a/d/s/ iSeries - page 44

READING 1:

Press d8) Display flashes 1st digit of previous “Reading 1” value.

Press b& c9) Enter “Reading 1” value. (Example 0000).

Press d10) Display advances to OUT.1 Out 1 Submenu.

OUT 1:

Press d11) Display flashes 1st digit of previous “Out 1” value.

Press b& c12) Enter “Out 1” value. (Example 00.00).

Press d13) Display advances to RD2 Reading 2 Submenu.

READING 2:

Press d14) Display flashes 1st digit of previous “Reading 2” value.

Press b& c15) Enter “Reading 2” value. (Example 9999).

Press d16) Display advances to OUT.2 Out 2 Submenu.

OUT 2:

Press d17) Display flashes 1sttdigit of previous “Out 2” value.

Press b& c18) Enter “Out 2” value. (Example 10.00)

Press d19) Display advances to the ALR2Alarm 2 Menu.

The above example is for 0-10 V of the entire range of the Process Input

and Analog Output. For 0-20 mAoutput you need to set “Analog Type” to

Current and OUT 2 to 20.00.

Contents

Main In the U.S.A. and Canada: 1-800-NEWPORT In Mexico: (95) 800-NEWPORT Or call your local NEWPORT Office. NEWPORT Electronics,Inc. TABLE OF CONTENTS LIST OF FIGURES: LIST OF TABLES: NOTES, WARNINGS and CAUTIONS PART 1 INTRODUCTION 1.1 Description 1.2 Safety Considerations EMC Considerations 1.3 Before You Begin Page 2.2 Front Panel Connections Figure 2.2 Input and Output Connections Table 2.2 Connectors 2.3 Electrical Installation 2.3.1 Power Connections Figure 2.3 Main Power Connections Table 2.3 Fuse Requirement (see specifications) 2.3.2 Thermocouple Input Figure 2.4 Thermocouple Wiring Hookup Table 2.4 TC Wire Color Chart 2.3.3 Two/Three/Four-Wire RTD Figure 2.5 a) RTD-1000 ohm and b) RTD-100 ohm Wiring Hookup 500 ohm Wiring Hookup Page 2.3.6 Wiring Outputs Figure 2.8 a) Mechanical Relay and SSR b) Pulse Output Outputs Wiring Hookup Wiring Hookup Figure 2.9 Isolated Analog Output Wiring Hookup Figure 2.10 Snubber Circuits Wiring Hookup Figure 2.11 Typical Applications RC CIRCUIT VARISTOR C NC NO C NC NO Page PART 3 OPERATION: Configuration Mode 3.1 Introduction Table 3.1 Button Function in Configuration Mode a b c Page 3.2.1 ID Number 3.2.2 Set Points Page Input Type (Thermocouple) Input Type (RTD) Input Type (Process) 3.2.5 Reading Configuration Menu Figure 3.4 Flow Chart for Reading Configuration Menu Page Reading Configuration (If Process was selected) Table 3.2 Conversion Table 3.2.6 Alarm 1 Figure 3.5 Flow Chart for Alarm 1 Page Page Page 3.2.7 Alarm 2 Figure 3.6 Flow Chart for Alarm 2 3.2.8 Loop Break Time/Field Calibration Figure 3.7 Flow Chart for Loop Break Time/Field Calibration Page Page Page Page Page Page Page Page 3.2.10 Analog Output (Retransmission) Figure 3.9 Flow Chart for Analog Output (Retransmission) Page 3.2.11 Ramp & Soak Figure 3.10 Flow Chart for Ramp and Soak Page 3.2.12 ID CODE Figure 3.11 Flow Chart for ID Code Page Page Page Page Page Page Page 3.2.14 DISPLAYCOLOR SELECTION Figure 3.13 Flow Chart for Display Color Selection Page Page PART 4 SPECIFICATIONS Page Page J K T E R S B C N L RTD Table 4.1 Input Properties PART 5 FACTORY PRESET VALUES Table 5.1 Factory preset value Page PART 6 CE APPROVALS INFORMATION Page Page Page Warranty/Disclaimer Return Requests/Inquiries