Manuals / AMCC / Computer Equipment / Computer Hardware

AMCC 9590SE-4ME manual CLI Syntax Reference

Models: 9590SE-4ME

1 93

Download 93 pages 38.98 Kb

Page 74

Chapter 2. CLI Syntax Reference

//localhost> /c0/u0 migrate type=raid10 disk=2-3 stripe=16 Sending migration message to /c0/u0 ... Done.

3ware CLI> /c0 show

Unit UnitType Status %Cmpl Stripe Size(GB) Cache AVerify IgnECC

---------------------------------------------------------------------------

u0	Migrator MIGRATING		67%	-	74.4951	ON	OFF	OFF
Port	Status	Unit	Size		Blocks		Serial
---------------------------------------------------------------
p0	OK	u0	74.53 GB		156301488		3JV2Q1VA
p1	OK	u0	232.83 GB		488281250		WD-WMAEH15764
p2	OK	u0	232.83 GB		488281250		WD-WMAEH17004
p3	OK	u0	232.83 GB		488281250		WD-WMAEH17000
p4	NOT-PRESENT	-	-		-		-
p5	NOT-PRESENT	-	-		-		-
p6	NOT-PRESENT	-	-		-		-
p7	NOT-PRESENT	-	-		-		-
p8	NOT-PRESENT	-	-		-		-
p9	NOT-PRESENT	-	-		-		-
p10	NOT-PRESENT	-	-		-		-
p11	NOT-PRESENT	-	-		-		-
3ware CLI> /c0/u0 show
Unit	UnitType	Status		%Cmpl	Port Stripe		Size(GB)	Blocks

-----------------------------------------------------------------------

u0	Migrator	MIGRATING	67%	-	-	-	-
su0	RAID-1	OK	-	-	-	74.4951	156227584
su0-0	DISK	OK	-	p0	-	74.4951	156227584
su0-1	DISK	OK	-	p1	-	74.4951	156227584
du0	RAID-10	OK	-	-	16K	148.99	312455168
du0-0	RAID-1	OK	-	-	-	-	-
du0-0-0 DISK		OK	-	p0	-	74.4951	156227584
du0-0-1 DISK		OK	-	p1	-	74.4951	156227584
du0-1	RAID-1	OK	-	-	-	-	-
du0-1-0 DISK		OK	-	p2	-	74.4951	156227584
du0-1-1	DISK	OK	-	p3	-	74.4951	156227584

68	3ware Serial ATA RAID Controller CLI Guide for the Power Mac G5

Image 74

AMCC 9590SE-4ME manual CLI Syntax Reference, 3ware Serial ATA RAID Controller CLI Guide for the Power Mac G5

