Brake Pedal Adjustment | Cub Cadet 7530, 7532 instruction

	MAINTENANCE/ADJUSTMENTS
	MAINTENANCE/ADJUSTMENTS
BRAKE PEDAL ADJUSTMENT
Service Specifications
Brake Pedal Check and Adjustment Interval	Every 200 hours or yearly
Free Pedal Movement Specification	35mm (1.4inch)

Brake pedal free play is very important and must be checked at the recommended intervals. If there is no free movement, the brake shoes will wear quickly.

If there is too much free movement, accidents may occur. If there is not the same free movement between LH pedal and RH pedal, it may cause serious accidents.

Put the tractor on level ground, move the range lever in the L position. Stop the engine.

Loosen lock nut and rotate the brake rod to make a free play of 20 to 30 mm (0.79 to 1.18 in.) at the brake pedal. With this much play obtained, tighten the lock nut.

	BRAKE	ADJUSTING NUT
	ROD	ADJUSTING NUT
	ROD

Confirm that the right and left brakes operate simultaneously by running the tractor.

If not, adjust both of them by means of the brake rods.

108

Image 116

Cub Cadet 7530, 7532 manual Brake Pedal Adjustment

Contents

Series Manufacturer Statement Owner ’s warranty responsibility Length of Coverage Maintenance Turn Right Turn Left Rear Right Serial Numbers General Table of Contents Basic Safety Requirements For Maintenance Safety PrecautionsGeneral Operating Safety Precaution Cover the PTO shaft with a guard when not using SAFETY/DECALS SAFETY/DECALS SAFETY/DECALS Steering and Turning the Tractor SAFETY/DECALS Decals AT T E R I E S C O N TA I N a C I D a N D E X P L O S I V E Rotating Machine Parts Tractor Roll Over Roll Over Protective Structure Rops Foldable Rops Frame Low Clearance Positions Step Diesel Engine GeneralEngine Lubrication System Fuel System Power Train Air Intake SystemCooling System Tractor Brakes Clutch Mechanical Front Drive MFDDifferential Lock Steering Rear Power Takeoff PTO Mid Power Takeoff PTO OptionHydraulic System Drawbar 7532 1365 mm Inch Height To top of Rops 7530 2110 mm Instruments and Indicators Tachometer and Hourmeter Fuel Gauge Engine Coolant Temperature GaugeTurn Signal Indicators Independent PTO Clutch Indicatorgear Drive only Engine Glow Plug IndicatorEngine OIL Pressure Indicator Control Switches Operating Controls Engine Speed Control Lever Flasher Control Button Turn Signal Switch Control Levers and Pedals Gear Drive Hydrostatic Drive Accelerator Pedal Gear Drive only Brake Pedals Brake Pedal Lock Park Brake Lever Hydrostatic Drive Clutch Pedal Clutch Lock Latch Control Levers Gear Drive Hydrostatic Drive INSTRUMENTS/CONTROLS PTO Switch MID PTO Control Lever if Equipped Gear Drive Hydrostatic Drive Hitch Control Lever Differential Lock Pedal Gear Drive Hydrostatic Drive MFD Control Lever Hydraulic Flow Control Knob Operators Seat Steering Column Tilt Before Starting the Engine RUN in Procedure Normal Starting Procedure Step Push the clutch pedal down Operating Instruction Stopping the Engine Cold Temperature Operation Stopping the Engine Keep Engine AT Correct Operating TemperatureWarming the Engine and Transmission HOW to Transport Tractor Towing Gear Drive Transmission Transmission Operation Hydrostatic Drive Transmission Differential Lock Gear DriveTo Engage the Differential Lock To Disengage the Differential Lock Power Takeoff PTO Engage the Rear PTO AS FollowsDisengage the Rear PTO AS Follows Engage the MID PTO AS Follows Disengage the MID PTO AS Follows Power Takeoff Guards Drawbar Connecting Implements PTO Operating SafetyThree Point Hitch Connecting Implements Without MID PTO DrawbarWith MID PTO Flasher Control Button Lamp Switch Turn Signal Connecting Implement to Drawbar PTO RPM PTO Shaft Diameter Dimension a Safety Chain Three Point Hitch System Hitch System Adjustments Lift Links Upper Link Stabilizer Hitch Operation Connecting Implement to HitchDisconnecting Implement from Hitch Hitch Control Lever Hitch Lowering Speed Adjustment Hydraulic Block Adding Fluid after Connecting Cylinders and Hoses Tire Inflation Specifications Tire and RIM Equipment Pressure PLY Tire Load CapacityPLY Tire Inflation Procedure Check Air Pressure Wheel Mounting Torques Front Wheel Adjustment Bolts and Nuts Positions Torque Toe-in Adjustment To Check the TOE-IN, USE the Following ProcedureFront Axle Type MFD RH Side Tractor Equipped with Adjustable Wheels Tire Size COMBINATIONS-MFD Tire Size Style Supplier Front End Weights Tractor Ballast TIRES/WHEELS/SPACING/BALLAST Hood Lubrication Table Service Hour Interval Engine Hour meter Service After First 50 Hours System Capacities System Frequency in Hours Page Page Service Specifications Engine Oil Level Engine Oil Change Engine Oil Filter Cooling System Pressure Cooling System Coolant Solutions Cleaning The Cooling System Fuel System Water Removal from the Filter Cup Diesel Fuel Specifications Specifications For Acceptable Number Two Diesel Fuel Fuel Filter Element Replacement Fuel System Air Removal Fuel Injection Pump and Nozzle Check AIR Induction System Dump Valve Air Filter Element Removal Element Cleaning System Inspection Transmission & Hydraulic Lubrication Transmission Oil Level Gear DriveTransmission Oil Level Hydrostatic Drive Stou OIL Transmission Oil Change Start the engine and check for leaks Hydraulic Filter Gear & Hydrostatic Drive Change the Hydraulic Filter AS Follows Hydrostatic System Filter Hydrostatic Drive Front Axle Lubrication MFD Front Axle Oil Level Front Axle Oil Change Grille Screens and Radiator Area Fan Belt Adjustment Rotating fan and belts. Contact can injure. Keep clear Fan Belt Replacement Clutch Pedal Adjustment Free Movement Adjustment Brake Pedal Adjustment Raise Stop Setting Position Specifications Electrical System General Service Information Alternator Charging System Fuses Line Fuse Battery Auxiliary Battery Connections Battery Cables and Terminals Removal and Installation of Battery When Charging the Battery When Battery Is Not in Use Storing the Tractor Removing from Storage