Fan Belt Replacement | Cub Cadet 7530, 7532 guide

MAINTENANCE/ADJUSTMENTS

Fan Belt Replacement

To replace the fan belt, use following procedure:

STEP 1

BONNET

STEP 3

PIVOT NUT

Open Bonnet.

STEP 2

ADJUSTING BOLT

Loosen the alternator-adjusting bolt.

Loosen the alternator pivot nut and push the alternator toward the engine to remove the belt.

STEP 4

Install new fan belt and adjust the belt tension. See Fan Belt Adjustment in this manual for instructions.

106

Image 114

Cub Cadet 7530, 7532 manual Fan Belt Replacement

Contents

Series Manufacturer Statement Owner ’s warranty responsibility Length of Coverage Maintenance Turn Right Turn Left Rear Right Serial Numbers General Table of Contents Safety Precautions General Operating Safety PrecautionBasic Safety Requirements For Maintenance Cover the PTO shaft with a guard when not using SAFETY/DECALS SAFETY/DECALS SAFETY/DECALS Steering and Turning the Tractor SAFETY/DECALS Decals AT T E R I E S C O N TA I N a C I D a N D E X P L O S I V E Rotating Machine Parts Tractor Roll Over Roll Over Protective Structure Rops Foldable Rops Frame Low Clearance Positions Step Engine Lubrication System Diesel EngineGeneral Fuel System Cooling System Power TrainAir Intake System Tractor Brakes Differential Lock ClutchMechanical Front Drive MFD Steering Hydraulic System Rear Power Takeoff PTOMid Power Takeoff PTO Option Drawbar 7532 1365 mm Inch Height To top of Rops 7530 2110 mm Instruments and Indicators Tachometer and Hourmeter Engine Coolant Temperature Gauge Turn Signal IndicatorsFuel Gauge Engine Glow Plug Indicator Engine OIL Pressure IndicatorIndependent PTO Clutch Indicatorgear Drive only Control Switches Operating Controls Engine Speed Control Lever Flasher Control Button Turn Signal Switch Control Levers and Pedals Gear Drive Hydrostatic Drive Accelerator Pedal Gear Drive only Brake Pedals Brake Pedal Lock Park Brake Lever Hydrostatic Drive Clutch Pedal Clutch Lock Latch Control Levers Gear Drive Hydrostatic Drive INSTRUMENTS/CONTROLS PTO Switch MID PTO Control Lever if Equipped Gear Drive Hydrostatic Drive Hitch Control Lever Differential Lock Pedal Gear Drive Hydrostatic Drive MFD Control Lever Hydraulic Flow Control Knob Operators Seat Steering Column Tilt Before Starting the Engine RUN in Procedure Normal Starting Procedure Step Push the clutch pedal down Operating Instruction Stopping the Engine Cold Temperature Operation Keep Engine AT Correct Operating Temperature Warming the Engine and TransmissionStopping the Engine HOW to Transport Tractor Towing Gear Drive Transmission Transmission Operation Hydrostatic Drive Transmission To Engage the Differential Lock Differential LockGear Drive To Disengage the Differential Lock Disengage the Rear PTO Power Takeoff PTOEngage the Rear PTO AS Follows AS Follows Engage the MID PTO AS Follows Disengage the MID PTO AS Follows Power Takeoff Guards PTO Operating Safety Three Point Hitch Connecting ImplementsDrawbar Connecting Implements Drawbar With MID PTOWithout MID PTO Flasher Control Button Lamp Switch Turn Signal Connecting Implement to Drawbar PTO RPM PTO Shaft Diameter Dimension a Safety Chain Three Point Hitch System Hitch System Adjustments Lift Links Upper Link Stabilizer Connecting Implement to Hitch Disconnecting Implement from HitchHitch Operation Hitch Control Lever Hitch Lowering Speed Adjustment Hydraulic Block Adding Fluid after Connecting Cylinders and Hoses Tire Inflation Specifications Tire and RIM Equipment Tire Load Capacity PLYPressure PLY Tire Inflation Procedure Check Air Pressure Wheel Mounting Torques Front Wheel Adjustment Bolts and Nuts Positions Torque Front Axle Type Toe-in AdjustmentTo Check the TOE-IN, USE the Following Procedure MFD RH Side Tractor Equipped with Adjustable Wheels Tire Size COMBINATIONS-MFD Tire Size Style Supplier Front End Weights Tractor Ballast TIRES/WHEELS/SPACING/BALLAST Hood Lubrication Table Service Hour Interval Engine Hour meter Service After First 50 Hours System Capacities System Frequency in Hours Page Page Service Specifications Engine Oil Level Engine Oil Change Engine Oil Filter Cooling System Pressure Cooling System Coolant Solutions Cleaning The Cooling System Fuel System Water Removal from the Filter Cup Diesel Fuel Specifications Specifications For Acceptable Number Two Diesel Fuel Fuel Filter Element Replacement Fuel System Air Removal Fuel Injection Pump and Nozzle Check AIR Induction System Dump Valve Air Filter Element Removal Element Cleaning System Inspection Transmission Oil Level Hydrostatic Drive Transmission & Hydraulic LubricationTransmission Oil Level Gear Drive Stou OIL Transmission Oil Change Start the engine and check for leaks Hydraulic Filter Gear & Hydrostatic Drive Change the Hydraulic Filter AS Follows Hydrostatic System Filter Hydrostatic Drive Front Axle Lubrication MFD Front Axle Oil Level Front Axle Oil Change Grille Screens and Radiator Area Fan Belt Adjustment Rotating fan and belts. Contact can injure. Keep clear Fan Belt Replacement Clutch Pedal Adjustment Free Movement Adjustment Brake Pedal Adjustment Raise Stop Setting Position Specifications Electrical System General Service Information Alternator Charging System Fuses Line Fuse Battery Auxiliary Battery Connections Battery Cables and Terminals Removal and Installation of Battery When Charging the Battery When Battery Is Not in Use Storing the Tractor Removing from Storage