Before You Begin | a/d/s/ iSeries specs

1.3Before You Begin

Inspecting Your Shipment:

Remove the packing slip and verify that you have received everything listed. Inspect the container and equipment for signs of damage as soon as you receive the shipment. Note any evidence of rough handling in transit. Immediately report any damage to the shipping agent. The carrier will not honor damage claims unless all shipping material is saved for inspection. After examining and removing the contents, save the packing material and carton in the event reshipment is necessary.

Customer Service:

If you need assistance, please call the nearest Customer Service Department, listed in this manual.

Manuals, Software:

The latest Operation and Communication Manual as well as free software are available from the website listed in this manual or on the CD-ROM

enclosed with your shipment.

For first-time users: Refer to the QuickStart Manual for basic operation and set-up instructions.

The following steps in this manual for configuring your device are explained by using the optional Remote Programmer Display (iDRP).

If you have the Serial Communications Option (-C24) you can easily configure the controller on your computer or on-line.

To Disable Outputs:

To ensure that menu changes are properly stored, Standby Mode should be used during setup of the instrument. During Standby Mode, the instrument remains in a ready condition, but all outputs are disabled. Standby Mode is useful when maintenence of the system is necessary.

When the instrument is in "RUN" Mode, push d twice to disable all outputs and alarms. It is now in "STANDBY" Mode. Push d once more to resume "RUN" Mode.

PUSH d TWICE to disable the system during an EMERGENCY.

To Reset the Meter:

When the controller is in the "MENU" Mode, push c once to direct controller one step backward of the top menu item.

Push c twice to reset controller, prior to resuming "Run" Mode except after "Alarms", that will go to the "Run" Mode without resetting the controller.

4

Image 8

a/d/s/ iSeries manual Before You Begin

Contents

Newport Electronics,Inc Newport Electronics,Inc Table of Contents Flow Chart for Alarm 1 Menu Flow Chart for Alarm 2 Menu Input Properties Factory Preset ValuesList of Figures List of Tables TIP Part Introduction Description Safety Considerations EMC Considerations Before You Begin Part Setup Optional Remote Programmer Front Panel Power Front Panel ConnectionsInput Output Electrical Installation Power Connections Main Power Connections Fuse Requirement see specifications Thermocouple Wiring Hookup TC Wire Color Chart Thermocouple Input 3 Two/Three/Four-Wire RTD Ohm Wiring Hookup Process Current Process Voltage Wiring Outputs Isolated Analog Output Wiring Hookup 10 Snubber Circuits Wiring Hookup 13 Excitation Output Part Operation Configuration Mode IntroductionButton Function in Configuration Mode Menu Configuration Flow Chart for ID and Set Points ID Number Entering Your NON-DEFAULT Full Security ID NumberEntering Your NON-DEFAULT SETPOINT/ID Security ID Number Set Points Setpoint Input Type Menu Configuration MenuEnter Configuration Menu Input Type Thermocouple Enter Input Type MenuThermocouple Submenu Thermocouple Types Input Type RTD RTD SubmenuRTD Types RTD Value Submenu Reading Configuration Menu Input Type ProcessProcess Submenu Process Types Enter Reading Configuration Menu Temperature Unit SubmenuDecimal Point Submenu Filter Constant Submenu Reading Configuration If Process was selected INPUT/READING Scale and Offset Submenu Conversion Table Range Conversion Number Alarm Enter Alarm 1 Menu Alarm 1 LATCH/UNLATCH Submenu Alarm 1 ENABLE/DISABLE SubmenuAlarm 1 ABSOLUTE/DEVIATION Submenu Contact Closure Submenu Active Submenu Alarm 1 HI Value Submenu Alarm ENABLE/DISABLE AT Power onAlarm 1 LOW Value Submenu Enter Alarm 2 Menu Loop Break ENABLE/DISABLE Submenu Loop Break Time/Field CalibrationEnter Loop Break Time Menu Loop Break Time Value Submenu Thermocouple Field Calibration Submenu Reading Adjust SubmenuSetpoint Deviation ENABLE/DISABLE Submenu Flow Chart for Output Output MINIMUM/PERCENT LOW Submenu Enter Output 1 MenuSelf Submenu Action Type Submenu MAXIMUM/PERCENT High SubmenuControl Type Output Relay, SSR, or Pulse Auto PID Submenu Anti Integral Submenu Start Auto Tune PID Proportional Band Submenu Cycle Time Submenu Reset Setup SubmenuRate Setup Submenu Damping Factor Submenu Deadband Submenu CURRENT/VOLTAGE Submenu Analog Output RetransmissionEnter Analog Output Menu Reading OUT Ramp ENABLE/DISABLE Submenu Soak ENABLE/DISABLE SubmenuRamp & Soak Enter Ramp and Soak Menu Ramp Value Submenu Soak Value Submenu Enter ID Code Menu Entering or Changing Your NON-DEFAULT ID CodeID Code SETPOINT/ID Security Level Submenu Entering or Changing Your Default ID CodeFull Security Level Submenu 12 Flow Chart for Communication Option Communication Option Enter Communication Option Menu Communication Parameters SubmenuBaud Submenu Parity Submenu Stop BIT Submenu BUS Format SubmenuModbus Protocol Submenu Line Feed Submenu Data Separation Character Submenu Data Flow Mode SubmenuCommunication Interface Standard Submenu Alarm Status Submenu Data Format SubmenuMain Reading Submenu Peak Value Submenu Address Setup Submenu Address Value SubmenuTransmit Time Interval Submenu Transmit Time Interval Value Submenu Alarm 1 Display Color Submenu Display Color SelectionEnter Display Color Selection Menu Normal Color Display Submenu Alarm 2 Display Color Submenu ExampleDisplay Colors change sequences Green RED Amber Amber RED Green Part Specifications Control Control OutputSSR Communications General ExcitationInsulation Input Properties Input Type Range Accuracy Part 5 Factory Preset Values Factory preset value Display Color Colr Part CE Approvals Information Measurement CategoryPage Page Page Warranty/Disclaimer M4165/N/0206