OL-11187-01 | Cisco Systems SFS 3012R guide

Chapter 2 Installing and Booting the Cisco SFS 3012R Server Switch

Safety

Warning This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security. Statement 1017

Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030

Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040

Warning This equipment must be installed and maintained by service personnel as defined by AS/NZS 3260. Incorrectly connecting this equipment to a general-purpose outlet could be hazardous. The telecommunications lines must be disconnected 1) before unplugging the main power connector or 2) while the housing is open, or both. Statement 1043

Warning This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation. Install only in accordance with national and local wiring regulations. Statement 1045

Warning Use of controls, adjustments, or performing procedures other than those specified may result in hazardous radiation exposure. Statement 1057

Cisco SFS 3012R Multifabric Server Switch Hardware Installation Guide

2-2	OL-11187-01

Image 34

Cisco Systems SFS 3012R manual OL-11187-01

Contents

Corporate Headquarters Text Part Number OL-11187-01Page N T E N T S Blower Modules Cisco SFS 3012R Server Switch LEDs OL-11187-01 Organization AudienceChapter Title Description Conventions Convention Description Statement 1071-Warning Definition Bewaar Deze Instructies Avvertenza Importanti Istruzioni Sulla Sicurezza Warnung Wichtige SicherheitshinweiseAviso Instruções Importantes DE Segurança Guarde Estas Instrucciones GEM Disse Anvisninger Xiii Related Documentation Xiv Cisco.com Obtaining DocumentationProduct Documentation DVD Ordering Documentation Documentation Feedback Reporting Security Problems in Cisco ProductsCisco Product Security Overview Obtaining Technical Assistance Product Alerts and Field NoticesCisco Technical Support & Documentation Website Submitting a Service Request Definitions of Service Request Severity Obtaining Additional Publications and Information Xix Preface Obtaining Additional Publications and Information Cisco SFS 3012R Server Switch Overview Introduction Unified Fabric FeaturesPerformance Transparent Topology Scalability Fully Redundant System Architecture Cisco SFS 3012R Server Switch Chassis 6 8 10 12 Cisco SFS 3012R Server Switch Components Controller Modules Cisco SFS 3012R Server Switch Controller Module Ethernet and Fibre Channel Gateways Ethernet ports Ethernet gateway status LEDs Ejector handle Fibre Channel Gateway Expansion Module InfiniBand Switch Modules InfiniBand Switch Module Power Supply Modules Power Supply Module Blower Modules Blower Module OL-11187-01 Installing and Booting the Cisco SFS 3012R Server Switch Safety OL-11187-01 Preparing for Installation Installing Cisco SFS 3012R Server Switch Components Mounting the Cisco SFS 3012R Server Switch on a Rack Mounting bracket Shelf rail Attaching the Shelf to the Rack Positioning and Sliding the Chassis onto the Shelf Firmly tighten the shelf screws at the cable end Attaching a Serial Console Cable to a PC or Terminal Assigning a Static IP Address Obtaining an IP Address with Dhcp Connecting InfiniBand Hosts Following example InfiniBand Cable with Pinch Connector Managing the Cisco SFS 3012R Server Switch Removing a Pinch Connector A P T E R Installing a Controller Module Inserting the Controller Module Adding or Replacing Ethernet or Fibre Channel Gateways Installing an InfiniBand Switch Module Close both fastener levers simultaneously and completely Securing an InfiniBand Switch Module Removing an InfiniBand Switch Module Installing a Power Supply Module 180762 Removing a Power Supply Module Installing a Blower Module Inserting a Power Supply Removing a Blower Module OL-11187-01 Viewing and Updating the Software Image Viewing the Software Image Version Viewing the Software Image Version with the CLI SFS-3012R#show card-inventory Viewing the Software Image Version of the Controller Module Updating the Software Image Viewing Current Image of an Individual Module Updating the Software Image with the CLI This example shows the copy operation Updating the Software Image with the Element Manager GUI Click the Import button Import File window appears Select Maintenance-Reboot Deleting a Software Image Deleting an Image with the CLI Select Maintenance File Management Deleting an Image with the Element Manager GUI Cisco SFS 3012R Server Switch LEDs Cisco SFS 3012R Server Switch System Status LED LED State Indication Power Supply LEDs Power Supply LEDs Blower Module LEDs Blower Module LEDs Controller LED States Indication Controller LEDsBlower LED States Indication Power LED States Indication Location of Management Ethernet Port LEDs InfiniBand LEDs InfiniBand Switch Module LEDsLED States Indication InfiniBand Port LEDs Fibre Channel LEDs Fibre Channel Gateway LEDs Fibre Channel Port LEDs Off Gbps Solid green Ethernet Gateway LEDs Location of Ethernet Gateway and Ethernet Port LEDs Ethernet Gateway LEDs Ethernet Port LEDs General Specifications Specification Detail Laser Specifications Electrical SpecificationsCertifications/Regulatory D E IN-2 IN-3 IN-4