Activating the Raven, Automatic Activation | Airlink X EV-DO

CHAPTER 2

Activating the Raven X

Your Raven X needs specific parameters before it can operate on the EV-DO network.

Automatic Activation

One of the special features of your Raven X EV-DO and the Verizon network is the ability to acti- vate itself automatically. When you first power on the Raven X, the modem will check to see if it has been activated with account data. If it finds that it has not yet been activated, it will attempt to retrieve the account data from the Verizon network using Over-the-Air Service Provisioning (OTASP).

Note: You need to have an account with before you attempt automatic activation. If you have not ordered an account from for your Raven X, it will not succeed at activating itself.

Attach the antenna to your modem before you plug in the power.

1.The Raven X will cycle the LED lights in its power on self test.

2.All the lights will go out except the power light. At this point, the modem is attempting to download its account information. The download process may take about a minute or two.

3.When the download is complete, the Raven X will reset itself, the power light will go out and the LED lights will cycle once more.

4.When the Network light illuminates, your Raven X has successfully completed OTASP and is registered on the Verizon network.

.If you need to update the ALEOS firmware, change the account information, or want to test your Raven X’s account settings, you can use the Setup Wizard. If the automatic activation was suc- cessful, you do not need to do anything additional to activate your Raven X for Verizon.

Caution: Before you power up the the first time, be sure to have the antenna con- nected. Do not move your while it is being programmed.

Quick Start Guide and Setup Wizard

A quick and easy way to activate and configure your Raven X to connect to the cellular network is via the AirLink Setup Wizard for Verizon. The Quick Start Guide will lead you through using the Setup Wizard.

Raven X EV-DO for Verizon - User Guide, version 2.34

5

Image 11

Airlink X EV-DO manual Activating the Raven, Automatic Activation, Quick Start Guide and Setup Wizard

