Related Commands Description | Cisco Systems 78-13983-04 specs

Chapter 5 Command Reference

ip rtp header-compression

Related Commands	Command	Description
	clear ip rtp	Clears RTP header compression structures and statistics.
	header-compression

	ip rtp	Specifies the total number of RTP header compression connections
	compression-connections	that can exist on an interface.

	show ip rtp	Displays RTP header compression statistics.
	header-compression

Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide

5-6	78-13983-04

Page 58

Image 58

Cisco Systems 78-13983-04 manual Related Commands Description

Contents

Corporate Headquarters Customer Order Number DOC-7813983= Text Part Number Copyright 2002 Cisco Systems, Inc All rights reserved About This Guide Software FeaturesLimitations and Restrictions First-Time Configuration Audience Configuring PIM Using the Setup Command FacilitySaving Configuration Changes Configuring PPP Multiplexing Mode y-cable Configuring RedundancyWhere to Go Next Assigning a QoS Boilerplate to an InterfacePage Organization ObjectivesAudience Chapter Title Description Boldface font Document ConventionsConvention Description Boldface screen Obtaining Documentation Additional InformationRelated Documentation World Wide Web Ordering Documentation Obtaining Technical AssistanceDocumentation CD-ROM Documentation Feedback Cisco.com To access Cisco.com, go to the following websiteTechnical Assistance Center Contacting TAC by Telephone Overview of the MWR Benefits Network Processor Software Software FeaturesCisco IOS Software MLP, PPP Control Path IPCP, NCP, LCP, Clns PPP Multiplexing/Demultiplexing RTP/UDP Header Compression Redundancy Support RTP Header Compression RFC1213-MIB MIB SupportMWR 1900 supports the following MIBs RFC1253-MIB Limitations and Restrictions 802.1Q VLANs Frame Relay FR Before You Begin Understanding Boot ImagesUnderstanding Interface Numbering Interface type Slot number/Interface number Configuring Global Parameters Using the Setup Command FacilityBefore Starting Your Router Viewing the configuration Enter a host name for the router this example uses You are then prompted to configure the specified interface Completing the ConfigurationSummary of interfaces is displayed Where to Go Next First-Time Configuration Where to Go Next Cisco IOS Software Basics Getting Help Exit , or logout Understanding Command ModesConfigure terminal As interface serial 0/0 Undoing a Command or Feature Saving Configuration ChangesPage Configuring with the Command-Line Interface Prompt changes to Routerconfig# Configuring the Host Name and PasswordEnter global configuration mode Verifying the Version of Cisco IOS Software Exit interface configuration mode Configuring Loopback InterfacesExit to global configuration mode Change the name of the router to a meaningful name Configuring the FE Interface IP Address Configuring Fast Ethernet InterfacesSetting the Speed and Duplex Mode Configuring PIM Configuring Routing Protocol AttributesSpecify the speed Configuring Hsrp Support Enabling the FE Interface Configuring Multilink InterfacesSpecify a priority Configuring IP Address Assignment Configuring Multilink PPPEnable multilink PPP operation To set the default PPP protocol ID, enter Configuring PPP MultiplexingConfiguring RTP/UDP Compression To set the maximum length of the subframe, enter RPM-3config-if#ip rtp header-compression Configuring T1 and E1 Interfaces Configuring T1 Interfaces Configuring E1 Interfaces Set the carrier delay for the serial interface Configuring QoS Attributes Creating a Class Map Creating a Policy Map 78-13983-04 Assigning a QoS Boilerplate to an Interface Configuring RedundancyRedundant MWR 1900s Stand-Alone MWR Exit y-mode configuration modeSpecify the interface to be used for backhauling Verifying the Configuration MWR1900-1#show running-config Match access-group Ip ospf message-digest-key 1 md5 mymd5pw Ip ospf Hello-interval Ospf Dead-interval Monitoring and Managing the MWR Show Commands for Monitoring the MWR Command Purpose Show interface type slot / port Show controllersShow protocols Command Reference Clear ip rtp header-compression Clear ppp mux Command Modes Command History Usage Guidelines ExamplesRelated Commands Description Clear ppp mux interface interface Ip rtp header-compressionEnables RTP header compression Syntax Description Defaults Command ModesConnections Interface configuration Ip rtp compression-connections Ip rtp header-compression Syntax Description Defaults Command Modes Command HistoryPassive Related Commands Description Standalone Mode y-cableMode y-cable Standby use-interface Command Modes Command History Ppp mux Ppp mux delay integer no ppp mux delay Ppp mux delayUsage Guidelines Examples Related Commands Ppp mux frame Defaults Command Modes Command HistoryDefault maximum length is Interface configuration Ppp mux frame integer no ppp mux frame Ppp mux pid Ppp mux pid integer Ppp mux subframe length Ppp mux subframe length integer No ppp mux subframe length Ppp mux subframe count Default maximum is Interface configurationPpp mux subframe count integer No ppp mux subframe count Invoked y-cable mode Global configurationFollowing example enables redundancy mode Redundancy 1describes the significant fields shown in the display Show ip rtp header-compressionShow ip rtp header-compression type number detail Field Description That can exist on an interface Show ppp mux Interface interface Ppp mux Enables PPP multiplexing/demultiplexing 2describes the significant fields shown in the display This command has no attributes Show redundancy Stand-alone configuration Invokes y-cable modeInvokes redundancy mode Standby Standalone Syntax Description DefaultsCable configuration No standalone Standby use-interface Standby use-interface interface health revertive backhaul Standby use-interface loopback102 revertive Page IP address Cisco IOS About Command modes Enable modeCounters, PPP multiplexing MIB support Mode y-cable IN-2 Command Configuring IN-4