Dynamic IPs, Wireless Ace UDP Power-up Mode | Airlink X EV-DO

Modbus/BSAP Configuration

FIGURE 8. Wireless Ace: UDP Power-up Mode

2 - Enable

20

3. Configure IP addresses for the host.

If the Host modem has a static IP address, enter it in the Destination Address for S53. In Wireless Ace, select Misc in the side menu.

Setting the Host modem IP address as the S53 Destination Address provides a low level security. The modem will not forward UDP traffic unless the source IP/port matches what is in S53.

However, if you set *AIP=1, the modem will forward UDP traffic from any source IP address as long as it is accessing the modem on the configured *DPORT.

FIGURE 9. Wireless Ace: Destination IP

Dynamic IPs

If you do not have static IPs, the remote modems need to be configured to report their current IPs to a Dynamic DNS (DDNS) server with IP Manager (page 11). You will need to match the name of the modem to the names specified in the host modem’s MLIST or MLISTX for the connected RTU.

Instead of an IP, for S53, specify the name of the host modem (*MODEMNAME). If the remote modems are using a different DDNS than the host modem, you will need to specify the fully quali- fied domain name (*MODEMNAME+*DOMAIN).

With a name instead of IPs for the host modem, the remote modems will query the DNS server for the current IP assigned to the host modem before sending data back to the host.