Contents

Version 2.34 April Raven X EV-DO Raven X EV-DO for Verizon User Guide, version Contents Contents Modbus/BSAP Configuration Simple Network Management Protocol Snmp Frequently Asked Questions and Technical Support EV-DO Overview Introduction to Raven X EV-DO Steps of a connection Establishing an Internet ConnectionIntroduction to Raven X EV-DO Dynamic vs. Static IP Addresses Using Your Raven X to Connect to the Internet Common Uses for the Raven Backup connection to the Internet Automatic Activation Quick Start Guide and Setup WizardActivating the Raven Activating the Raven Activating the Raven X using AT Commands AceView Utilities for the Raven Utilities for the Raven Wireless Ace AceNet AceNet Modem Doctor Modem Doctor Reasons to contact the modem and/or the connected device IP Manager and DNS IP Manager and DNS Fully Qualified Domain Name Dynamic Names Wireless Ace Dynamic IP Eairlink.com Data Usage for IP Manager Server UpdatesRestrictions for Modem Name Configuring DNS DNS Using Names Instead of IP addresses PPP-Peer Data Communication and Host Modes Data Communication and Host Modes AT Mode Wireless Ace PassThru PassThru Mode TelnetMode Wireless Ace Telnet Configuration Wireless Ace PPP/Ethernet PPP Mode UDP Auto Answer Slip ModeUDP Pad Reliable UDP UDP Multicast Mode Hybrid Modes TCP PAD Internal Dhcp Server Public and Private Mode PPPoE with Dhcp Dhcp in the Raven X using Public ModeAirLink Modem as a Gateway Dhcp and Routing Keepalive Configuring Keepalive Data usage using Keepalive Remote Terminal Unit RTU Modbus/BSAP ConfigurationModbus Overview Telemetry Modbus TCP/IP Modbus/BSAP ConfigurationSupervisory Control and Data Acquisition Scada Programmable Logic Controller PLC Configuring the Raven X at the Polling Host for Modbus on Configuring the Raven Wireless Ace Device Port Dynamic IP Wireless Ace Addr List Configuring the Remote Modems for Modbus with UDP Dynamic IPs Wireless Ace UDP Power-up Mode Raven mounted in an enclosure with an RTU Power Connections Connecting the Antennas Hardware Installation Hardware Installation Connecting PowerConnecting the Raven X to a computer or other device Raven X Indicator Lights Light Patterns Monitoring Power-In Voltage and Internal Temperature Wireless Ace *POWERIN and *BOARDTEMP Built in Mounting Tabs for Raven Modem Placement Modem Placement Installing a Raven with an RTU Raven mounted in an enclosure with RTU Data Services & RF Features Specifications for the Raven X EV-DOPhysical Characteristics Environmental Specifications for the Raven X EV-DOPower Management Power consumption Using Wireless Ace AT Commands Wireless Ace Save / Load a Template AT Commands StartAll ProgramsAccessoriesCommunicationsHyperTerminal Using Telnet Terminal Emulation Direct Serial Connection HyperTerminal Comport Setting HyperTerminal Comport Settings Using AT Commands with a Terminal Application Symbols AT Command Listing Information and Status AT Commands Information and Status Autoprl ETHMAC? Prlstatus Bad Password Count OPRG=n AT Commands Misc MiscellaneousMisc Miscellaneous NETPW=pw DPORT=nHOSTPAP=n NETALLOWZEROIP=n STATUSCHK=n PRLDIAL=nSTATICIP=d.d.d.d +++ AT Commands SerialSerial Dmethodd.d.d.d/ppppp or Dmethod@name/ppppp S23=speed,databitsparitystop bits PPPNOCARRIER=n Set DTR mode S60=n AT Commands TCPS0=n S7=n ENQ=n S221=nTCPS=n TCPT=n MDhh AT Commands UDPAIP=n HOR=n UALL=n S82=nS83=n DU=n UDPLAST=n DNSUSER=d.d.d.d AT Commands DNSDNSUPDATE=n DNSn IPMANAGERn=name AT Commands Dynamic IPDOMAIN=name MODEMNAME=name IPMGRUPDATEn=mIPMGRKEYn=key PPP/Ethernet AT Commands PPP/Ethernet HOSTUID=string HOSTPRIVMODE=nHOSTPW=string PassThru AT Commands PassThru \APASSTHRU Smtp including SMS AT Commands Smtp including SMS NETSMS2EMAIL=n SMTPSEND=emailbody DATZ=n AT Commands OtherOther DAE=n NETWDOG=n IPPING=nMSCIUPDADDR=name/port MSCIUPDPERIOD=n SNTP=n TELNETTIMEOUT=nSNMPSECLVL=n SNMPTRAPDEST=host/port FM=n AT Commands FriendsFriends 255 = allow any number Logging AT Commands Logging DBGPPPLVL=n Telemetry and Addr List Address List AT Commands Telemetry and Addr List Address List MVLEN=n IPL=n MVTYP=n MVMSK=hhMVOFF=n MVOPT=n MDn Commands in other groups associtated with Telemetry Destination Port and *DPORT Destination Address ~NAMLCK=nnnnnn AT Commands CDMA/EV-DO+CTA=n $QCMIP=n PROVISION=MSL,MDN/MIN,SID,NID EVDODIVERSITY=n Nam=0 Snmp Traps Raven X Snmp ConfigurationSnmp Overview Management Information Base MIB Security Level User Name and PasswordSimple Network Management Protocol Snmp Listening Port Community String Snmp MIB Definition for AirLinkTrap Destination Imports Simple Network Management Protocol Snmp Simple Network Management Protocol Snmp 100 101 102 103 PPPoE PPP over Ethernet ConfigurationConfiguring your Raven X for PPPoE PPPoE Point to Point Protocol over Ethernet 104 PPPoE Point to Point Protocol over Ethernet 105 Configuring a PPPoE Connection in Windows Show All Connections 106 107 PPPoE 108 Select Finish to exit the Network Connection Wizard 109 Connect 110 111 Connecting to the Internet with PPPoE 112 Configuring your router for PPPoE with the Raven 113 Installing the Modem Driver in Microsoft WindowsWindows Dial-up Networking DUN 114 Windows Dial-up Networking DUN Modem Driver 115 116 Dial-Up Networking PPP Configuration for Microsoft Windows 117 118 Phone Number 119 120 121 Modem Configuration 122 Establishing a DUN Connection using AceViewMaking a DUN Connection 123 Windows 98 and Windows NTEstablishing a DUN Connection with Windows Networking 124 125 Warranty Terms and ConditionsWarranty Terms 126 Warranty ConditionsWarranty Terms and Conditions Remedy 127 General Conditions 128 Frequently Asked Questions and Technical SupportFAQ Topics What Type of Antenna is Best for my Raven X? Frequently Asked Questions and Technical SupportWhat is RSSI? Why is the Rssi for my Raven X negative? What is the Proper RF Coverage for my Raven X? 130 What do I need to power my Raven X ?Can I use a portable battery to power my Raven X ? 131 What is the difference between Private and Public mode?Raven X’s IP Addresses and Local Networking Software Required 132 133 Security for the RavenDoes EV-DO provide any security? 134 Wireless Ace Reset Password 135 Activation Registering on the Verizon Network 136 Using Aleos 137 What is a PRL?How can I update the PRL Prefered Roaming List? Prefered Roaming List PRL 138 Terminal Connection AT Commands Contacting Technical Support AirLink Technical SupportAirLink Technical Support AirLink Support Web Site AirLink Documentation and Guides