Cisco Systems AS5350XM, AS5400XM - page 77

7-3

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter7 Troubleshooting

LEDs

Tab l e 7-1 LE D s

Feature Card LED State Description

T1 or E1

feature card

ACTIVITY (ACT) Fast flicker (green) The feature card is up and running.

Slow flicker (green) The feature card is not yet fully functional.

OK/MAINT Green The feature card has passed initial power-up diagnostics

tests and is operating normally.

Yellow •The feature card is busied out, but there are active

calls. Once all the calls are terminated the feature

card will be powered off.

•The feature card is not functioning correctly.

Off All calls associated with the card have been shut down,

and it is safe to remove the card with the system powered

on.

•Remote Alarm (RA)

•Local Alarm (LA)

•Loopback (LB)

On (yellow) One LED below each T1/E1 port indicates one of the

following:

•A local or remote loopback diagnostic test is running

on the associated T1 port.

•An alarm has been received on the associated T1/E1

port, indicating loss of signal (LOS) or loss of

multiframe alignment (LOF) at the local or remote

node.

Contents

Main Page CONTENTS Page Page Page Preface Document Organization Document Conventions ix x Page xii Page Obtaining Documentation Cisco.com Product Documentation DVD Ordering Documentation Documentation Feedback Cisco Product Security Overview Reporting Security Problems in Cisco Products Obtaining Technical Assistance Cisco Technical Support & Documentation Website Submitting a Service Request Definitions of Service Request Severity Obtaining Additional Publications and Information Page Page Safety Warnings, Recommendations, and Tools Required General Safety Maintaining Safety with Electricity Preventing Electrostatic Discharge Required Tools and Equipment Page Feature Card and Carrier Card Guidelines Online Insertion and Removal of Feature Cards Removing and Installing Populated Carrier Cards Removing a Populated Carrier Card 2-4 Figure2-2 Loosening the Captive Screws on the CiscoAS5350XM Figure2-4 Removing the Carrier Card from the CiscoAS5350XM Figure2-3 Loosening the Captive Screws on the CiscoAS5400XM to the carrier card. Installing a Populated Carrier Card Page Page Page T1 and E1 Feature Cards Online Installation and Removal of the T1 or E1 Feature Card Removing the T1 or E1 Feature Card Page 3-5 Figure3-6 Loosening the Captive Screws on the CiscoAS5350XM Universal Gateway Figure3-7 Loosening the Captive Screws on the CiscoAS5400XM Universal Gateway 3-6 Figure3-9 Removing the Feature Card from the CiscoAS5400XM Universal Gateway Online Insertion and Removal Example for the T1 or E1 Feature Card 3-7 3-8 Installing the T1 or E1 Feature Card 3-10 Figure3-12 Installing the T1 or E1 Feature Card in the Cisco AS5400XM Universal Gateway LEDs, see Chapter 7, Troubleshooting. Figure3-14 Tightening the Captive Screws on the Cisco AS5400XM Universal Gateway Configuring Input Impedance for the E1 Feature Card Configuration Verification Channelized T3 Feature Card Online Insertion and Removal of the CT3 Feature Card Removing the CT3 Feature Card Page Page Installing the CT3 Feature Card Page Page Page Universal Port and Dial-Only Feature Cards Restrictions for the Universal Port and Dial-Only Feature Cards Online Insertion and Removal of the Universal Port or Dial-Only Feature Card Removing the Universal Port or Dial-Only Feature Card Page 5-5 Figure5-4 Loosening the Captive Screws on the CiscoAS5350XM Universal Gateway Figure5-6 Removing the Feature Card from the CiscoAS5350XM Universal Gateway Figure5-5 Loosening the Captive Screws on the CiscoAS5400XM Universal Gateway 5-6 Online Insertion and Removal Example for the Universal Port or Dial-Only Feature Card 5-7 Installing the Universal Port or Dial-Only Feature Card 5-9 their holes. System Processing Engine Firmware Voice Feature Card Restrictions for the Voice Feature Card Online Insertion and Removal of the Voice Feature Card Removing the Voice Feature Card Page 6-5 Figure6-4 Loosening the Captive Screws on the CiscoAS5350XM Universal Gateway Figure6-6 Removing a Feature Card from the CiscoAS5350XM Universal Gateway Figure6-5 Loosening the Captive Screws on the CiscoAS5400XM Universal Gateway Online Insertion and Removal Example for the Voice Feature Card Installing the Voice Feature Card Replacing PVDM2 Modules in the Voice Feature Card Orienting the PVDM2 Module During Installation Removing PVDM2 Modules From the Voice Feature Card Installing PVDM2 Modules in the Voice Feature Card Digital Signal Processor Firmware View from front of board Page Troubleshooting LEDs 7-2 Page Page Mixing WAN Feature Cards Mixing Universal Port and Dial-Only Feature Cards Mixing Voice Feature Cards With Universal Port and Dial-Only Feature Cards Monitoring the Chassis Environment 7-8 3. When the operating temperature of the system rises above 149F (65C), Cisco IOS software shuts down all feature cards immediately. Displaying Environment Status The output shown below displays on your console during normal operating conditions. The slot The output shown below displays on your console when the system reaches a warning state: The output shown below displays on your console when the system reaches a critical state: 7-9 The output shown below displays on your console when the system reaches a shutdown state: Using the Bantam Jack Ports to Monitor T1, E1, and CT3 Feature Cards Using Drop and Insert Mode on the CT3 Feature Card Troubleshooting Network Interfaces Page APPENDIX A Cabling Specifications 2-Port and 4-Port T1 or E1 Feature Card Cable and Port Pinouts Page Page Page Page 8-Port T1 or E1 Feature Card Cable and Port Pinouts Page Page Page Page Page CT3 Feature Card Cable and Port Pinouts Bantam Jack Port Pinouts Page INDEX Numerics A B G I L M R S T U V