APC AP9608, AP9208 2 Product Description

2 Product Description

2.1 The Call-UPS II Panel

The SmartSlot Call-UPS II panel contains the management port and the

status indicator. See the figure below.

Management Port

Status

AP9608 Call-UPS Remote Mgt Device

SmartSlotSmartSlot

The external Call-UPS II rear panel contains the management port, status

indicator, UPS monitoring port, and optional power jack. See the figure

below.

2.2 Management Port

The Call-UPS II management port is used for configuring Call-UPS II and

for remote management and paging by modem. For specifications, see

Sec. 6.1.

2.3 UPS Monitoring Port [External Version]

The UPS monitoring connector duplicates the signals from the UPS so

that the normal computer-to-UPS connection is maintained. This port is

for use with APC software and interface kits only.

Contents

Main Thank You ! Radio frequency interference Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . .1 2 Product Description . . . . . . . . . . . . . . . . . . .2 3 Installation and Setup . . . . . . . . . . . . . . . . .5 4 Operation . . . . . . . . . . . . . . . . . . . . . . . . .11 Page 1 Introduction 1.1 Overview 1.2 Hardware Requirements 2 Product Description 2.1 The Call-UPS II Panel 2.2 Management Port 2.3 UPS Monitoring Port [External Version] 2.4 UPS Cable [External Version] 2.5 Power Port [External Version] With Smart-UPS With Matrix-UPS Page 3 Installation and Setup 3.1 Handling 3.2 Receiving Inspection 3.3 Installation SmartSlot 3.4 Confirm Operation 3.5 Configure Call-UPS II Initial Logging On Customize Settings Connect to Modem Page 4 Operation 4-1 Logging On to Call-UPS II 4.2 UPS Status [and Diagnostics] With Smart-UPS and Matrix-UPS UPS STATUS (Smart-UPS and Matrix-UPS) Page 15 With Symmetra Power Array UPS STATUS AND DI A GNO ST ICS ( Sym me t ra Po we r Ar ray ) IM Statu s RIM Status Last Xfer Reason for the last UPS transfer to battery. Possible Last Self Test Results of the last Self Test. Possible results are listed Input Output Load Curren t UPS STATUS AND DI AGNOSTICS (Symmetra Power Array, Continued) Page Page Page 20 4.3 UPS Control For remote control of the connected UPS, go to the Main menu and type 2 and press Select from the menu items to perform the following: UPS CONTROL Com mand Description Turn UPS ON Restores power to the load. Turn UPS OFF UPS CONTROL (Continued) Com mand Description Graceful Turn OFF Start(Stop) Runtime Calibration Put UPS in (Return from) Bypass 4.4 UPS Characteristics With Smart-UPS and Matrix-UPS 23 UPS CHARACTERISTICS (Smart-UPS and Matrix UPS) UPS CHARACTERISTICS (Smart-UPS and Matrix UPS, Cont.) With Symmetra Power Array UPS CHARACTERISTICS (Symmetra Power Array) 4.5 Data/Event Logging DATA/EVENT LOGGI N G Item Default Description 4.6 Call-UPS Settings CALL-UPS II SETTINGS CALL-UPS II SETTINGS ( Con t inu ed ) Answer Ring Reset Answer Lockou t UPS Presen t 4.7 Paging Setup PAGING SETUP Paging Repeat 1 Dial String 1 Dail String 2 PAGING SETUP (Continued) Site ID 12345678 Page Interva l Message Delay Space Characte r PAGING SETUP (E VENT S) Event Description 4.8 Measure-UPS Info 37 Press ENTER at the > prompt on the Measure-UPS screen to display fresh readings. MEASURE - UPS INF O 5 Problem Resolution 5.1 Troubleshooting Chart TROUBLESHOOTING Problem Possible Cause Solution 5.2 If Problems Persist MANAGEM E NT P ORT PINO UT Pin Function 6 Specifications 6.1 Management Port 6.2 Product Specifications Electric al Physical Envir onmental Approv als Appendix: Multiple SmartSlot Installation DEVICE PART # PRIORITY POSITION Triple Chassis Symmetra Power Array Daisy Chains Smart-UPS and Matrix-UPS Page Page Page Limited Warranty Life support policy