a/d/s/ iSeries - page 57

Example 3:

Output 1: Relay, Setpoint 1: 200

Alarm 2: Relay, Setpoint 2: 200

Alarm 1 Setup: Deviation, Band, “ALR.H” = 20

Alarm 2 Setup: Deviation, Hi/Low, “ALR.H” = 10, “ALR.L” = 5

Color Display Setup: “N.CLR” = Green, “1.CLR” = Amber, “2.CLR” = Red

Display colors change sequences:

AMBER RED GREEN GREEN RED AMBER

•--➤---------------•----------------•-------------•--------------•-------------•---------------------➤

0 180 195 200 210 220

Reset: The instrument automatically resets after the last menu of the

Configuration Mode has been entered. After the instrument resets, it

advances to the Run Mode.

Contents

Main In the U.S.A. and Canada: 1-800-NEWPORT In Mexico: (95) 800-NEWPORT Or call your local NEWPORT Office. NEWPORT Electronics,Inc. TABLE OF CONTENTS LIST OF FIGURES: LIST OF TABLES: NOTES, WARNINGS and CAUTIONS PART 1 INTRODUCTION 1.1 Description 1.2 Safety Considerations EMC Considerations 1.3 Before You Begin Page 2.2 Front Panel Connections Figure 2.2 Input and Output Connections Table 2.2 Connectors 2.3 Electrical Installation 2.3.1 Power Connections Figure 2.3 Main Power Connections Table 2.3 Fuse Requirement (see specifications) 2.3.2 Thermocouple Input Figure 2.4 Thermocouple Wiring Hookup Table 2.4 TC Wire Color Chart 2.3.3 Two/Three/Four-Wire RTD Figure 2.5 a) RTD-1000 ohm and b) RTD-100 ohm Wiring Hookup 500 ohm Wiring Hookup Page 2.3.6 Wiring Outputs Figure 2.8 a) Mechanical Relay and SSR b) Pulse Output Outputs Wiring Hookup Wiring Hookup Figure 2.9 Isolated Analog Output Wiring Hookup Figure 2.10 Snubber Circuits Wiring Hookup Figure 2.11 Typical Applications RC CIRCUIT VARISTOR C NC NO C NC NO Page PART 3 OPERATION: Configuration Mode 3.1 Introduction Table 3.1 Button Function in Configuration Mode a b c Page 3.2.1 ID Number 3.2.2 Set Points Page Input Type (Thermocouple) Input Type (RTD) Input Type (Process) 3.2.5 Reading Configuration Menu Figure 3.4 Flow Chart for Reading Configuration Menu Page Reading Configuration (If Process was selected) Table 3.2 Conversion Table 3.2.6 Alarm 1 Figure 3.5 Flow Chart for Alarm 1 Page Page Page 3.2.7 Alarm 2 Figure 3.6 Flow Chart for Alarm 2 3.2.8 Loop Break Time/Field Calibration Figure 3.7 Flow Chart for Loop Break Time/Field Calibration Page Page Page Page Page Page Page Page 3.2.10 Analog Output (Retransmission) Figure 3.9 Flow Chart for Analog Output (Retransmission) Page 3.2.11 Ramp & Soak Figure 3.10 Flow Chart for Ramp and Soak Page 3.2.12 ID CODE Figure 3.11 Flow Chart for ID Code Page Page Page Page Page Page Page 3.2.14 DISPLAYCOLOR SELECTION Figure 3.13 Flow Chart for Display Color Selection Page Page PART 4 SPECIFICATIONS Page Page J K T E R S B C N L RTD Table 4.1 Input Properties PART 5 FACTORY PRESET VALUES Table 5.1 Factory preset value Page PART 6 CE APPROVALS INFORMATION Page Page Page Warranty/Disclaimer Return Requests/Inquiries