4. Configure other RTU settings.

Raven X EV-DO for Verizon - User Guide, version 2.34

35

Image 41

Airlink X EV-DO manual Dynamic IPs, Wireless Ace UDP Power-up Mode

Contents

Version 2.34 April Raven X EV-DO Raven X EV-DO for Verizon User Guide, version Contents Contents Modbus/BSAP Configuration Simple Network Management Protocol Snmp Frequently Asked Questions and Technical Support EV-DO Overview Introduction to Raven X EV-DO Steps of a connection Establishing an Internet ConnectionIntroduction to Raven X EV-DO Dynamic vs. Static IP Addresses Using Your Raven X to Connect to the Internet Common Uses for the Raven Backup connection to the Internet Automatic Activation Quick Start Guide and Setup WizardActivating the Raven Activating the Raven Activating the Raven X using AT Commands AceView Utilities for the Raven Utilities for the Raven Wireless Ace AceNet AceNet Modem Doctor Modem Doctor Reasons to contact the modem and/or the connected device IP Manager and DNS IP Manager and DNS Fully Qualified Domain Name Dynamic Names Wireless Ace Dynamic IP Eairlink.com Data Usage for IP Manager Server UpdatesRestrictions for Modem Name Configuring DNS DNS Using Names Instead of IP addresses PPP-Peer Data Communication and Host Modes Data Communication and Host Modes AT Mode Wireless Ace PassThru PassThru Mode TelnetMode Wireless Ace Telnet Configuration Wireless Ace PPP/Ethernet PPP Mode UDP Auto Answer Slip ModeUDP Pad Reliable UDP UDP Multicast Mode Hybrid Modes TCP PAD Internal Dhcp Server Public and Private Mode AirLink Modem as a Gateway Dhcp in the Raven X using Public ModeDhcp and Routing PPPoE with Dhcp Keepalive Configuring Keepalive Data usage using Keepalive Modbus Overview Modbus/BSAP ConfigurationTelemetry Remote Terminal Unit RTU Supervisory Control and Data Acquisition Scada Modbus/BSAP ConfigurationProgrammable Logic Controller PLC Modbus TCP/IP Configuring the Raven X at the Polling Host for Modbus on Configuring the Raven Wireless Ace Device Port Dynamic IP Wireless Ace Addr List Configuring the Remote Modems for Modbus with UDP Dynamic IPs Wireless Ace UDP Power-up Mode Raven mounted in an enclosure with an RTU Power Connections Connecting the Antennas Hardware Installation Connecting the Raven X to a computer or other device Connecting PowerRaven X Indicator Lights Hardware Installation Light Patterns Monitoring Power-In Voltage and Internal Temperature Wireless Ace *POWERIN and *BOARDTEMP Built in Mounting Tabs for Raven Modem Placement Modem Placement Installing a Raven with an RTU Raven mounted in an enclosure with RTU Data Services & RF Features Specifications for the Raven X EV-DOPhysical Characteristics Power Management Specifications for the Raven X EV-DOPower consumption Environmental Using Wireless Ace AT Commands Wireless Ace Save / Load a Template AT Commands StartAll ProgramsAccessoriesCommunicationsHyperTerminal Using Telnet Terminal Emulation Direct Serial Connection HyperTerminal Comport Setting HyperTerminal Comport Settings Using AT Commands with a Terminal Application Symbols AT Command Listing Information and Status AT Commands Information and Status Autoprl ETHMAC? Prlstatus Bad Password Count OPRG=n AT Commands Misc MiscellaneousMisc Miscellaneous HOSTPAP=n DPORT=nNETALLOWZEROIP=n NETPW=pw STATUSCHK=n PRLDIAL=nSTATICIP=d.d.d.d +++ AT Commands SerialSerial Dmethodd.d.d.d/ppppp or Dmethod@name/ppppp S23=speed,databitsparitystop bits PPPNOCARRIER=n Set DTR mode S0=n AT Commands TCPS7=n S60=n TCPS=n S221=nTCPT=n ENQ=n AIP=n AT Commands UDPHOR=n MDhh S83=n S82=nDU=n UALL=n UDPLAST=n DNSUPDATE=n AT Commands DNSDNSn DNSUSER=d.d.d.d IPMANAGERn=name AT Commands Dynamic IPDOMAIN=name MODEMNAME=name IPMGRUPDATEn=mIPMGRKEYn=key PPP/Ethernet AT Commands PPP/Ethernet HOSTUID=string HOSTPRIVMODE=nHOSTPW=string PassThru AT Commands PassThru \APASSTHRU Smtp including SMS AT Commands Smtp including SMS NETSMS2EMAIL=n SMTPSEND=emailbody Other AT Commands OtherDAE=n DATZ=n MSCIUPDADDR=name/port IPPING=nMSCIUPDPERIOD=n NETWDOG=n SNMPSECLVL=n TELNETTIMEOUT=nSNMPTRAPDEST=host/port SNTP=n FM=n AT Commands FriendsFriends 255 = allow any number Logging AT Commands Logging DBGPPPLVL=n Telemetry and Addr List Address List AT Commands Telemetry and Addr List Address List MVLEN=n IPL=n MVOFF=n MVMSK=hhMVOPT=n MVTYP=n MDn Commands in other groups associtated with Telemetry Destination Port and *DPORT Destination Address +CTA=n AT Commands CDMA/EV-DO$QCMIP=n ~NAMLCK=nnnnnn PROVISION=MSL,MDN/MIN,SID,NID EVDODIVERSITY=n Nam=0 Snmp Overview Raven X Snmp ConfigurationManagement Information Base MIB Snmp Traps Simple Network Management Protocol Snmp User Name and PasswordListening Port Security Level Community String Snmp MIB Definition for AirLinkTrap Destination Imports Simple Network Management Protocol Snmp Simple Network Management Protocol Snmp 100 101 102 Configuring your Raven X for PPPoE PPPoE PPP over Ethernet ConfigurationPPPoE Point to Point Protocol over Ethernet 103 104 PPPoE Point to Point Protocol over Ethernet 105 Configuring a PPPoE Connection in Windows Show All Connections 106 107 PPPoE 108 Select Finish to exit the Network Connection Wizard 109 Connect 110 111 Connecting to the Internet with PPPoE 112 Configuring your router for PPPoE with the Raven 113 Installing the Modem Driver in Microsoft WindowsWindows Dial-up Networking DUN 114 Windows Dial-up Networking DUN Modem Driver 115 116 Dial-Up Networking PPP Configuration for Microsoft Windows 117 118 Phone Number 119 120 121 Modem Configuration 122 Establishing a DUN Connection using AceViewMaking a DUN Connection 123 Windows 98 and Windows NTEstablishing a DUN Connection with Windows Networking 124 125 Warranty Terms and ConditionsWarranty Terms Warranty Terms and Conditions Warranty ConditionsRemedy 126 127 General Conditions 128 Frequently Asked Questions and Technical SupportFAQ Topics What is RSSI? Why is the Rssi for my Raven X negative? Frequently Asked Questions and Technical SupportWhat is the Proper RF Coverage for my Raven X? What Type of Antenna is Best for my Raven X? 130 What do I need to power my Raven X ?Can I use a portable battery to power my Raven X ? 131 What is the difference between Private and Public mode?Raven X’s IP Addresses and Local Networking Software Required 132 133 Security for the RavenDoes EV-DO provide any security? 134 Wireless Ace Reset Password 135 Activation Registering on the Verizon Network 136 Using Aleos How can I update the PRL Prefered Roaming List? What is a PRL?Prefered Roaming List PRL 137 138 Terminal Connection AT Commands AirLink Technical Support AirLink Technical SupportAirLink Support Web Site AirLink Documentation and Guides Contacting Technical Support