Editing Functions, Basic Navigation Modes | dbx Pro 260 specification

Section 2	Editing Functions	DriveRack	™

Editing

Functions

2.1 Basic Navigation Modes

Navigational aspects of the 260 DriveRack is simple and as follows. 1. FX buttons - This array of 12 FX buttons is your primary mode of directly accessing any effect module. 2. NEXTPG & PREVPG page buttons - Successive presses of the NEXTPG or PREVPG page buttons will move the user from one page to the next in an effect block. 3. Data Wheel - The Data Wheel is used to move through the program menu of the 260 DriveRack. The Data wheel is also used to change the values of the selected parameter by simply rotating the wheel. Pressing the Data wheel will toggle between the available parameters on any selected page of the currently selected effect module.

2.2 Effect Button Array Overview

PREVIOUS PAGE - Moves to the previous page in the currently selected effect menu.

NEXT PAGE - Moves to the next page in the currently selected effect menu.

EQ - Selects the EQ effect menu. This is the EQ section located prior to the crossover section. Successive presses will rotate through the various pre- crossover 28 band EQ and Post-xover PEQ section modules.

XOVER - Selects the Crossover section.

OTHER - This button is used to move to the module insert section module which includes the Notch filter, Subharmonic Synthesizer, AFS (Advanced Feedback Suppression) and Wire (no parameters) modules.

DYNAMICS - Selects the Dynamics effect sections.

Successive presses will move from the Compressor, Gate and AGC (pre-xover) to the AGC and Limiter (post-xover).

DELAY - Selects the Alignment Delay effect module. successive presses will rotate through the Pre and post Delay modules.

I/O - Selects the input and output parameter editing section for all inputs and outputs. Successive presses will move through each input and output.

PROGRAM (Config) - This button is used to enter the Program screen from any sub section within the unit when pressed. When pressed and held, you will enter Config mode.

UTILITY(Meter) - Selects the Utility menu of the 260 DriveRack. When pressed and held, the 260 will enter METER mode.

®

14	DriveRack™ User Manual

Image 22

dbx Pro 260 user manual Editing Functions, Basic Navigation Modes, Effect Button Array Overview

Contents

260 Important Safety Instructions Electromagnetic Compatibility Table of Contents DriveRack Intro IntroductionDriveRack DriveRack featuresDefining the 260 DriveRack System Service Contact Info DriveRackIntroduction IntroductionDriveRack Warranty Section Rear Panel Connections Getting StartedFront Panel Function Buttons LCD DisplayData Wheel Input Meters Quick Start Output Meters DriveRack System Setup Stereo Sub Speaker Auto EQ Wizard AFS Wizard AFS Select total number of AFS filters Slowly Increase Mixer gain to Desired level DriveRack Section Basic Navigation Modes Editing FunctionsEffect Button Array Overview Navigating the EQ -GEQ and PEQ Navigating the Xover Section Navigating the Other Section Navigating the Dynamics Section Navigating the Delay Section Navigating the Utility/Meters Section Navigating the Wizard Section Navigating the I/O Section Functions Navigating Factory Programs Configuring the DriveRackProgram Definition Selecting Programs Editing Factory Programs Navigation Modes Store Program Replacing Saving Factory Programs Changes Select Creating a User ConfigurationSignal Path Link/Unlink Mono DLY 1.3 10 ms Unused Select Link/Unlink Select Link/UnlinkSelect Route Mono DLY 20 MS 810 ms Unused Select Link/Unlink Route Name Output Ch2 Saving Configuration Changes Name Rock Venue Detailed Detailed Parameters Pre-Crossover EQ Feedback Eliminator Subharmonic Synthesizer Gate Automatic Gain Control AGC Crossover Notch FiltersPost-CROSSOVER PEQ Compressor/Limiter Gain G -20 to +20 dB Threshold T -40 to +20dBuRatio R 1.0 to Inf1 Auto On/Off Release 360 to 5 dB / Sec per band or global Attack .01 to 200 m Sec per band or globalHold 0 to 500 m Sec per band or global Peakstop+ On/Off Alignment Delay Input Routing Noise Level -10 to 10 Mixer and Router Phase 0 toOutput Shift On/Off Meters Utilities/Meters Power Up Modes PUP Program Stored PUP Mute CurrentUtility LCD Contrast Auto EQ Plot 1 LCD Contrast / Auto EQ Plot ZC Setup Panel None 3 ZC Setup Panel 1 ZC-3 Select a No Change Panel 1 ZC-4 Switch 1 2 3 No ChangePanel ZC-2 Boost 0dB Cut Output 4 -6 Security Set Security Level Pre EQ Low Set 260 Device Level High Password Edit High Password Edit Med Password Password Enter Password Program List List Size List Index Prog Change Mode Program List Prog Lock7-8 Program List/Program Change Output Jumpers Setting 8 Output Jumper Switches Zone Controllers Panel Insa Comp o+LIM 0+ Meters Output Trims Net Remote Control Remote Control PC GUI Installation Section GUI Recommended Cable Specifications ZC-Zone Controllers DriveRack Zone Controller Wiring Diagram a Diagram B DriveRack DriveWare Functions Page Guide Hardware Application GuideMono Four-Way w/ Two Aux Zones Software DriveRack Stereo Tri-amp Stereo with Four Aux Zones Stereo Bi-amp w/ Dual Delay DriveRack DriveRack DriveRackAppendix Factory Reset Power Up Quick Key Options Specifications Appendix a Auto EQ Optimization Tips Look out for Modes Crossover Diagrams Program List/ Speaker Tunings/ Power Amp Tunings Block Diagram Input and Output Diagrams System Setup and Gain Structure Gain Level Jumpers DriveRack Harman International Company