Manuals / ATEN Technology / Computer Equipment / Switch

ATEN Technology KM0832 user manual Setting the IP Address

Models: KM0832

1 137

Download 137 pages 50.15 Kb

Page 46

Setting the IP Address

KM0832 User Manual

Setting the IP Address

You can use a Web browser, the IP Installer, or the OSD to configure the KM0832 for deployment on your local network. To use a Web browser to configure the KM0832 you will need a computer equipped with a Web browser, an Ethernet hub with at least 2 ports, and 2 Cat 5 patch cables.

To configure the network settings via a Web browser:

1.Plug one end of a Cat 5 patch cable into the Ethernet hub and the other end into the CONFIGURATION port on the rear panel of the KM0832.

2.Plug one end of a Cat 5 patch cable into the Ethernet hub and the other end into the Ethernet adapter of a computer equipped with a Web browser.

3.Make sure that your computer’s IP address lies within the same subnet as that of the KM0832. (The default IP address for the KM0832 is 192.168.0.10.) Set the IP address for your computer’s network adapter to 192.168.0.XXX, where XXX represents any value from 1–254 (except 10 and 254, which are reserved for the KM0832). (See Factory Default Settings, page 108, for a list of the KM0832’s default network settings.)

Note: If you are using a proxy server, you might need to modify your computer’s proxy server settings before accessing the KM0832.

4.Enter 192.168.0.10 in your Web browser’s address bar. The KM0832 Login Webpage appears.

5.After logging in, assign a new IP address to the KM0832 that is appropriate for your local network. (See Network Configuration, page 38).

6.After logging out, reset your computer's network adapter settings back to their original values.

To configure the network settings via the IP Installer:

Go to the Altusen homepage and select the Webpage that is specific for the KM0832. From there you can download the IP Installer along with instructions on how to use it to assign an IP address to the KM0832.

To configure the network settings from within the OSD:

1.From the console, open the OSD. Navigate to the IP ADDRESS SET- TING screen (see SET NETWORK, page 94).

2.Follow the instructions in this user manual to manually set the IP address or to view the current settings. (If DHCP is enabled, you will not be able to view the IP address.)

