AT Commands UDP, AIP=n, HOR=n, MDhh | Airlink X EV-DO specs

AT Commands: UDP

UDP

This group includes commands specific to UDP communications.

FIGURE 1. Common : UDP

AIP=n

Allow IP address.

n=0 Allow only the IP address specified in S53 to connect when UDP auto answer is enabled (S82=2). n=1 Allow any incoming IP address to connect when UDP auto answer is enabled (S82=2).

Note: Always subject to any Friends filters that may be defined.

HOR=n

Half-Open Response - In UDP auto answer (half-open) mode:

n=0 No response codes when UDP session is initiated.

n=1 RING CONNECT response codes sent out serial link before the data from the first UDP packet. Note: Quiet Mode must be Off.

MDhh

Default power-up mode for the serial port.

When the Raven X is power-cycled, the serial port enters the mode specified by this command after 5 seconds. On startup, typing ATMD0 within 5 seconds changes the mode to normal (AT command) mode.

hh (hex byte)=00 : normal mode

Raven X EV-DO for Verizon - User Guide, version 2.34

67

Image 73

Airlink X EV-DO manual AT Commands UDP, AIP=n, HOR=n, MDhh

Contents

Version 2.34 April Raven X EV-DO Raven X EV-DO for Verizon User Guide, version Contents Contents Modbus/BSAP Configuration Simple Network Management Protocol Snmp Frequently Asked Questions and Technical Support EV-DO Overview Introduction to Raven X EV-DO Introduction to Raven X EV-DO Establishing an Internet ConnectionSteps of a connection Dynamic vs. Static IP Addresses Using Your Raven X to Connect to the Internet Common Uses for the Raven Backup connection to the Internet Activating the Raven Quick Start Guide and Setup WizardAutomatic Activation Activating the Raven Activating the Raven X using AT Commands AceView Utilities for the Raven Utilities for the Raven Wireless Ace AceNet AceNet Modem Doctor Modem Doctor Reasons to contact the modem and/or the connected device IP Manager and DNS IP Manager and DNS Fully Qualified Domain Name Dynamic Names Wireless Ace Dynamic IP Restrictions for Modem Name Data Usage for IP Manager Server UpdatesEairlink.com Configuring DNS DNS Using Names Instead of IP addresses PPP-Peer Data Communication and Host Modes Data Communication and Host Modes AT Mode Wireless Ace PassThru PassThru Mode TelnetMode Wireless Ace Telnet Configuration Wireless Ace PPP/Ethernet PPP Mode UDP Pad Slip ModeUDP Auto Answer Reliable UDP UDP Multicast Mode Hybrid Modes TCP PAD Internal Dhcp Server Public and Private Mode AirLink Modem as a Gateway Dhcp in the Raven X using Public ModeDhcp and Routing PPPoE with Dhcp Keepalive Configuring Keepalive Data usage using Keepalive Modbus Overview Modbus/BSAP ConfigurationTelemetry Remote Terminal Unit RTU Supervisory Control and Data Acquisition Scada Modbus/BSAP ConfigurationProgrammable Logic Controller PLC Modbus TCP/IP Configuring the Raven X at the Polling Host for Modbus on Configuring the Raven Wireless Ace Device Port Dynamic IP Wireless Ace Addr List Configuring the Remote Modems for Modbus with UDP Dynamic IPs Wireless Ace UDP Power-up Mode Raven mounted in an enclosure with an RTU Power Connections Connecting the Antennas Hardware Installation Connecting the Raven X to a computer or other device Connecting PowerRaven X Indicator Lights Hardware Installation Light Patterns Monitoring Power-In Voltage and Internal Temperature Wireless Ace *POWERIN and *BOARDTEMP Built in Mounting Tabs for Raven Modem Placement Modem Placement Installing a Raven with an RTU Raven mounted in an enclosure with RTU Physical Characteristics Specifications for the Raven X EV-DOData Services & RF Features Power Management Specifications for the Raven X EV-DOPower consumption Environmental Using Wireless Ace AT Commands Wireless Ace Save / Load a Template AT Commands StartAll ProgramsAccessoriesCommunicationsHyperTerminal