a/d/s/ iSeries - page 50

46

ENTER COMMUNICATION OPTION MENU:

Press a1) Press a, if necessary, until CNFGprompt appears.

Press d2) Display advances to INPT Input Menu.

Press a3) Press a, if necessary, until Display advances to COMM

Communication Options Menu.

Press d4) Display advances to C.PAR Communication Parameters

Submenu.

If Communication Option is not installed, the display shows

NONE and skips to the Color Display Menu.

COMMUNICATION PARAMETERS SUBMENU:

Allows the user to adjust Serial Communications Settings of the instrument.

When connecting an instrument to a computer or other device, the

Communications Parameters must match. Generally the default settings

(as shown in Section 5) should be utilized.

Press d5) Display advances to BAUD Baud Submenu.

BAUD SUBMENU:

Press d6) Display flashes previous selection for BAUD value.

Press b7) Scroll through the available selections: 300_, 600_, 1200,

2400, 4800, 9600, 19.2K.

Press d8) Display shows STRD stored message momentarily and then

advances to PRTY only, if it was changed, otherwise press ato

advance to PRTY Parity Submenu.

PARITYSUBMENU:

Press d9) Display flashes previous selection for “Parity”.

Press b10) Scroll through the available selections: NO, ODD, EVEN.

Press d11) Display shows STRD stored message momentarily and then

advances to DATA only, if it was changed, otherwise press ato

advance to DATA Data Bit Submenu.

DATABIT SUBMENU:

Press d12) Display flashes previous selection for “Data Bit”.

Press b13) Scroll through the available selections: 7-BIT, 8-BIT.

Press d14) Display shows STRD stored message and then advances to

STOP only, if it was changed, otherwise press ato advance to

STOP Stop Bit Submenu.

Contents

Main In the U.S.A. and Canada: 1-800-NEWPORT In Mexico: (95) 800-NEWPORT Or call your local NEWPORT Office. NEWPORT Electronics,Inc. TABLE OF CONTENTS LIST OF FIGURES: LIST OF TABLES: NOTES, WARNINGS and CAUTIONS PART 1 INTRODUCTION 1.1 Description 1.2 Safety Considerations EMC Considerations 1.3 Before You Begin Page 2.2 Front Panel Connections Figure 2.2 Input and Output Connections Table 2.2 Connectors 2.3 Electrical Installation 2.3.1 Power Connections Figure 2.3 Main Power Connections Table 2.3 Fuse Requirement (see specifications) 2.3.2 Thermocouple Input Figure 2.4 Thermocouple Wiring Hookup Table 2.4 TC Wire Color Chart 2.3.3 Two/Three/Four-Wire RTD Figure 2.5 a) RTD-1000 ohm and b) RTD-100 ohm Wiring Hookup 500 ohm Wiring Hookup Page 2.3.6 Wiring Outputs Figure 2.8 a) Mechanical Relay and SSR b) Pulse Output Outputs Wiring Hookup Wiring Hookup Figure 2.9 Isolated Analog Output Wiring Hookup Figure 2.10 Snubber Circuits Wiring Hookup Figure 2.11 Typical Applications RC CIRCUIT VARISTOR C NC NO C NC NO Page PART 3 OPERATION: Configuration Mode 3.1 Introduction Table 3.1 Button Function in Configuration Mode a b c Page 3.2.1 ID Number 3.2.2 Set Points Page Input Type (Thermocouple) Input Type (RTD) Input Type (Process) 3.2.5 Reading Configuration Menu Figure 3.4 Flow Chart for Reading Configuration Menu Page Reading Configuration (If Process was selected) Table 3.2 Conversion Table 3.2.6 Alarm 1 Figure 3.5 Flow Chart for Alarm 1 Page Page Page 3.2.7 Alarm 2 Figure 3.6 Flow Chart for Alarm 2 3.2.8 Loop Break Time/Field Calibration Figure 3.7 Flow Chart for Loop Break Time/Field Calibration Page Page Page Page Page Page Page Page 3.2.10 Analog Output (Retransmission) Figure 3.9 Flow Chart for Analog Output (Retransmission) Page 3.2.11 Ramp & Soak Figure 3.10 Flow Chart for Ramp and Soak Page 3.2.12 ID CODE Figure 3.11 Flow Chart for ID Code Page Page Page Page Page Page Page 3.2.14 DISPLAYCOLOR SELECTION Figure 3.13 Flow Chart for Display Color Selection Page Page PART 4 SPECIFICATIONS Page Page J K T E R S B C N L RTD Table 4.1 Input Properties PART 5 FACTORY PRESET VALUES Table 5.1 Factory preset value Page PART 6 CE APPROVALS INFORMATION Page Page Page Warranty/Disclaimer Return Requests/Inquiries