DriveRack | dbx Pro 260 guide

SECTION 6

Remote Control

DriveRack

™

Diagram C

Cable Specification: Cat 5 Cable - 4-Twisted Pairs of 24 AWG wire

RJ-45				RJ-45
(8-Position)			White/Orange	(8-Position)
1			White/Orange					1 -VREF
2			Orange			2			-Zone 1
3			White/Green					3	-Zone 2
3			Green					3	-Zone 2
4			Green					4	-Zone 3
4			White/Blue					4	-Zone 3
5			White/Blue			5			-Zone 4
5			Blue			5			-Zone 4
6			Blue	6					-Zone 5
7			White/Brown				7		-Zone 6
8			Brown		8				-GND
8					8				-GND

ZC-BOB	ZC-1	ZC-2	ZC-3	ZC-4
				ZC-4

®

56	480 User Manual

Image 64

dbx Pro 260 user manual DriveRack

Contents

260 Important Safety Instructions Electromagnetic Compatibility Table of Contents DriveRack Intro IntroductionDriveRack DriveRack featuresDefining the 260 DriveRack System Service Contact Info DriveRackIntroduction IntroductionDriveRack Warranty Section Rear Panel Connections Getting StartedFront Panel LCD Display Data WheelFunction Buttons Input Meters Quick Start Output Meters DriveRack System Setup Stereo Sub Speaker Auto EQ Wizard AFS Wizard AFS Select total number of AFS filters Slowly Increase Mixer gain to Desired level DriveRack Section Basic Navigation Modes Editing FunctionsEffect Button Array Overview Navigating the EQ -GEQ and PEQ Navigating the Xover Section Navigating the Other Section Navigating the Dynamics Section Navigating the Delay Section Navigating the Utility/Meters Section Navigating the Wizard Section Navigating the I/O Section Functions Configuring the DriveRack Program DefinitionNavigating Factory Programs Selecting Programs Editing Factory Programs Navigation Modes Store Program Replacing Saving Factory Programs Changes Creating a User Configuration Signal PathSelect Link/Unlink Mono DLY 1.3 10 ms Unused Select Link/Unlink Select Link/UnlinkSelect Route Mono DLY 20 MS 810 ms Unused Select Link/Unlink Route Name Output Ch2 Saving Configuration Changes Name Rock Venue Detailed Detailed Parameters Pre-Crossover EQ Feedback Eliminator Subharmonic Synthesizer Gate Automatic Gain Control AGC Crossover Notch FiltersPost-CROSSOVER PEQ Compressor/Limiter Threshold T -40 to +20dBu Ratio R 1.0 to Inf1Gain G -20 to +20 dB Auto On/Off Attack .01 to 200 m Sec per band or global Hold 0 to 500 m Sec per band or globalRelease 360 to 5 dB / Sec per band or global Peakstop+ On/Off Alignment Delay Input Routing Phase 0 to OutputNoise Level -10 to 10 Mixer and Router Shift On/Off Meters Power Up Modes PUP Program Stored PUP Mute Current Utility LCD Contrast Auto EQ PlotUtilities/Meters 1 LCD Contrast / Auto EQ Plot ZC Setup Panel None 3 ZC Setup Panel 1 ZC-4 Switch 1 2 3 No Change Panel ZC-2 Boost 0dB Cut OutputPanel 1 ZC-3 Select a No Change 4 -6 Security Set Security Level Pre EQ Low Set 260 Device Level High Password Edit High Password Edit Med Password Password Enter Password Program List List Size List Index Prog Change Mode Program List Prog Lock7-8 Program List/Program Change Output Jumpers Setting 8 Output Jumper Switches Insa Comp o+ LIM 0+Zone Controllers Panel Meters Output Trims Net Remote Control Remote Control PC GUI Installation Section GUI Recommended Cable Specifications ZC-Zone Controllers DriveRack Zone Controller Wiring Diagram a Diagram B DriveRack DriveWare Functions Page Guide Application Guide Mono Four-Way w/ Two Aux ZonesHardware Software DriveRack Stereo Tri-amp Stereo with Four Aux Zones Stereo Bi-amp w/ Dual Delay DriveRack DriveRack DriveRackAppendix Factory Reset Power Up Quick Key Options Specifications Appendix a Auto EQ Optimization Tips Look out for Modes Crossover Diagrams Program List/ Speaker Tunings/ Power Amp Tunings Block Diagram Input and Output Diagrams System Setup and Gain Structure Gain Level Jumpers DriveRack Harman International Company