a/d/s/ iSeries - page 41

37

RESET SETUP SUBMENU:

Press d33) Display flashes 1st digit of the previous IREST Reset value.

Press b& c34) Press band cbuttons to enter a new “Reset” value.

Press d35) Display shows STRD stored message momentarily and then

advances to RATE only, if it was changed, otherwise press ato

advance to RATE Rate Setup Submenu.

Reset unit is in seconds 0-3999.

RATE SETUPSUBMENU:

Press d36) Display flashes 1st digit of previous DRATE Rate value.

Press b& c37) Press band cbuttons to enter a new RATE value.

Press d38) Display shows STRD stored message momentarily and then

advances to the CYCL only, if it was changed, otherwise press a

to advance to CYCL Cycle Time submenu for RTD and

Thermocouple types.

Rate unit is in seconds 000.0-399.9.

CYCLE TIME SUBMENU:

Press d39) Display flashes 1st digit of the previous CYCL Cycle Time

value.

Press b& c40) Press band cbuttons to enter a new “Cycle Time” value.

(1 to 199 seconds)

Press d41) Display shows STRD stored message momentarily and then

advances to DPNG only, if it was changed, otherwise press ato

advance to DPNG Damping Factor Submenu.

ACycle Time selected between 1 and 199 seconds determines the total On/Off

time of each proportional cycle. For example, a 15 second cycle time means that

every 15 seconds the output will turn on for part or all of the cycle. For Relay

control outputs, do not select a cycle time of less than 7 seconds or the relays’

lifetime will be shortened. For a cycle time of less than 7 seconds select SSR or

DC pulse. Use an external SSR with the DC pulse option for higher currents

(higher than 1 Amp).

Contents

Main In the U.S.A. and Canada: 1-800-NEWPORT In Mexico: (95) 800-NEWPORT Or call your local NEWPORT Office. NEWPORT Electronics,Inc. TABLE OF CONTENTS LIST OF FIGURES: LIST OF TABLES: NOTES, WARNINGS and CAUTIONS PART 1 INTRODUCTION 1.1 Description 1.2 Safety Considerations EMC Considerations 1.3 Before You Begin Page 2.2 Front Panel Connections Figure 2.2 Input and Output Connections Table 2.2 Connectors 2.3 Electrical Installation 2.3.1 Power Connections Figure 2.3 Main Power Connections Table 2.3 Fuse Requirement (see specifications) 2.3.2 Thermocouple Input Figure 2.4 Thermocouple Wiring Hookup Table 2.4 TC Wire Color Chart 2.3.3 Two/Three/Four-Wire RTD Figure 2.5 a) RTD-1000 ohm and b) RTD-100 ohm Wiring Hookup 500 ohm Wiring Hookup Page 2.3.6 Wiring Outputs Figure 2.8 a) Mechanical Relay and SSR b) Pulse Output Outputs Wiring Hookup Wiring Hookup Figure 2.9 Isolated Analog Output Wiring Hookup Figure 2.10 Snubber Circuits Wiring Hookup Figure 2.11 Typical Applications RC CIRCUIT VARISTOR C NC NO C NC NO Page PART 3 OPERATION: Configuration Mode 3.1 Introduction Table 3.1 Button Function in Configuration Mode a b c Page 3.2.1 ID Number 3.2.2 Set Points Page Input Type (Thermocouple) Input Type (RTD) Input Type (Process) 3.2.5 Reading Configuration Menu Figure 3.4 Flow Chart for Reading Configuration Menu Page Reading Configuration (If Process was selected) Table 3.2 Conversion Table 3.2.6 Alarm 1 Figure 3.5 Flow Chart for Alarm 1 Page Page Page 3.2.7 Alarm 2 Figure 3.6 Flow Chart for Alarm 2 3.2.8 Loop Break Time/Field Calibration Figure 3.7 Flow Chart for Loop Break Time/Field Calibration Page Page Page Page Page Page Page Page 3.2.10 Analog Output (Retransmission) Figure 3.9 Flow Chart for Analog Output (Retransmission) Page 3.2.11 Ramp & Soak Figure 3.10 Flow Chart for Ramp and Soak Page 3.2.12 ID CODE Figure 3.11 Flow Chart for ID Code Page Page Page Page Page Page Page 3.2.14 DISPLAYCOLOR SELECTION Figure 3.13 Flow Chart for Display Color Selection Page Page PART 4 SPECIFICATIONS Page Page J K T E R S B C N L RTD Table 4.1 Input Properties PART 5 FACTORY PRESET VALUES Table 5.1 Factory preset value Page PART 6 CE APPROVALS INFORMATION Page Page Page Warranty/Disclaimer Return Requests/Inquiries