Corporate Headquarters | Cisco Systems 78-13983-04 instruction

Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide

Corporate Headquarters

Cisco Systems, Inc.

170 West Tasman Drive San Jose, CA 95134-1706

USA http://www.cisco.com Tel: 408 526-4000

800553-NETS (6387)

Fax: 408 526-4100

Customer Order Number: DOC-7813983=

Text Part Number: 78-13983-04

Image 1

Cisco Systems 78-13983-04 manual Corporate Headquarters, Customer Order Number DOC-7813983= Text Part Number

Contents

Customer Order Number DOC-7813983= Text Part Number Corporate Headquarters Copyright 2002 Cisco Systems, Inc All rights reserved Limitations and Restrictions First-Time Configuration Software FeaturesAbout This Guide Audience Saving Configuration Changes Using the Setup Command FacilityConfiguring PIM Configuring PPP Multiplexing Where to Go Next Configuring RedundancyMode y-cable Assigning a QoS Boilerplate to an InterfacePage Audience ObjectivesOrganization Chapter Title Description Convention Description Document ConventionsBoldface font Boldface screen Related Documentation Additional InformationObtaining Documentation World Wide Web Documentation CD-ROM Obtaining Technical AssistanceOrdering Documentation Documentation Feedback Cisco.com To access Cisco.com, go to the following websiteTechnical Assistance Center Contacting TAC by Telephone Benefits Overview of the MWR Cisco IOS Software Software FeaturesNetwork Processor Software MLP, PPP Control Path IPCP, NCP, LCP, Clns RTP/UDP Header Compression PPP Multiplexing/Demultiplexing RTP Header Compression Redundancy Support MWR 1900 supports the following MIBs MIB SupportRFC1213-MIB RFC1253-MIB 802.1Q VLANs Frame Relay FR Limitations and Restrictions Before You Begin Understanding Boot ImagesUnderstanding Interface Numbering Interface type Slot number/Interface number Configuring Global Parameters Using the Setup Command FacilityBefore Starting Your Router Enter a host name for the router this example uses Viewing the configuration You are then prompted to configure the specified interface Completing the ConfigurationSummary of interfaces is displayed First-Time Configuration Where to Go Next Where to Go Next Getting Help Cisco IOS Software Basics Configure terminal Understanding Command ModesExit , or logout As interface serial 0/0 Saving Configuration Changes Undoing a Command or FeaturePage Configuring with the Command-Line Interface Enter global configuration mode Configuring the Host Name and PasswordPrompt changes to Routerconfig# Verifying the Version of Cisco IOS Software Exit to global configuration mode Configuring Loopback InterfacesExit interface configuration mode Change the name of the router to a meaningful name Configuring the FE Interface IP Address Configuring Fast Ethernet InterfacesSetting the Speed and Duplex Mode Configuring PIM Configuring Routing Protocol AttributesSpecify the speed Configuring Hsrp Support Enabling the FE Interface Configuring Multilink InterfacesSpecify a priority Configuring IP Address Assignment Configuring Multilink PPPEnable multilink PPP operation Configuring RTP/UDP Compression Configuring PPP MultiplexingTo set the default PPP protocol ID, enter To set the maximum length of the subframe, enter RPM-3config-if#ip rtp header-compression Configuring T1 Interfaces Configuring T1 and E1 Interfaces Set the carrier delay for the serial interface Configuring E1 Interfaces Configuring QoS Attributes Creating a Policy Map Creating a Class Map 78-13983-04 Assigning a QoS Boilerplate to an Interface Configuring RedundancyRedundant MWR 1900s Stand-Alone MWR Exit y-mode configuration modeSpecify the interface to be used for backhauling MWR1900-1#show running-config Verifying the Configuration Match access-group Ip ospf message-digest-key 1 md5 mymd5pw Ip ospf Hello-interval Ospf Dead-interval Monitoring and Managing the MWR Command Purpose Show Commands for Monitoring the MWR Show interface type slot / port Show controllersShow protocols Command Reference Clear ip rtp header-compression Related Commands Description Command Modes Command History Usage Guidelines ExamplesClear ppp mux Clear ppp mux interface interface Connections Interface configuration Syntax Description Defaults Command ModesIp rtp header-compressionEnables RTP header compression Ip rtp compression-connections Ip rtp header-compression Syntax Description Defaults Command Modes Command HistoryPassive Related Commands Description Mode y-cable Mode y-cableStandalone Standby use-interface Ppp mux Command Modes Command History Ppp mux delay integer no ppp mux delay Ppp mux delayUsage Guidelines Examples Related Commands Default maximum length is Interface configuration Defaults Command Modes Command HistoryPpp mux frame Ppp mux frame integer no ppp mux frame Ppp mux pid integer Ppp mux pid Ppp mux subframe length integer No ppp mux subframe length Ppp mux subframe length Ppp mux subframe count Default maximum is Interface configurationPpp mux subframe count integer No ppp mux subframe count Following example enables redundancy mode Global configurationInvoked y-cable mode Redundancy Show ip rtp header-compression type number detail Show ip rtp header-compression1describes the significant fields shown in the display Field Description That can exist on an interface Interface interface Show ppp mux 2describes the significant fields shown in the display Ppp mux Enables PPP multiplexing/demultiplexing Show redundancy This command has no attributes Invokes redundancy mode Invokes y-cable modeStand-alone configuration Standby Cable configuration Syntax Description DefaultsStandalone No standalone Standby use-interface interface health revertive backhaul Standby use-interface Standby use-interface loopback102 revertive Page IP address Cisco IOS About Command modes Enable modeCounters, PPP multiplexing IN-2 MIB support Mode y-cable Configuring Command IN-4