Cisco Systems 78-13983-04 specs

Chapter 4 Configuring with the Command-Line Interface

Verifying the Configuration

!

!Setup SNMP

snmp community private rw snmp community public ro

snmp-server enable traps snmp-server trap-source Loopback 0

snmp-server host cw4mw public

!Setup useful aliases

!

ip host omcr OMCR_ip_address ip host omcip OMCIP_ip_address ip host cw4mw CW4MW_ip_address

ip host btsha-other-0 192.168.146.2 ip host btsha-other-1 192.168.147.2

!

!interface Multilink1 description Backhaul Interface ip unnumbered loopback 2

cdp enable ppp multilink

ip ospf hello-interval 1 ip ospf dead-interval 3

ip ospf message-digest-key 1 md5 mymd5pw

!

interface Multilink2 description

ip unnumbered loopback 2 ip mroute-cache

ip mtu 256 cdp enable ppp multilink

ip rtp header-compression

ip rtp compression-connections 700 ppp mux

pppmux subframe length 64 ppp mux subrame count 15 ppp mux frame 256

ppp mux delay 800 ppp mux pid 0x2067

ip ospf hello-interval 1 ip ospf dead-interval 3

ip ospf message-digest-key 1 md5 mymd5pw ip pim sparse-mode

ip pim version 2 service-policy output llq-policy

!

interface FastEthernet0/0

ip address 192.168.146.1 255.255.255.0 no ip proxy-arp

no ip mroute-cache

keepalive 1 full-duplex

speed 100

ntp broadcast version 3

standby 1 ip 192.168.146.3
standby 1		timers 1	3
standby 1		priority	100
standby	1	preempt
standby	1	name one

			standby 1	track FastEthernet0/1 10
			standby 1	track	Loopback101	10
			standby 1	track	Loopback102	5
			Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide

	4-20					78-13983-04
	4-20					78-13983-04

Image 48

Cisco Systems 78-13983-04 manual Ip ospf message-digest-key 1 md5 mymd5pw

Contents

Corporate Headquarters Customer Order Number DOC-7813983= Text Part Number Copyright 2002 Cisco Systems, Inc All rights reserved Software Features Limitations and Restrictions First-Time ConfigurationAbout This Guide Audience Using the Setup Command Facility Saving Configuration ChangesConfiguring PIM Configuring PPP Multiplexing Configuring Redundancy Where to Go NextMode y-cable Assigning a QoS Boilerplate to an InterfacePage Objectives AudienceOrganization Chapter Title Description Document Conventions Convention DescriptionBoldface font Boldface screen Additional Information Related DocumentationObtaining Documentation World Wide Web Obtaining Technical Assistance Documentation CD-ROMOrdering Documentation Documentation Feedback To access Cisco.com, go to the following website Cisco.comTechnical Assistance Center Contacting TAC by Telephone Overview of the MWR Benefits Software Features Cisco IOS SoftwareNetwork Processor Software MLP, PPP Control Path IPCP, NCP, LCP, Clns PPP Multiplexing/Demultiplexing RTP/UDP Header Compression Redundancy Support RTP Header Compression MIB Support MWR 1900 supports the following MIBsRFC1213-MIB RFC1253-MIB Limitations and Restrictions 802.1Q VLANs Frame Relay FR Understanding Boot Images Before You BeginUnderstanding Interface Numbering Interface type Slot number/Interface number Using the Setup Command Facility Configuring Global ParametersBefore Starting Your Router Viewing the configuration Enter a host name for the router this example uses Completing the Configuration You are then prompted to configure the specified interfaceSummary of interfaces is displayed Where to Go Next First-Time Configuration Where to Go Next Cisco IOS Software Basics Getting Help Understanding Command Modes Configure terminalExit , or logout As interface serial 0/0 Undoing a Command or Feature Saving Configuration ChangesPage Configuring with the Command-Line Interface Configuring the Host Name and Password Enter global configuration modePrompt changes to Routerconfig# Verifying the Version of Cisco IOS Software Configuring Loopback Interfaces Exit to global configuration modeExit interface configuration mode Change the name of the router to a meaningful name Configuring Fast Ethernet Interfaces Configuring the FE Interface IP AddressSetting the Speed and Duplex Mode Configuring Routing Protocol Attributes Configuring PIMSpecify the speed Configuring Hsrp Support Configuring Multilink Interfaces Enabling the FE InterfaceSpecify a priority Configuring Multilink PPP Configuring IP Address AssignmentEnable multilink PPP operation Configuring PPP Multiplexing Configuring RTP/UDP CompressionTo set the default PPP protocol ID, enter To set the maximum length of the subframe, enter RPM-3config-if#ip rtp header-compression Configuring T1 and E1 Interfaces Configuring T1 Interfaces Configuring E1 Interfaces Set the carrier delay for the serial interface Configuring QoS Attributes Creating a Class Map Creating a Policy Map 78-13983-04 Configuring Redundancy Assigning a QoS Boilerplate to an InterfaceRedundant MWR 1900s Exit y-mode configuration mode Stand-Alone MWRSpecify the interface to be used for backhauling Verifying the Configuration MWR1900-1#show running-config Match access-group Ip ospf message-digest-key 1 md5 mymd5pw Ip ospf Hello-interval Ospf Dead-interval Monitoring and Managing the MWR Show Commands for Monitoring the MWR Command Purpose Show controllers Show interface type slot / portShow protocols Command Reference Clear ip rtp header-compression Command Modes Command History Usage Guidelines Examples Related Commands DescriptionClear ppp mux Clear ppp mux interface interface Syntax Description Defaults Command Modes Connections Interface configurationIp rtp header-compressionEnables RTP header compression Ip rtp compression-connections Syntax Description Defaults Command Modes Command History Ip rtp header-compressionPassive Related Commands Description Mode y-cable Mode y-cableStandalone Standby use-interface Command Modes Command History Ppp mux Ppp mux delay Ppp mux delay integer no ppp mux delayUsage Guidelines Examples Related Commands Defaults Command Modes Command History Default maximum length is Interface configurationPpp mux frame Ppp mux frame integer no ppp mux frame Ppp mux pid Ppp mux pid integer Ppp mux subframe length Ppp mux subframe length integer No ppp mux subframe length Default maximum is Interface configuration Ppp mux subframe countPpp mux subframe count integer No ppp mux subframe count Global configuration Following example enables redundancy modeInvoked y-cable mode Redundancy Show ip rtp header-compression Show ip rtp header-compression type number detail1describes the significant fields shown in the display Field Description That can exist on an interface Show ppp mux Interface interface Ppp mux Enables PPP multiplexing/demultiplexing 2describes the significant fields shown in the display This command has no attributes Show redundancy Invokes y-cable mode Invokes redundancy modeStand-alone configuration Standby Syntax Description Defaults Cable configurationStandalone No standalone Standby use-interface Standby use-interface interface health revertive backhaul Standby use-interface loopback102 revertive Page Cisco IOS About Command modes Enable mode IP addressCounters, PPP multiplexing MIB support Mode y-cable IN-2 Command Configuring IN-4