RH Side | Cub Cadet 7532, 7530 guide

TIRES/WHEELS/SPACING/BALLAST

TO ADJUST THE TOE-IN, USE THE FOLLOWING PROCEDURE: Adjust the rods to be equal the dimensions A on both side.

1.Loosen the lock nut at the rod end.

2.Turn the rod to shorten or lengthen the tie rod.

3.Look the lock nuts.

Tightening torque

147 to 166 Nm (109 to123lbft)

LOCK NUT

BOLT

ROD

FILL HOLE

(RH SIDE)

LOCK NUT

BOLT

LOCK NUT

ROD END

ROD

		(RH SIDE)
	A	(RH SIDE)
	A

71

Image 79

Cub Cadet 7532, 7530 manual RH Side

Contents

Series Manufacturer Statement Owner ’s warranty responsibility Length of Coverage Maintenance Right Turn Right Turn Left Rear Serial Numbers General Table of Contents General Operating Safety Precaution Safety PrecautionsBasic Safety Requirements For Maintenance Cover the PTO shaft with a guard when not using SAFETY/DECALS SAFETY/DECALS SAFETY/DECALS Steering and Turning the Tractor SAFETY/DECALS AT T E R I E S C O N TA I N a C I D a N D E X P L O S I V E Decals Rotating Machine Parts Tractor Roll Over Foldable Rops Frame Roll Over Protective Structure Rops Low Clearance Positions Step Fuel System Diesel EngineGeneral Engine Lubrication System Tractor Brakes Power TrainAir Intake System Cooling System Steering ClutchMechanical Front Drive MFD Differential Lock Drawbar Rear Power Takeoff PTOMid Power Takeoff PTO Option Hydraulic System 7532 1365 mm Inch Height To top of Rops 7530 2110 mm Tachometer and Hourmeter Instruments and Indicators Turn Signal Indicators Engine Coolant Temperature GaugeFuel Gauge Engine OIL Pressure Indicator Engine Glow Plug IndicatorIndependent PTO Clutch Indicatorgear Drive only Operating Controls Control Switches Flasher Control Button Engine Speed Control Lever Turn Signal Switch Accelerator Pedal Gear Drive only Control Levers and Pedals Gear Drive Hydrostatic Drive Brake Pedal Lock Brake Pedals Hydrostatic Drive Park Brake Lever Clutch Lock Latch Clutch Pedal Control Levers Gear Drive Hydrostatic Drive INSTRUMENTS/CONTROLS MID PTO Control Lever if Equipped PTO Switch Hitch Control Lever Gear Drive Hydrostatic Drive Gear Drive Hydrostatic Drive Differential Lock Pedal Hydraulic Flow Control Knob MFD Control Lever Steering Column Tilt Operators Seat Before Starting the Engine RUN in Procedure Normal Starting Procedure Step Push the clutch pedal down Operating Instruction Stopping the Engine Cold Temperature Operation Warming the Engine and Transmission Keep Engine AT Correct Operating TemperatureStopping the Engine Towing HOW to Transport Tractor Transmission Operation Gear Drive Transmission Hydrostatic Drive Transmission To Disengage the Differential Lock Differential LockGear Drive To Engage the Differential Lock AS Follows Power Takeoff PTOEngage the Rear PTO AS Follows Disengage the Rear PTO Disengage the MID PTO AS Follows Engage the MID PTO AS Follows Power Takeoff Guards Three Point Hitch Connecting Implements PTO Operating SafetyDrawbar Connecting Implements With MID PTO DrawbarWithout MID PTO Flasher Control Button Lamp Switch Turn Signal PTO RPM PTO Shaft Diameter Dimension a Connecting Implement to Drawbar Safety Chain Three Point Hitch System Lift Links Hitch System Adjustments Stabilizer Upper Link Disconnecting Implement from Hitch Connecting Implement to HitchHitch Operation Hitch Control Lever Hitch Lowering Speed Adjustment Hydraulic Block Adding Fluid after Connecting Cylinders and Hoses Tire and RIM Equipment Tire Inflation Specifications PLY Tire Load CapacityPressure PLY Check Air Pressure Tire Inflation Procedure Wheel Mounting Torques Bolts and Nuts Positions Torque Front Wheel Adjustment MFD Toe-in AdjustmentTo Check the TOE-IN, USE the Following Procedure Front Axle Type RH Side Tractor Equipped with Adjustable Wheels Tire Size Style Supplier Tire Size COMBINATIONS-MFD Tractor Ballast Front End Weights TIRES/WHEELS/SPACING/BALLAST Hood Lubrication Table Engine Hour meter Service Hour Interval Service After First 50 Hours System System Capacities Frequency in Hours Page Page Engine Oil Level Service Specifications Engine Oil Change Engine Oil Filter Pressure Cooling System Cooling System Coolant Solutions Cleaning The Cooling System Water Removal from the Filter Cup Fuel System Specifications For Acceptable Number Two Diesel Fuel Diesel Fuel Specifications Fuel Filter Element Replacement Fuel System Air Removal Fuel Injection Pump and Nozzle Check Dump Valve AIR Induction System Air Filter Element Removal System Inspection Element Cleaning Stou OIL Transmission & Hydraulic LubricationTransmission Oil Level Gear Drive Transmission Oil Level Hydrostatic Drive Start the engine and check for leaks Transmission Oil Change Change the Hydraulic Filter AS Follows Hydraulic Filter Gear & Hydrostatic Drive Hydrostatic System Filter Hydrostatic Drive Front Axle Oil Level Front Axle Lubrication MFD Front Axle Oil Change Grille Screens and Radiator Area Rotating fan and belts. Contact can injure. Keep clear Fan Belt Adjustment Fan Belt Replacement Free Movement Adjustment Clutch Pedal Adjustment Brake Pedal Adjustment Raise Stop Setting Position Electrical System Specifications Alternator Charging System General Service Information Fuses Line Fuse Auxiliary Battery Connections Battery Removal and Installation of Battery Battery Cables and Terminals When Battery Is Not in Use When Charging the Battery Storing the Tractor Removing from Storage