Using Telnet Terminal Emulation Direct Serial Connection HyperTerminal Comport Setting HyperTerminal Comport Settings Using AT Commands with a Terminal Application Symbols AT Command Listing Information and Status AT Commands Information and Status Autoprl ETHMAC? Prlstatus Bad Password Count Misc Miscellaneous AT Commands Misc MiscellaneousOPRG=n HOSTPAP=n DPORT=nNETALLOWZEROIP=n NETPW=pw STATICIP=d.d.d.d PRLDIAL=nSTATUSCHK=n Serial AT Commands Serial+++ Dmethodd.d.d.d/ppppp or Dmethod@name/ppppp S23=speed,databitsparitystop bits PPPNOCARRIER=n Set DTR mode S0=n AT Commands TCPS7=n S60=n TCPS=n S221=nTCPT=n ENQ=n AIP=n AT Commands UDPHOR=n MDhh S83=n S82=nDU=n UALL=n UDPLAST=n DNSUPDATE=n AT Commands DNSDNSn DNSUSER=d.d.d.d DOMAIN=name AT Commands Dynamic IPIPMANAGERn=name IPMGRKEYn=key IPMGRUPDATEn=mMODEMNAME=name PPP/Ethernet AT Commands PPP/Ethernet HOSTPW=string HOSTPRIVMODE=nHOSTUID=string PassThru AT Commands PassThru \APASSTHRU Smtp including SMS AT Commands Smtp including SMS NETSMS2EMAIL=n SMTPSEND=emailbody Other AT Commands OtherDAE=n DATZ=n MSCIUPDADDR=name/port IPPING=nMSCIUPDPERIOD=n NETWDOG=n SNMPSECLVL=n TELNETTIMEOUT=nSNMPTRAPDEST=host/port SNTP=n Friends AT Commands FriendsFM=n 255 = allow any number Logging AT Commands Logging DBGPPPLVL=n Telemetry and Addr List Address List AT Commands Telemetry and Addr List Address List MVLEN=n IPL=n MVOFF=n MVMSK=hhMVOPT=n MVTYP=n MDn Commands in other groups associtated with Telemetry Destination Port and *DPORT Destination Address +CTA=n AT Commands CDMA/EV-DO$QCMIP=n ~NAMLCK=nnnnnn PROVISION=MSL,MDN/MIN,SID,NID EVDODIVERSITY=n Nam=0 Snmp Overview Raven X Snmp ConfigurationManagement Information Base MIB Snmp Traps Simple Network Management Protocol Snmp User Name and PasswordListening Port Security Level Trap Destination Snmp MIB Definition for AirLinkCommunity String Imports Simple Network Management Protocol Snmp Simple Network Management Protocol Snmp 100 101 102 Configuring your Raven X for PPPoE PPPoE PPP over Ethernet ConfigurationPPPoE Point to Point Protocol over Ethernet 103 104 PPPoE Point to Point Protocol over Ethernet 105 Configuring a PPPoE Connection in Windows Show All Connections 106 107 PPPoE 108 Select Finish to exit the Network Connection Wizard 109 Connect 110 111 Connecting to the Internet with PPPoE 112 Configuring your router for PPPoE with the Raven Windows Dial-up Networking DUN Installing the Modem Driver in Microsoft Windows113 114 Windows Dial-up Networking DUN Modem Driver 115 116 Dial-Up Networking PPP Configuration for Microsoft Windows 117 118 Phone Number 119 120 121 Modem Configuration Making a DUN Connection Establishing a DUN Connection using AceView122 Establishing a DUN Connection with Windows Networking Windows 98 and Windows NT123 124 Warranty Terms Warranty Terms and Conditions125 Warranty Terms and Conditions Warranty ConditionsRemedy 126 127 General Conditions FAQ Topics Frequently Asked Questions and Technical Support128 What is RSSI? Why is the Rssi for my Raven X negative? Frequently Asked Questions and Technical SupportWhat is the Proper RF Coverage for my Raven X? What Type of Antenna is Best for my Raven X? Can I use a portable battery to power my Raven X ? What do I need to power my Raven X ?130 Raven X’s IP Addresses and Local Networking What is the difference between Private and Public mode?131 Software Required 132 Does EV-DO provide any security? Security for the Raven133 134 Wireless Ace Reset Password 135 Activation Registering on the Verizon Network 136 Using Aleos How can I update the PRL Prefered Roaming List? What is a PRL?Prefered Roaming List PRL 137 138 Terminal Connection AT Commands AirLink Technical Support AirLink Technical SupportAirLink Support Web Site AirLink Documentation and Guides Contacting Technical Support