Entering or Changing Your Default ID Code | a/d/s/ iSeries specs

ENTERING OR CHANGING YOUR (DEFAULT) ID CODE:

Enter ID menu (Repeat steps from 1 to 3).

Press d 10) Display advances to CH.ID Change ID Code Submenu. Press d 11) Display shows 0000 message with flashing 1st digit.

If you want to change your default “ID Code” you can do it now, otherwise press a and menu will skip to FULL Full Security Submenu.

Press b & c 12) Press b and c buttons to enter your new “ID Code” number. Press d 13) Display shows STRD stored message momentarily and then

advances to the FULL Full Security Submenu.

FULL SECURITY LEVEL SUBMENU:

Press	d	14)	Display flashes ENBL Enable or DSBL Disable.
Press	b	15) Scroll through the available selections: “Enable” or “Disable”.
Press d		16)	Display shows STRD stored message momentarily and then
		advances to SP.ID Setpoint/ID Submenu.
		If "Full" Security Level is "Enabled" and the user attempts to
		enter the Main Menu, they will be prompted for an ID Code. The

		ID Code should be correct to enter the instrument Menu item.
SETPOINT/ID SECURITY LEVEL SUBMENU:
		This Security Level can be functional only if FULL Security
		Level is Disabled.
		Level is Disabled.
Press	d	17)	Display flashes ENBL Enable or DSBL Disable.
Press	b	18) Scroll through the available selections: “Enable” or “Disable”.
Press d		19)	Display shows STRD stored message momentarily and then
		advances to COMM Communication Submenu.

If "Setpoint/ID" Security Level is "Enabled" and the user attempts to advance into the CNFG Configuration Menu, he will be prompted for ID Code number. The ID Code should be correct to proceed into the Configuration Menu, otherwise display will show an Error and skip to the Run Mode.

If “Full” and “Setpoint/ID” Security Levels are "Disabled", the ID code will be “Disabled” and user will not be asked for ID Code to enter the Menu items (“ID” Submenu will not show up in “ID/Setpoint” Menu).

44

Image 48

a/d/s/ iSeries Entering or Changing Your Default ID Code, Full Security Level Submenu, SETPOINT/ID Security Level Submenu

Contents

Newport Electronics,Inc Newport Electronics,Inc Table of Contents Flow Chart for Alarm 1 Menu Flow Chart for Alarm 2 Menu Input Properties Factory Preset ValuesList of Figures List of Tables TIP Part Introduction Description Safety Considerations EMC Considerations Before You Begin Part Setup Optional Remote Programmer Front Panel Power Front Panel ConnectionsInput Output Electrical Installation Power Connections Main Power Connections Fuse Requirement see specifications Thermocouple Wiring Hookup TC Wire Color Chart Thermocouple Input 3 Two/Three/Four-Wire RTD Ohm Wiring Hookup Process Current Process Voltage Wiring Outputs Isolated Analog Output Wiring Hookup 10 Snubber Circuits Wiring Hookup 13 Excitation Output Operation Configuration Mode Introduction Button Function in Configuration ModePart Menu Configuration Flow Chart for ID and Set Points Entering Your NON-DEFAULT Full Security ID Number Entering Your NON-DEFAULT SETPOINT/ID Security ID NumberID Number Set Points Setpoint Configuration Menu Enter Configuration MenuInput Type Menu Input Type Thermocouple Enter Input Type MenuThermocouple Submenu Thermocouple Types Input Type RTD RTD SubmenuRTD Types RTD Value Submenu Reading Configuration Menu Input Type ProcessProcess Submenu Process Types Enter Reading Configuration Menu Temperature Unit SubmenuDecimal Point Submenu Filter Constant Submenu Reading Configuration If Process was selected INPUT/READING Scale and Offset Submenu Conversion Table Range Conversion Number Alarm Enter Alarm 1 Menu Alarm 1 ENABLE/DISABLE Submenu Alarm 1 ABSOLUTE/DEVIATION SubmenuAlarm 1 LATCH/UNLATCH Submenu Contact Closure Submenu Active Submenu Alarm ENABLE/DISABLE AT Power on Alarm 1 LOW Value SubmenuAlarm 1 HI Value Submenu Enter Alarm 2 Menu Loop Break ENABLE/DISABLE Submenu Loop Break Time/Field CalibrationEnter Loop Break Time Menu Loop Break Time Value Submenu Reading Adjust Submenu Setpoint Deviation ENABLE/DISABLE SubmenuThermocouple Field Calibration Submenu Flow Chart for Output Output Enter Output 1 Menu Self SubmenuMINIMUM/PERCENT LOW Submenu MAXIMUM/PERCENT High Submenu Control Type Output Relay, SSR, or PulseAction Type Submenu Auto PID Submenu Anti Integral Submenu Start Auto Tune PID Proportional Band Submenu Reset Setup Submenu Rate Setup SubmenuCycle Time Submenu Damping Factor Submenu Deadband Submenu Analog Output Retransmission Enter Analog Output MenuCURRENT/VOLTAGE Submenu Reading OUT Ramp ENABLE/DISABLE Submenu Soak ENABLE/DISABLE SubmenuRamp & Soak Enter Ramp and Soak Menu Ramp Value Submenu Soak Value Submenu Entering or Changing Your NON-DEFAULT ID Code ID CodeEnter ID Code Menu Entering or Changing Your Default ID Code Full Security Level SubmenuSETPOINT/ID Security Level Submenu 12 Flow Chart for Communication Option Communication Option Enter Communication Option Menu Communication Parameters SubmenuBaud Submenu Parity Submenu Stop BIT Submenu BUS Format SubmenuModbus Protocol Submenu Line Feed Submenu Data Flow Mode Submenu Communication Interface Standard SubmenuData Separation Character Submenu Alarm Status Submenu Data Format SubmenuMain Reading Submenu Peak Value Submenu Address Setup Submenu Address Value SubmenuTransmit Time Interval Submenu Transmit Time Interval Value Submenu Alarm 1 Display Color Submenu Display Color SelectionEnter Display Color Selection Menu Normal Color Display Submenu Alarm 2 Display Color Submenu ExampleDisplay Colors change sequences Green RED Amber Amber RED Green Part Specifications Control Control OutputSSR Communications Excitation InsulationGeneral Input Properties Input Type Range Accuracy Part 5 Factory Preset Values Factory preset value Display Color Colr Part CE Approvals Information Measurement CategoryPage Page Page Warranty/Disclaimer M4165/N/0206