a/d/s/ iSeries - page 26

22

ENTER READING CONFIGURATION MENU:

Press a1) Press a, if necessary, until CNFGprompt appears.

Press d2) Display advances to INPT Input Menu.

Press a3) Display advances to RDG Reading Configuration Menu.

Press d4) Display advances to DEC Decimal Point.

DECIMAL POINT SUBMENU:

Press d5) Display flashes previous selection for Decimal location.

Press b6) Scroll though the available selections and choose Decimal

location: FFFF or FFF.F (also FF.FF and F.FFF — if PROC

Process type was selected in the Input Type Menu).

Press d7) Display shows STRD stored message momentarily and then

advances to TEMP Temperature Unit.

Decimal Point for Process Input Type is passive.

TEMPERATURE UNIT SUBMENU:

Press d8) Display flashes previous Temperature Unit selection.

Press b9) Scroll though the available selections to the Temperature Unit

of your choice: °F or °C.

Press d10) Display shows STRD stored message momentarily and then

advances to FLTR Filter Constant.

FILTER CONSTANT SUBMENU:

Press d11) Display flashes previous selection for Filter Constant.

Press b12) Scroll though the available selections: 0001,0002,0004,

0008,0016,0032,0064,0128. - Default is 0004

Press d13) Display shows STRD stored message momentarily only, if a

change was made, otherwise press ato advance to the next menu.

If Process was selected in the Input Type Menu the display will

advance to IN.RD Input/Reading Submenu, otherwise the

display advances to the ALR1Alarm 1 Menu.

The Filter Constant Submenu allows the user to specify the

number of readings stored in the Digital Averaging Filter.

For PID control select filter value 0001-0004. Afilter value of 2 is

approximately equal to 1 second RC low pass time constant.

Contents

Main In the U.S.A. and Canada: 1-800-NEWPORT In Mexico: (95) 800-NEWPORT Or call your local NEWPORT Office. NEWPORT Electronics,Inc. TABLE OF CONTENTS LIST OF FIGURES: LIST OF TABLES: NOTES, WARNINGS and CAUTIONS PART 1 INTRODUCTION 1.1 Description 1.2 Safety Considerations EMC Considerations 1.3 Before You Begin Page 2.2 Front Panel Connections Figure 2.2 Input and Output Connections Table 2.2 Connectors 2.3 Electrical Installation 2.3.1 Power Connections Figure 2.3 Main Power Connections Table 2.3 Fuse Requirement (see specifications) 2.3.2 Thermocouple Input Figure 2.4 Thermocouple Wiring Hookup Table 2.4 TC Wire Color Chart 2.3.3 Two/Three/Four-Wire RTD Figure 2.5 a) RTD-1000 ohm and b) RTD-100 ohm Wiring Hookup 500 ohm Wiring Hookup Page 2.3.6 Wiring Outputs Figure 2.8 a) Mechanical Relay and SSR b) Pulse Output Outputs Wiring Hookup Wiring Hookup Figure 2.9 Isolated Analog Output Wiring Hookup Figure 2.10 Snubber Circuits Wiring Hookup Figure 2.11 Typical Applications RC CIRCUIT VARISTOR C NC NO C NC NO Page PART 3 OPERATION: Configuration Mode 3.1 Introduction Table 3.1 Button Function in Configuration Mode a b c Page 3.2.1 ID Number 3.2.2 Set Points Page Input Type (Thermocouple) Input Type (RTD) Input Type (Process) 3.2.5 Reading Configuration Menu Figure 3.4 Flow Chart for Reading Configuration Menu Page Reading Configuration (If Process was selected) Table 3.2 Conversion Table 3.2.6 Alarm 1 Figure 3.5 Flow Chart for Alarm 1 Page Page Page 3.2.7 Alarm 2 Figure 3.6 Flow Chart for Alarm 2 3.2.8 Loop Break Time/Field Calibration Figure 3.7 Flow Chart for Loop Break Time/Field Calibration Page Page Page Page Page Page Page Page 3.2.10 Analog Output (Retransmission) Figure 3.9 Flow Chart for Analog Output (Retransmission) Page 3.2.11 Ramp & Soak Figure 3.10 Flow Chart for Ramp and Soak Page 3.2.12 ID CODE Figure 3.11 Flow Chart for ID Code Page Page Page Page Page Page Page 3.2.14 DISPLAYCOLOR SELECTION Figure 3.13 Flow Chart for Display Color Selection Page Page PART 4 SPECIFICATIONS Page Page J K T E R S B C N L RTD Table 4.1 Input Properties PART 5 FACTORY PRESET VALUES Table 5.1 Factory preset value Page PART 6 CE APPROVALS INFORMATION Page Page Page Warranty/Disclaimer Return Requests/Inquiries