Cisco Systems 78-13983-04 manual

Chapter 5 Command Reference

standby use-interface

Examples		The following example specifies loopback101 as the health interface and loopback102 as the revertive
		interface.
		standby use-interface loopback101 health
		standby use-interface loopback102 revertive
		standby use-interface multilink1 backhaul

Related Commands		Command	Description

		mode y-cable	Invokes y-cable mode.

		redundancy	Invokes redundancy mode.

		standalone	Specifies whether the MWR 1900 router is used in a redundant or
			stand-alone configuration.

		standby	Sets HSRP attributes

Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide

	78-13983-04	5-23

Image 75

Cisco Systems 78-13983-04 manual Standby use-interface loopback102 revertive

Contents

Customer Order Number DOC-7813983= Text Part Number Corporate Headquarters Copyright 2002 Cisco Systems, Inc All rights reserved Audience Software FeaturesLimitations and Restrictions First-Time Configuration About This Guide Configuring PPP Multiplexing Using the Setup Command FacilitySaving Configuration Changes Configuring PIM Assigning a QoS Boilerplate to an Interface Configuring RedundancyWhere to Go Next Mode y-cablePage Chapter Title Description ObjectivesAudience Organization Boldface screen Document ConventionsConvention Description Boldface font World Wide Web Additional InformationRelated Documentation Obtaining Documentation Documentation Feedback Obtaining Technical AssistanceDocumentation CD-ROM Ordering Documentation To access Cisco.com, go to the following website Cisco.comTechnical Assistance Center Contacting TAC by Telephone Benefits Overview of the MWR MLP, PPP Control Path IPCP, NCP, LCP, Clns Software FeaturesCisco IOS Software Network Processor Software RTP/UDP Header Compression PPP Multiplexing/Demultiplexing RTP Header Compression Redundancy Support RFC1253-MIB MIB SupportMWR 1900 supports the following MIBs RFC1213-MIB 802.1Q VLANs Frame Relay FR Limitations and Restrictions Understanding Boot Images Before You BeginUnderstanding Interface Numbering Interface type Slot number/Interface number Using the Setup Command Facility Configuring Global ParametersBefore Starting Your Router Enter a host name for the router this example uses Viewing the configuration Completing the Configuration You are then prompted to configure the specified interfaceSummary of interfaces is displayed First-Time Configuration Where to Go Next Where to Go Next Getting Help Cisco IOS Software Basics As interface serial 0/0 Understanding Command ModesConfigure terminal Exit , or logout Saving Configuration Changes Undoing a Command or FeaturePage Configuring with the Command-Line Interface Verifying the Version of Cisco IOS Software Configuring the Host Name and PasswordEnter global configuration mode Prompt changes to Routerconfig# Change the name of the router to a meaningful name Configuring Loopback InterfacesExit to global configuration mode Exit interface configuration mode Configuring Fast Ethernet Interfaces Configuring the FE Interface IP AddressSetting the Speed and Duplex Mode Configuring Routing Protocol Attributes Configuring PIMSpecify the speed Configuring Hsrp Support Configuring Multilink Interfaces Enabling the FE InterfaceSpecify a priority Configuring Multilink PPP Configuring IP Address AssignmentEnable multilink PPP operation To set the maximum length of the subframe, enter Configuring PPP MultiplexingConfiguring RTP/UDP Compression To set the default PPP protocol ID, enter RPM-3config-if#ip rtp header-compression Configuring T1 Interfaces Configuring T1 and E1 Interfaces Set the carrier delay for the serial interface Configuring E1 Interfaces Configuring QoS Attributes Creating a Policy Map Creating a Class Map 78-13983-04 Configuring Redundancy Assigning a QoS Boilerplate to an InterfaceRedundant MWR 1900s Exit y-mode configuration mode Stand-Alone MWRSpecify the interface to be used for backhauling MWR1900-1#show running-config Verifying the Configuration Match access-group Ip ospf message-digest-key 1 md5 mymd5pw Ip ospf Hello-interval Ospf Dead-interval Monitoring and Managing the MWR Command Purpose Show Commands for Monitoring the MWR Show controllers Show interface type slot / portShow protocols Command Reference Clear ip rtp header-compression Clear ppp mux interface interface Command Modes Command History Usage Guidelines ExamplesRelated Commands Description Clear ppp mux Ip rtp compression-connections Syntax Description Defaults Command ModesConnections Interface configuration Ip rtp header-compressionEnables RTP header compression Syntax Description Defaults Command Modes Command History Ip rtp header-compressionPassive Related Commands Description Standby use-interface Mode y-cableMode y-cable Standalone Ppp mux Command Modes Command History Ppp mux delay Ppp mux delay integer no ppp mux delayUsage Guidelines Examples Related Commands Ppp mux frame integer no ppp mux frame Defaults Command Modes Command HistoryDefault maximum length is Interface configuration Ppp mux frame Ppp mux pid integer Ppp mux pid Ppp mux subframe length integer No ppp mux subframe length Ppp mux subframe length Default maximum is Interface configuration Ppp mux subframe countPpp mux subframe count integer No ppp mux subframe count Redundancy Global configurationFollowing example enables redundancy mode Invoked y-cable mode Field Description Show ip rtp header-compressionShow ip rtp header-compression type number detail 1describes the significant fields shown in the display That can exist on an interface Interface interface Show ppp mux 2describes the significant fields shown in the display Ppp mux Enables PPP multiplexing/demultiplexing Show redundancy This command has no attributes Standby Invokes y-cable modeInvokes redundancy mode Stand-alone configuration No standalone Syntax Description DefaultsCable configuration Standalone Standby use-interface interface health revertive backhaul Standby use-interface Standby use-interface loopback102 revertive Page Cisco IOS About Command modes Enable mode IP addressCounters, PPP multiplexing IN-2 MIB support Mode y-cable Configuring Command IN-4