Address Setup Submenu, Address Value Submenu | a/d/s/ iSeries

TEMPERATURE UNIT SUBMENU:

Includes a byte in the data string to indicate whether reading is in Celsius or Fahrenheit.

Press d 50) Display flashes previous selection for UNIT. Press b 51) Scroll through the available selections: NO, YES.

Press d 52) Display shows STRD stored message momentarily and then advances to ADDR only, if it was changed, otherwise press a to advance to ADDR Address Setup Submenu.

ADDRESS SETUP SUBMENU:

This menu is applicable to the RS-485 Option only.

Press d 53) Display advances to “Address Value” (0000 to 0199) Submenu.

ADDRESS VALUE SUBMENU:

Press d 54) Display flashes 1st digit of previously stored Address Value. Press b & c 55) Press b and c to enter new “Address Value”.

Press d 56) Display shows STRD stored message momentarily and then advances to TR.TM only, if it was changed, otherwise press a to advance to TR.TM Transmit Time Interval Submenu.

TRANSMIT TIME INTERVAL SUBMENU:

This menu is applicable if “Continuous” Mode was selected in the “Data Flow Mode” Submenu and the device is configured as an RS-232C Standard device. Also, one or more options under the Data Format Submenu must be enabled.

Press d 57) Display advances to “Transmit Time Value” Submenu.

TRANSMIT TIME INTERVAL VALUE SUBMENU:

Determines the interval at which data will be emitted to the RS-232 Serial Bus when the instrument is in Continuous Data Flow Mode.

Press d 58) Display flashes 1st digit of previous “Transmit Time Value” in seconds.

Press b & c 59) Press b and c to enter new “Transmit Time Value”, e.g. 0030 will send the data every 30 seconds in Continuous Mode.

Press d 60) Display shows STRD stored message momentarily and then advances to COLR only, if it was changed, otherwise press a to advance to COLR Color Display Selection Menu.

For more details, refer to the Communication Manual available at the website listed on the cover page of this manual or on the CD-ROM enclosed with your shipment.

50

Image 54

a/d/s/ iSeries manual Address Setup Submenu, Address Value Submenu, Transmit Time Interval Submenu

Contents

Newport Electronics,Inc Newport Electronics,Inc Table of Contents List of Figures Flow Chart for Alarm 1 Menu Flow Chart for Alarm 2 MenuInput Properties Factory Preset Values List of Tables TIP Part Introduction Description Safety Considerations EMC Considerations Before You Begin Part Setup Optional Remote Programmer Front Panel Input PowerFront Panel Connections Output Electrical Installation Power Connections Main Power Connections Fuse Requirement see specifications Thermocouple Wiring Hookup TC Wire Color Chart Thermocouple Input 3 Two/Three/Four-Wire RTD Ohm Wiring Hookup Process Current Process Voltage Wiring Outputs Isolated Analog Output Wiring Hookup 10 Snubber Circuits Wiring Hookup 13 Excitation Output Operation Configuration Mode Introduction Button Function in Configuration ModePart Menu Configuration Flow Chart for ID and Set Points Entering Your NON-DEFAULT Full Security ID Number Entering Your NON-DEFAULT SETPOINT/ID Security ID NumberID Number Set Points Setpoint Configuration Menu Enter Configuration MenuInput Type Menu Thermocouple Submenu Input Type ThermocoupleEnter Input Type Menu Thermocouple Types RTD Types Input Type RTDRTD Submenu RTD Value Submenu Process Submenu Reading Configuration MenuInput Type Process Process Types Decimal Point Submenu Enter Reading Configuration MenuTemperature Unit Submenu Filter Constant Submenu Reading Configuration If Process was selected INPUT/READING Scale and Offset Submenu Conversion Table Range Conversion Number Alarm Enter Alarm 1 Menu Alarm 1 ENABLE/DISABLE Submenu Alarm 1 ABSOLUTE/DEVIATION SubmenuAlarm 1 LATCH/UNLATCH Submenu Contact Closure Submenu Active Submenu Alarm ENABLE/DISABLE AT Power on Alarm 1 LOW Value SubmenuAlarm 1 HI Value Submenu Enter Alarm 2 Menu Enter Loop Break Time Menu Loop Break ENABLE/DISABLE SubmenuLoop Break Time/Field Calibration Loop Break Time Value Submenu Reading Adjust Submenu Setpoint Deviation ENABLE/DISABLE SubmenuThermocouple Field Calibration Submenu Flow Chart for Output Output Enter Output 1 Menu Self SubmenuMINIMUM/PERCENT LOW Submenu MAXIMUM/PERCENT High Submenu Control Type Output Relay, SSR, or PulseAction Type Submenu Auto PID Submenu Anti Integral Submenu Start Auto Tune PID Proportional Band Submenu Reset Setup Submenu Rate Setup SubmenuCycle Time Submenu Damping Factor Submenu Deadband Submenu Analog Output Retransmission Enter Analog Output MenuCURRENT/VOLTAGE Submenu Reading OUT Ramp & Soak Ramp ENABLE/DISABLE SubmenuSoak ENABLE/DISABLE Submenu Enter Ramp and Soak Menu Ramp Value Submenu Soak Value Submenu Entering or Changing Your NON-DEFAULT ID Code ID CodeEnter ID Code Menu Entering or Changing Your Default ID Code Full Security Level SubmenuSETPOINT/ID Security Level Submenu 12 Flow Chart for Communication Option Communication Option Baud Submenu Enter Communication Option MenuCommunication Parameters Submenu Parity Submenu Modbus Protocol Submenu Stop BIT SubmenuBUS Format Submenu Line Feed Submenu Data Flow Mode Submenu Communication Interface Standard SubmenuData Separation Character Submenu Main Reading Submenu Alarm Status SubmenuData Format Submenu Peak Value Submenu Transmit Time Interval Submenu Address Setup SubmenuAddress Value Submenu Transmit Time Interval Value Submenu Enter Display Color Selection Menu Alarm 1 Display Color SubmenuDisplay Color Selection Normal Color Display Submenu Display Colors change sequences Alarm 2 Display Color SubmenuExample Green RED Amber Amber RED Green Part Specifications SSR ControlControl Output Communications Excitation InsulationGeneral Input Properties Input Type Range Accuracy Part 5 Factory Preset Values Factory preset value Display Color Colr Part CE Approvals Information Measurement CategoryPage Page Page Warranty/Disclaimer M4165/N/0206