30

Image 46

ATEN Technology KM0832 user manual Setting the IP Address

Contents

Page FCC Information KM0832 User ManualUser Notice Safety Instructions GeneralŠ Unplug the power cable before removing the power supply Rack Mounting Package Contents Introduction ContentsInstallation ChapterAdministrator Utility ChapterKeyboard Emulation OSD OperationHotkey Operation AppendixAdditional Installation Diagrams IndexSpecifications Factory Default Settings Restoring Original Factory Default Settings Troubleshooting GeneralAbout This Manual OverviewConventions This manual uses the following conventionsTechnical Support ALTUSEN InformationGetting Help Š In the United States of America, call 866-ALTUSEN Product InformationŠ In Canada and South America, call Š In all other locations, call This Page Intentionally Left Blank KM0832 User ManualChapter IntroductionOverview Features Benefits Consoles System RequirementsComputers Cables Operating Systems2. KVM Port LEDs 1. POWER LEDKM0832 Front View 3. User Port LEDs5. USER PORT 1 Switch 4. SYSTEM RESET Button6. USER PORT 1 Maintenance Port 3. CONFIGURATION Port 1. Power Socket2. POWER Switch 4. F/W UPGRADE Switch6. USER PORT 7. KVM PortsThis Page Intentionally Left Blank KM0832 User ManualOverview InstallationChapter KA9222 KA9272 KA9233Stacking and Rack Mounting Before you BeginStacking Rack Mounting-Split Chapter 2. InstallationKM0832 User Manual Rack Mounting-Front Phillips head hex M3 xRack Mounting-Rear Single Stage Installation page 109, for details Single Stage Installation DiagramConsole Module CPU ModuleMultilevel Installations OverviewCascading Protocol Interface Cascading1. Connect the console to the console module Console Module Protocol Interface Cascade DiagramKM0832 User Manual page 109, for detailsDaisy Chaining Chapter 2. Installation4. Power up the installation according to the following procedure page 109, for details KM0832 Console Module KM0432 Daisy Chain Installation DiagramChapter 2. Installation Console Module Next KM0432Network Installation Topology ConsiderationsBasic Operations Powering Off and RestartingSwitching Station Positions Hot PluggingThis Page Intentionally Left Blank KM0832 User ManualChapter Administrator UtilityOverview Setting the IP Address Logging In KM0832 Administrator Utility Menu Item MenusDescription Description IconsIcon Clicking the Log icon opens the Event Log Webpage, which allowsPort Status Port Settings , pageNaming Stations Setting the Webpage Session Timeout Network Configuration Port Settings IP AddressSystem Event Reports Setting the Date and Time 3. Under System Date & Time, select one of the following three options to set the date and time Group Management Adding GroupsModifying Groups Deleting Groups User Management Adding Users Permissions see Cascaded Installations, pageAdministrator UserNote Each user account can have only one group membership Modifying User Accounts Deleting User Accounts Port Management Accessing Ports Managing Port AccessTo open the Port Management Webpage for a port In the middle of the Webpage are six sets of arrows. Each set contains two arrows one facing leftward and the other facing rightward , which correspond to the boxes immediately to the left and right, respectively. Arrows are used to move users and groups from the boxes on the left into the boxes on the right and vice versa To grant port access rights to users or groups Cascaded Installations Description Configuring Port SettingsField Š If nothing is connected, the port note can be changed howeverSetting the OSD View See Managing Port Access on page View ModeSet Port ID PERSONAL VIEW on pageSelects which computers will be accessed under Auto Scan Mode Display DurationSet Scan Accessible-only those ports that the user is permitted to accessConfiguring OSD User Settings When set to ON, the beeper sounds whenever the port is switched SettingEnter the old account password. Enter a new password, and then when activating the Auto Scan function see page 97, or when anSearch Firmware Upgrade Before You BeginPerforming the Upgrade 6. Select or deselect Check Firmware VersionUpgrade Failed Firmware Upgrade RecoveryBackup and Restore Settings 4. Click Save. The File Download dialog box appears Viewing and Ending User Sessions To end a user session Viewing and Clearing the Log File 4. Click OK. The System Log Webpage appears Viewing System Information Viewing Help Logging OutThis Page Intentionally Left Blank KM0832 User ManualOSD Overview OSD OperationChapter After you log in, a screen similar to the one below appears OSD Main Screen Headings OSD NavigationCascaded Protocol Interface Installations Port ID NumberingOSD Functions F1 HELP To return to the OSD main screen, click or press Esccontinues on next page F2 VIEWSetting FunctionSCAN MODE-Selects which computers will be accessed under continued from previous pageSetting Functioncontinues on next page F3 SETSetting Functionwhen activating the Auto Scan function see F7 SCAN, p. 97, or SettingWhen activated, the beeper sounds whenever a port is changed continued from previous pageACCOUNT MANAGEMENT F4 ADMcontinues on next page continues on next page To change a users account passwordcontinued from previous page To change a users User Typecontinued from previous page SettingFunction To grant port access to a group PORT MANAGEMENTSetting To set the Group Access TypeTo set the User Access Type SettingTo grant port access to a user To revoke user access for a portcontinues on next page Settingcontinued from previous page FunctionSetting STATION MANAGEMENTSYSTEM INFORMATION fields. See Factory Default Settings, pageTo enable dynamic IP addressing with a DHCP server SADM CONFIGURATIONSetting To manually configure the IP settingscontinued from previous page SettingŠ While Broadcast Mode is in effect, a speaker symbol appears FunctionF5 SCH F7 SCAN F8 LOUT Invoking Hotkey Mode Hotkey OperationHotkey Port Control ChapterSelecting the Active Port Setting the Scan Interval Auto ScanningInvoking Auto Scan Hotkey Beeper Control Hotkey Summary TableThis Page Intentionally Left Blank KM0832 User ManualMac Keyboard Keyboard EmulationChapter PC Keyboard Sun KeyboardSun Keyboard Function SpecificationsAppendix KM0832Setting Factory Default SettingsThe factory default settings are as follows DefaultKA9233 PS/2-USB Console Module KA9272 USB Console Module Additional Installation DiagramsKA9222 PS/2 Console Module CONSOLEK LIN EKA9120 MODUL.NO CPUMODEL PS/2 KM0832 to KVM Adapter Cable ConnectionKA9120 PS/2 KVM Adapter Cable KA9130 Sun Legacy KVM Adapter Cable ATEN y bUPGRADE KA9131 Sun USB KVM Adapter Cable KA9140 Serial KVM Adapter CableKA9170 USB KVM Adapter Cable UPGRADERestoring Original Factory Default Settings 6. Remove the jumper cap from pins 1-2 of the J3 jumper Solution TroubleshootingProblem GeneralSolution Sun SystemsProblem AppendixLimited Warranty Index Page Page