Cisco Systems AS5350XM, AS5400XM Installing the CT3 Feature Card

4-5

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter4 Channelized T3 Feature Card

Online Insertion and Removal of the CT3 Feature Card

Figure4-6 Removing the Feature Card from the CiscoAS5350XM Universal Gateway

Figure4-7 Removing the Feature Card from the CiscoAS5400XM Universal Gateway

Step10 After you remove the feature card from the chassis, set it aside on an ESD-preventive mat.

Step11 If a feature card slot on the carrier card is to remain empty, install a blank cover over the open feature

card slot to ensure proper airflow inside the chassis. (See Figure 4-8.)

Figure4-8 Blank Feature Card Cover

Installing the CT3 Feature Card

Warning

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement1001

Note When you replace a feature card with a new feature card of the same type in the same slot, the system

software recognizes the new feature card and brings up the trunk interfaces automatically. If you replace

the existing feature card with a new feature card of a different type, you must reconfigure the system.

For configuration details, see the CiscoAS5350XM and Cisco AS5400XM Universal Gateways Software

Configuration Guide.

58761

37168

36033

Contents

Main Page CONTENTS Page Page Page Preface Document Organization Document Conventions ix x Page xii Page Obtaining Documentation Cisco.com Product Documentation DVD Ordering Documentation Documentation Feedback Cisco Product Security Overview Reporting Security Problems in Cisco Products Obtaining Technical Assistance Cisco Technical Support & Documentation Website Submitting a Service Request Definitions of Service Request Severity Obtaining Additional Publications and Information Page Page Safety Warnings, Recommendations, and Tools Required General Safety Maintaining Safety with Electricity Preventing Electrostatic Discharge Required Tools and Equipment Page Feature Card and Carrier Card Guidelines Online Insertion and Removal of Feature Cards Removing and Installing Populated Carrier Cards Removing a Populated Carrier Card 2-4 Figure2-2 Loosening the Captive Screws on the CiscoAS5350XM Figure2-4 Removing the Carrier Card from the CiscoAS5350XM Figure2-3 Loosening the Captive Screws on the CiscoAS5400XM to the carrier card. Installing a Populated Carrier Card Page Page Page T1 and E1 Feature Cards Online Installation and Removal of the T1 or E1 Feature Card Removing the T1 or E1 Feature Card Page 3-5 Figure3-6 Loosening the Captive Screws on the CiscoAS5350XM Universal Gateway Figure3-7 Loosening the Captive Screws on the CiscoAS5400XM Universal Gateway 3-6 Figure3-9 Removing the Feature Card from the CiscoAS5400XM Universal Gateway Online Insertion and Removal Example for the T1 or E1 Feature Card 3-7 3-8 Installing the T1 or E1 Feature Card 3-10 Figure3-12 Installing the T1 or E1 Feature Card in the Cisco AS5400XM Universal Gateway LEDs, see Chapter 7, Troubleshooting. Figure3-14 Tightening the Captive Screws on the Cisco AS5400XM Universal Gateway Configuring Input Impedance for the E1 Feature Card Configuration Verification Channelized T3 Feature Card Online Insertion and Removal of the CT3 Feature Card Removing the CT3 Feature Card Page Page Installing the CT3 Feature Card Page Page Page Universal Port and Dial-Only Feature Cards Restrictions for the Universal Port and Dial-Only Feature Cards Online Insertion and Removal of the Universal Port or Dial-Only Feature Card Removing the Universal Port or Dial-Only Feature Card Page 5-5 Figure5-4 Loosening the Captive Screws on the CiscoAS5350XM Universal Gateway Figure5-6 Removing the Feature Card from the CiscoAS5350XM Universal Gateway Figure5-5 Loosening the Captive Screws on the CiscoAS5400XM Universal Gateway 5-6 Online Insertion and Removal Example for the Universal Port or Dial-Only Feature Card 5-7 Installing the Universal Port or Dial-Only Feature Card 5-9 their holes. System Processing Engine Firmware Voice Feature Card Restrictions for the Voice Feature Card Online Insertion and Removal of the Voice Feature Card Removing the Voice Feature Card Page 6-5 Figure6-4 Loosening the Captive Screws on the CiscoAS5350XM Universal Gateway Figure6-6 Removing a Feature Card from the CiscoAS5350XM Universal Gateway Figure6-5 Loosening the Captive Screws on the CiscoAS5400XM Universal Gateway Online Insertion and Removal Example for the Voice Feature Card Installing the Voice Feature Card Replacing PVDM2 Modules in the Voice Feature Card Orienting the PVDM2 Module During Installation Removing PVDM2 Modules From the Voice Feature Card Installing PVDM2 Modules in the Voice Feature Card Digital Signal Processor Firmware View from front of board Page Troubleshooting LEDs 7-2 Page Page Mixing WAN Feature Cards Mixing Universal Port and Dial-Only Feature Cards Mixing Voice Feature Cards With Universal Port and Dial-Only Feature Cards Monitoring the Chassis Environment 7-8 3. When the operating temperature of the system rises above 149F (65C), Cisco IOS software shuts down all feature cards immediately. Displaying Environment Status The output shown below displays on your console during normal operating conditions. The slot The output shown below displays on your console when the system reaches a warning state: The output shown below displays on your console when the system reaches a critical state: 7-9 The output shown below displays on your console when the system reaches a shutdown state: Using the Bantam Jack Ports to Monitor T1, E1, and CT3 Feature Cards Using Drop and Insert Mode on the CT3 Feature Card Troubleshooting Network Interfaces Page APPENDIX A Cabling Specifications 2-Port and 4-Port T1 or E1 Feature Card Cable and Port Pinouts Page Page Page Page 8-Port T1 or E1 Feature Card Cable and Port Pinouts Page Page Page Page Page CT3 Feature Card Cable and Port Pinouts Bantam Jack Port Pinouts Page INDEX Numerics A B G I L M R S T U V