Manuals / Brands / Computer Equipment / Network Card / Cisco Systems / Computer Equipment / Network Card

Cisco Systems AS5350XM, AS5400XM Replacing PVDM2 Modules in the Voice Feature Card

1 104

Download 104 pages, 11.68 Mb

6-8

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter6 Voice Feature Card

Replacing PVDM2 Modules in the Voice Feature Card

Figure6-11 Tightening the Captive Screws on the CiscoAS5350XM Universal Gateway

Figure6-12 Tightening the Captive Screws on the CiscoAS5400XM Universal Gateway

Step6 Check the OK/MAINT LED to verify that the card is working properly. For information about the voice

feature card LED, see the “LEDs” section on page 7-1.

Note To use the voice feature card, at least one voice feature card must be present when the universal

gateway is powered on. More voice feature cards can be inserted later. See the “Restrictions for

the Voice Feature Card” section on page6-2 for more information.

Replacing PVDM2 Modules in the Voice Feature Card

The voice feature card contains six 80-pin SIMM sockets for PVDM2 modules, numbered 0 through 5.

(See Figure 6-13.) Each socket can be filled with a single 80-pin PVDM2 module.

Note The voice feature card supports a 64-channel PVDM2 (AS5X-PVDM2-64) module.

36818

Carrier card

DFC

Chassis

Captive

screw

Captive

screw

37202

Captive

screw Captive

screw

Contents

Main Page CONTENTS Page Page Page Preface Document Organization Document Conventions ix x Page xii Page Obtaining Documentation Cisco.com Product Documentation DVD Ordering Documentation Documentation Feedback Cisco Product Security Overview Reporting Security Problems in Cisco Products Obtaining Technical Assistance Cisco Technical Support & Documentation Website Submitting a Service Request Definitions of Service Request Severity Obtaining Additional Publications and Information Page Page Safety Warnings, Recommendations, and Tools Required General Safety Maintaining Safety with Electricity Preventing Electrostatic Discharge Required Tools and Equipment Page Feature Card and Carrier Card Guidelines Online Insertion and Removal of Feature Cards Removing and Installing Populated Carrier Cards Removing a Populated Carrier Card 2-4 Figure2-2 Loosening the Captive Screws on the CiscoAS5350XM Figure2-4 Removing the Carrier Card from the CiscoAS5350XM Figure2-3 Loosening the Captive Screws on the CiscoAS5400XM to the carrier card. Installing a Populated Carrier Card Page Page Page T1 and E1 Feature Cards Online Installation and Removal of the T1 or E1 Feature Card Removing the T1 or E1 Feature Card Page 3-5 Figure3-6 Loosening the Captive Screws on the CiscoAS5350XM Universal Gateway Figure3-7 Loosening the Captive Screws on the CiscoAS5400XM Universal Gateway 3-6 Figure3-9 Removing the Feature Card from the CiscoAS5400XM Universal Gateway Online Insertion and Removal Example for the T1 or E1 Feature Card 3-7 3-8 Installing the T1 or E1 Feature Card 3-10 Figure3-12 Installing the T1 or E1 Feature Card in the Cisco AS5400XM Universal Gateway LEDs, see Chapter 7, Troubleshooting. Figure3-14 Tightening the Captive Screws on the Cisco AS5400XM Universal Gateway Configuring Input Impedance for the E1 Feature Card Configuration Verification Channelized T3 Feature Card Online Insertion and Removal of the CT3 Feature Card Removing the CT3 Feature Card Page Page Installing the CT3 Feature Card Page Page Page Universal Port and Dial-Only Feature Cards Restrictions for the Universal Port and Dial-Only Feature Cards Online Insertion and Removal of the Universal Port or Dial-Only Feature Card Removing the Universal Port or Dial-Only Feature Card Page 5-5 Figure5-4 Loosening the Captive Screws on the CiscoAS5350XM Universal Gateway Figure5-6 Removing the Feature Card from the CiscoAS5350XM Universal Gateway Figure5-5 Loosening the Captive Screws on the CiscoAS5400XM Universal Gateway 5-6 Online Insertion and Removal Example for the Universal Port or Dial-Only Feature Card 5-7 Installing the Universal Port or Dial-Only Feature Card 5-9 their holes. System Processing Engine Firmware Voice Feature Card Restrictions for the Voice Feature Card Online Insertion and Removal of the Voice Feature Card Removing the Voice Feature Card Page 6-5 Figure6-4 Loosening the Captive Screws on the CiscoAS5350XM Universal Gateway Figure6-6 Removing a Feature Card from the CiscoAS5350XM Universal Gateway Figure6-5 Loosening the Captive Screws on the CiscoAS5400XM Universal Gateway Online Insertion and Removal Example for the Voice Feature Card Installing the Voice Feature Card Replacing PVDM2 Modules in the Voice Feature Card Orienting the PVDM2 Module During Installation Removing PVDM2 Modules From the Voice Feature Card Installing PVDM2 Modules in the Voice Feature Card Digital Signal Processor Firmware View from front of board Page Troubleshooting LEDs 7-2 Page Page Mixing WAN Feature Cards Mixing Universal Port and Dial-Only Feature Cards Mixing Voice Feature Cards With Universal Port and Dial-Only Feature Cards Monitoring the Chassis Environment 7-8 3. When the operating temperature of the system rises above 149F (65C), Cisco IOS software shuts down all feature cards immediately. Displaying Environment Status The output shown below displays on your console during normal operating conditions. The slot The output shown below displays on your console when the system reaches a warning state: The output shown below displays on your console when the system reaches a critical state: 7-9 The output shown below displays on your console when the system reaches a shutdown state: Using the Bantam Jack Ports to Monitor T1, E1, and CT3 Feature Cards Using Drop and Insert Mode on the CT3 Feature Card Troubleshooting Network Interfaces Page APPENDIX A Cabling Specifications 2-Port and 4-Port T1 or E1 Feature Card Cable and Port Pinouts Page Page Page Page 8-Port T1 or E1 Feature Card Cable and Port Pinouts Page Page Page Page Page CT3 Feature Card Cable and Port Pinouts Bantam Jack Port Pinouts Page INDEX Numerics A B G I L M R S T U V