Display flashes previous Process type selection. i.e. 0-10

(see below for Process types selection).

Press b7) Scroll through the available Process types to the selection of

your choice.

Press d8) Display shows STRD stored message and then advances to

RDG Reading Configuration Menu.

Process Types: 100 mV 1 V 10 V 0 – 20 mA

Display: 0-0.1 0-1.0 0-10 0-20

For 4-20 mAInput select 0-20 mA and adjust the Input/Reading accordingly.

To adjust 4-20 mAinput, see example under Input/Reading Submenu.

3.2.5 Reading Configuration MenuFigure 3.4 Flow Chart for Reading Configuration Menu

It is required that you put the controller in the Standby Mode for any

configuration change other than Set Points & Alarms.

Contents

Main In the U.S.A. and Canada: 1-800-NEWPORT In Mexico: (95) 800-NEWPORT Or call your local NEWPORT Office. NEWPORT Electronics,Inc. TABLE OF CONTENTS LIST OF FIGURES: LIST OF TABLES: NOTES, WARNINGS and CAUTIONS PART 1 INTRODUCTION 1.1 Description 1.2 Safety Considerations EMC Considerations 1.3 Before You Begin Page 2.2 Front Panel Connections Figure 2.2 Input and Output Connections Table 2.2 Connectors 2.3 Electrical Installation 2.3.1 Power Connections Figure 2.3 Main Power Connections Table 2.3 Fuse Requirement (see specifications) 2.3.2 Thermocouple Input Figure 2.4 Thermocouple Wiring Hookup Table 2.4 TC Wire Color Chart 2.3.3 Two/Three/Four-Wire RTD Figure 2.5 a) RTD-1000 ohm and b) RTD-100 ohm Wiring Hookup 500 ohm Wiring Hookup Page 2.3.6 Wiring Outputs Figure 2.8 a) Mechanical Relay and SSR b) Pulse Output Outputs Wiring Hookup Wiring Hookup Figure 2.9 Isolated Analog Output Wiring Hookup Figure 2.10 Snubber Circuits Wiring Hookup Figure 2.11 Typical Applications RC CIRCUIT VARISTOR C NC NO C NC NO Page PART 3 OPERATION: Configuration Mode 3.1 Introduction Table 3.1 Button Function in Configuration Mode a b c Page 3.2.1 ID Number 3.2.2 Set Points Page Input Type (Thermocouple) Input Type (RTD) Input Type (Process) 3.2.5 Reading Configuration Menu Figure 3.4 Flow Chart for Reading Configuration Menu Page Reading Configuration (If Process was selected) Table 3.2 Conversion Table 3.2.6 Alarm 1 Figure 3.5 Flow Chart for Alarm 1 Page Page Page 3.2.7 Alarm 2 Figure 3.6 Flow Chart for Alarm 2 3.2.8 Loop Break Time/Field Calibration Figure 3.7 Flow Chart for Loop Break Time/Field Calibration Page Page Page Page Page Page Page Page 3.2.10 Analog Output (Retransmission) Figure 3.9 Flow Chart for Analog Output (Retransmission) Page 3.2.11 Ramp & Soak Figure 3.10 Flow Chart for Ramp and Soak Page 3.2.12 ID CODE Figure 3.11 Flow Chart for ID Code Page Page Page Page Page Page Page 3.2.14 DISPLAYCOLOR SELECTION Figure 3.13 Flow Chart for Display Color Selection Page Page PART 4 SPECIFICATIONS Page Page J K T E R S B C N L RTD Table 4.1 Input Properties PART 5 FACTORY PRESET VALUES Table 5.1 Factory preset value Page PART 6 CE APPROVALS INFORMATION Page Page Page Warranty/Disclaimer Return Requests/Inquiries