Fan Belt Adjustment | Cub Cadet 7532, 7530 specs

MAINTENANCE/ADJUSTMENTS

Fan Belt Adjustment

Fan Belt Tension Check Interval

Daily or after 10 Hours

NOTE: Adjust the belt tension after the first 50 hours of operation and replace when necessary.

Measure the fan belt for correct tension. Check to see if the belt deflection is about 13mm (0.5 inch) when pushing the belt with 10 kg (22 lb) load at point 1 .

ADJUSTING

BOLT

PIVOT NUT

Rotating fan and belts. Contact can injure. Keep clear.

To Adjust the fan belt tension loosen the adjusting bolt and pivot nut of the alternator. Move the alternator away from the engine until correct belt tension is reached. Tighten the adjusting bolt and pivot nut to a torque of 16 Nm (12 lb ft).

NOTE: Too much tension will cause alternator and water pump bearing failure and belt wear. Too little tension will cause a decrease in alternator output and belt wear.

105

Image 113

Cub Cadet 7532, 7530 manual Fan Belt Adjustment, Rotating fan and belts. Contact can injure. Keep clear

Contents

Series Manufacturer Statement Owner ’s warranty responsibility Length of Coverage Maintenance Right Turn Right Turn Left Rear Serial Numbers General Table of Contents Basic Safety Requirements For Maintenance Safety PrecautionsGeneral Operating Safety Precaution Cover the PTO shaft with a guard when not using SAFETY/DECALS SAFETY/DECALS SAFETY/DECALS Steering and Turning the Tractor SAFETY/DECALS AT T E R I E S C O N TA I N a C I D a N D E X P L O S I V E Decals Rotating Machine Parts Tractor Roll Over Foldable Rops Frame Roll Over Protective Structure Rops Low Clearance Positions Step General Diesel EngineEngine Lubrication System Fuel System Air Intake System Power TrainCooling System Tractor Brakes Mechanical Front Drive MFD ClutchDifferential Lock Steering Mid Power Takeoff PTO Option Rear Power Takeoff PTOHydraulic System Drawbar 7532 1365 mm Inch Height To top of Rops 7530 2110 mm Tachometer and Hourmeter Instruments and Indicators Fuel Gauge Engine Coolant Temperature GaugeTurn Signal Indicators Independent PTO Clutch Indicatorgear Drive only Engine Glow Plug IndicatorEngine OIL Pressure Indicator Operating Controls Control Switches Flasher Control Button Engine Speed Control Lever Turn Signal Switch Accelerator Pedal Gear Drive only Control Levers and Pedals Gear Drive Hydrostatic Drive Brake Pedal Lock Brake Pedals Hydrostatic Drive Park Brake Lever Clutch Lock Latch Clutch Pedal Control Levers Gear Drive Hydrostatic Drive INSTRUMENTS/CONTROLS MID PTO Control Lever if Equipped PTO Switch Hitch Control Lever Gear Drive Hydrostatic Drive Gear Drive Hydrostatic Drive Differential Lock Pedal Hydraulic Flow Control Knob MFD Control Lever Steering Column Tilt Operators Seat Before Starting the Engine RUN in Procedure Normal Starting Procedure Step Push the clutch pedal down Operating Instruction Stopping the Engine Cold Temperature Operation Stopping the Engine Keep Engine AT Correct Operating TemperatureWarming the Engine and Transmission Towing HOW to Transport Tractor Transmission Operation Gear Drive Transmission Hydrostatic Drive Transmission Gear Drive Differential LockTo Engage the Differential Lock To Disengage the Differential Lock Engage the Rear PTO AS Follows Power Takeoff PTODisengage the Rear PTO AS Follows Disengage the MID PTO AS Follows Engage the MID PTO AS Follows Power Takeoff Guards Drawbar Connecting Implements PTO Operating SafetyThree Point Hitch Connecting Implements Without MID PTO DrawbarWith MID PTO Flasher Control Button Lamp Switch Turn Signal PTO RPM PTO Shaft Diameter Dimension a Connecting Implement to Drawbar Safety Chain Three Point Hitch System Lift Links Hitch System Adjustments Stabilizer Upper Link Hitch Operation Connecting Implement to HitchDisconnecting Implement from Hitch Hitch Control Lever Hitch Lowering Speed Adjustment Hydraulic Block Adding Fluid after Connecting Cylinders and Hoses Tire and RIM Equipment Tire Inflation Specifications Pressure PLY Tire Load CapacityPLY Check Air Pressure Tire Inflation Procedure Wheel Mounting Torques Bolts and Nuts Positions Torque Front Wheel Adjustment To Check the TOE-IN, USE the Following Procedure Toe-in AdjustmentFront Axle Type MFD RH Side Tractor Equipped with Adjustable Wheels Tire Size Style Supplier Tire Size COMBINATIONS-MFD Tractor Ballast Front End Weights TIRES/WHEELS/SPACING/BALLAST Hood Lubrication Table Engine Hour meter Service Hour Interval Service After First 50 Hours System System Capacities Frequency in Hours Page Page Engine Oil Level Service Specifications Engine Oil Change Engine Oil Filter Pressure Cooling System Cooling System Coolant Solutions Cleaning The Cooling System Water Removal from the Filter Cup Fuel System Specifications For Acceptable Number Two Diesel Fuel Diesel Fuel Specifications Fuel Filter Element Replacement Fuel System Air Removal Fuel Injection Pump and Nozzle Check Dump Valve AIR Induction System Air Filter Element Removal System Inspection Element Cleaning Transmission Oil Level Gear Drive Transmission & Hydraulic LubricationTransmission Oil Level Hydrostatic Drive Stou OIL Start the engine and check for leaks Transmission Oil Change Change the Hydraulic Filter AS Follows Hydraulic Filter Gear & Hydrostatic Drive Hydrostatic System Filter Hydrostatic Drive Front Axle Oil Level Front Axle Lubrication MFD Front Axle Oil Change Grille Screens and Radiator Area Rotating fan and belts. Contact can injure. Keep clear Fan Belt Adjustment Fan Belt Replacement Free Movement Adjustment Clutch Pedal Adjustment Brake Pedal Adjustment Raise Stop Setting Position Electrical System Specifications Alternator Charging System General Service Information Fuses Line Fuse Auxiliary Battery Connections Battery Removal and Installation of Battery Battery Cables and Terminals When Battery Is Not in Use When Charging the Battery Storing the Tractor Removing from Storage