Contents

CLI Guide for the Power Mac G5 Command Line InterfaceSupports the 9590SE-4ME for the Power Mac G5 3wareDisclaimer CopyrightTrademarks Table of Contents Chapter 1. Introduction to the 3ware Command Line InterfaceChapter 2. CLI Syntax Reference Using the command interface interactively3ware Serial ATA RAID Controller CLI Guide for the Power Mac G5 cx/ux set autoverify=onoff cx/ux remove noscan quietcx/ux del noscan quiet cx/ux set identify=onoff3ware Serial ATA RAID Controller CLI Guide for the Power Mac G5 Return CodeAbout this CLI Guide Table 1 Sections in this CLI Guide3ware Serial ATA RAID Controller CLI Guide for the Power Mac G5 Introduction to the 3ware Command Line Interface Features of the CLISupported Operating Systems TerminologyWorking with 3ware CLI Installing the 3ware CLI on Mac OSTo install 3ware CLI on Mac OS Permissions Required to Run CLISyntax Using the command interface interactivelyUsing a single command with output ExampleScripting example Using an input file to execute a scriptOutputting the CLI to a Text File ExamplesUnderstanding RAID Levels and Concepts ConventionsRAID Concepts Available RAID Configurations RAIDRAID Figure 1. RAID 0 Configuration ExampleFigure 2. RAID 1 Configuration Example RAIDRAID Figure 3. RAID 5 Configuration ExampleFigure 4. RAID 10 Configuration Example Hot Spare Determining What RAID Level to UseSingle Disk Using Drive Capacity Efficiently Table 3 Drive CapacityCommon Tasks Mapped to CLI Commands CLI Syntax ReferenceCLI Command Table 4 Common Tasks Mapped to CLI Commands3ware Serial ATA RAID Controller CLI Guide for the Power Mac G5 Controller Configuration TasksCLI Command Common Tasks Mapped to CLI CommandsTable 4 Common Tasks Mapped to CLI Commands Unit Maintenance TasksSyntax Overview Syntax Shell Object Commandsfocus Object show show ver show rebuild show alarms reverseshow diag show verify show selftestrescan update fw=filenamewithpath forceflush commitSyntax Controller Object CommandsController Object Commands cx add rebuild=dddhhdurationcx show cx show attribute attribute cx show model cx show bioscx show driver cx show firmwarecx show pchip cx show serialcx show pcb cx show achipcx show ctlbus cx show numportscx show numunits cx show exportjbodcx show ondegrade cx show spinupcx show stagger cx show autocarvelocalhost /c0 show memory /c0 Memory Installed = 112MB cx show carvesizecx show memory localhost /c0 show autocarve /c0 Auto-Carving Policy = oncx show autorebuild cx show unitstatus3ware Serial ATA RAID Controller CLI Guide for the Power Mac G5 cx show allunitstatuscx show drivestatus Chapter 2. CLI Syntax ReferenceController Object Commands cx show allExample where x represents the actual version number Table 5 Supported Stripe Sizes group=3456 indicates the number of disks per group for a RAID 50 type. This attribute can only be used when type=raid50. Recall that a RAID 50 is cx rescan noscan Table 6 Supported Model-Unit Types for ignoreECCcx flush cx update fw=filenamewithpath forcecx commit Recommendation No need to update Given the above recommendation cx show alarms reversecx show diag The new image will take effect after rebootcx show rebuild If the rebuild schedule is enabled while a rebuild process is underway, the rebuild will pause until a scheduled time slot cx show verify Controller Object Commandscx show selftest 3ware Serial ATA RAID Controller CLI Guide for the Power Mac G5cx add rebuild=dddhhduration Setting Up a Rebuild ScheduleTo set up the rebuild schedule you want to use, follow this process cx add verify=dddhhduration Setting Up a Verify ScheduleTo set up the verify schedule you want to use, follow this process cx add selftest=dddhh Setting Up a Selftest ScheduleTo set up the selftest schedule you want to use, follow this process cx del rebuild=slotidcx del selftest=slotid cx set rebuild=enabledisable1..5cx del verify=slotid cx set exportjbod=onoff cx set verify=enabledisable1..5cx set selftest=enabledisable task=UDMASMART cx set stagger=nn cx set ondegrade=cacheofffollowcx set spinup=nn cx set autocarve=onoffSetting Auto-Carving Policy on /c0 to on ... Done cx set carvesize=1024..2048cx set autorebuild=onoff Setting Auto-Carving Size on /c0 to 2000 GB ... Donecx start mediascan cx stop mediascanSyntax Unit Object Commandscx/ux show cx/ux show attribute attribute cx/ux show statuscx/ux show initializestatus cx/ux show rebuildstatuscx/ux show verifystatus cx/ux show namecx/ux show identify cx/ux show qpolicycx/ux show storsave cx/ux show autoverifycx/ux show ignoreECC cx/ux show volumescx/ux show cache cx/ux show allExample of interactive mode //localhost /c0/u0 export cx/ux remove noscan quietcx/ux del noscan quiet Are you sure you want to delete the unit /c0/u0? Enter Y to continue cx/ux start rebuild disk=pp-p... ignoreECCcx/ux start verify cx/ux stop verify cx/ux pause rebuildcx/ux resume rebuild Table 7 Supported RAID Logical Unit Types for Verificationcx/ux set cache=onoff quiet cx/ux flushcx/ux set autoverify=onoff Table 8 Supported RAID Types for Cachingcx/ux set name=string cx/ux set identify=onoffcx/ux set ignoreECC=onoff cx/ux set qpolicy=onofflocalhost /c0/u5 set qpolicy = on cx/ux set storsave=protectbalanceperform quietSetting Command Queuing Policy for unit /c0/u5 to on ... Done Setting Command Storsave Policy for unit /c0/u5 to protect Done localhost /c0/u5 set storsave=protectTable 9 Valid Migration Paths Table 10 Supported Stripe Sizes 3ware Serial ATA RAID Controller CLI Guide for the Power Mac G5Example of capacity expansion Migration ProcessExample of splitting a mirror Example of migrate output3ware Serial ATA RAID Controller CLI Guide for the Power Mac G5 Chapter 2. CLI Syntax Referencecx/px show attribute attribute Port Object Commandscx/px show Syntaxcx/px show serial cx/px show statuscx/px show model cx/px show firmwarecx/px show capacity cx/px show ncqcx/px show lspeed cx/px show smartChapter 2. CLI Syntax Reference cx/px show all3ware Serial ATA RAID Controller CLI Guide for the Power Mac G5 ExampleSetting Port Identify on /c0/p5 to on ... Done cx/px remove noscan quietcx/px set identify=onoff localhost /c0/p5 set identify=onSyntax BBU Object Commandscx/bbu show cx/bbu show attribute attribute cx/bbu show statuscx/bbu show volt cx/bbu show batinstcx/bbu show lasttest cx/bbu show tempcx/bbu show fw cx/bbu show bootloadercx/bbu show serial cx/bbu show pcbcx/bbu enable cx/bbu disable quietSyntax Enclosure Object Commandsex show ex show slots ex show attribute attributeex show controllers ex show all ex show fansex show temp ex/slotx showex/fanx show ex/slotx show identifyex/slotx set identify=onoff ex/tempx showHelp Commands Help with specific commandsHelp with attributes help flush helphelp show AMCC/3ware CLI version Commands Descriptionhelp commit help updatehelp rescan help focushelp /ex Return Codehelp /cx/bbu help /ex/slotx