3 TROUBLESHOOTING
Troubleshooting
In the following cases, the machine is not broken. Be sure to check the following before asking for the machine to be serviced.
|
| Problem | Item to check | Countermeasure |
| |
Display does not appear. | Is the power supply connected? | Connect the AC adaptor correctly. | ||||
|
|
|
| (see page 13) | ||
|
|
|
|
| ||
|
|
| Is the power switch on? | Turn the power on. (see page 13) | ||
|
|
|
|
| ||
|
|
| Isn't the cable of the AC Adapter dam- | Replace the AC Adapter if its interior | ||
|
|
| aged? | circuit or the cable is damaged. | ||
|
|
|
| Use only CAT EYE AC Adapter. | ||
|
|
|
|
|
| |
ERROR or irregular display appears | Isn't the data card reversed? | Hold the card yellow arrow side up, | ||||
when you insert the data card. |
| and insert to the direction of arrow. | ||||
|
|
|
|
| ||
|
|
| Didn't you insert the card too quickly? | Insert the card slowly. | ||
|
|
|
|
| ||
|
|
| Didn't you specify two or more pro- | Refer to P.42~43 and specify the pro- | ||
|
|
| grams, or open unnecessary holes? | gram and conditions correctly. | ||
|
|
|
|
|
| |
When the pulse (earlobe) sensor is | Is the earlobe sensor attached correctly | Attach the sensor correctly to your ear- | ||||
used, the pulse rate displayed on the | to your earlobe? | lobe and take care not to swing the sen- | ||||
control unit remains at “0”. |
| sor or sensor cable during the exercise. | ||||
Is the sensor plug completely inserted | ||||||
The pulse rate increases abnormally. | If the sensor cable proves to be dam- | |||||
into the sensor jack? | ||||||
|
|
| aged, replace the whole pulse sensor | |||
|
|
|
| |||
|
|
| Isn't the sensor cable damaged? | |||
|
|
| with a new one. | |||
|
|
|
| |||
When the | Is the earlobe sensor plug connected to | When the earlobe sensor is connected, | ||||
pulse rate displayed on the control unit | the control unit? | signals from the | ||||
remains at “0”. |
| not received. Remove the earlobe sen- | ||||
|
|
|
| sor plug from the control unit. | ||
|
|
|
|
| ||
|
|
| Is the chest belt attached correctly? | Attach the chest belt correctly accord- | ||
|
|
|
| ing to the procedure. | ||
|
|
|
|
| ||
|
|
| Is the chest belt loose? | Attach the chest belt with the electrode | ||
|
|
|
| area making contact with your body. | ||
|
|
|
|
| ||
|
|
| Is the air dry? (especially in winter) | Slightly dampen the electrode area of | ||
|
|
|
| the chest belt. | ||
|
|
|
|
| ||
|
|
| Has the electrode belt deteriorated or | Replace it with a new electrode belt. | ||
|
|
| has it become worn or damaged due to |
|
| |
|
|
|
|
| ||
|
|
|
|
| ||
|
|
| Is the battery low? | Replace it with a new battery. | ||
|
|
|
|
| ||
When the | Is the chest belt attached correctly? | Attach the chest belt correctly accord- | ||||
pulse rate displayed on the control unit |
| ing to the procedure. | ||||
indicates “0” or measurement starts. |
|
|
| |||
Does the pulse rate indicate “0” at a | The battery is low. Replace it with a | |||||
|
|
| ||||
|
|
| distance from the control unit and does | new battery. If the problem persists, | ||
|
|
| measurement start when closer to the | check the receiving board in the con- | ||
|
|
| unit? | trol unit. | ||
|
|
|
| |||
The evaluation of fitness level seems | Is the weight unit correct? | Set the weight unit correctly. (see page | ||||
incorrect. |
| 48) |
| |||
|
|
| ||||
The exercise program indicates “STOP | Does a buzzer sound because your pulse | Set your age properly so that the alarm | ||||
EXERCISE” and ends prematurely. | rate exceeds the upper pulse limit speci- | does not sound. | ||||
|
|
| fied in the program? |
|
| |
|
|
|
| |||
Clattering noise is heard with the | Are the pedals firmly attached to the | Attach the pedals firmly. | ||||
pedal rotation. | crank? If not, noise may be produced. |
|
| |||
|
|
|
|
|
| |
49 
