Commissioning, Overview | Eaton Electrical SC200 specs

Chapter 4

Commissioning

Overview

Topic	Page
Inserting the Access Power Rectifiers	4-2

Pre-Power-Up Check	4-3

Applying AC Power	4-4

Configuring the Power System for Operation	4-4

Applying DC Power to the Load	4-8

	Copyright © 2005-2006 Eaton Corporation. All Rights Reserved.	4-1
	IPN 997-00012-41D December 2006	4-1
	IPN 997-00012-41D December 2006

Image 33

Eaton Electrical SC200 manual Commissioning, Overview

Contents

Data Power Solutions Installation Guide Copyright 2005-2006 Eaton Corporation All Rights Reserved About This Guide About This Guide For Further Information and Technical Assistance Table of Contents Chapter Operations Table of Contents General Description OverviewTopic General Description Data Power Solutions Product Range APS3-05X Rack-Mounted Versions Data Power Solutions Product Range APS3-06X Desktop Versions APS6-05X Rack-Mounted Versions Access Power Rectifiers SM45 Supervisory Module SM45 Supervisory Module Low Voltage Disconnect if applicable Pre-Installation AC Inputs Pre-Installation Batteries if applicable DC Outputs Servicing Inspecting the Equipment and Reporting Damage Installation Installation Mounting the Power SystemRack Installation rack-mounted versions only Location and Environment DC Installation Practices Connecting the DC Load CablesDC Installation Practices APS3-05X and APS6-05X Rack-Mounted Versions Installation DC Load Cable Specifications Fit load cable clamps Connecting the DC Load Cables Fit cables and sleeves Installing the External Batteries if applicable Installing the External Batteries if applicableBattery Sizing Battery Location Battery Fault Protection Connecting the Battery Cables if applicableBattery Cable Specifications Before You Start Prepare cable clamp Connecting the Battery Cables if applicable Connecting the Battery Temperature Sensor Cable Repeat for other battery cables if required Mounting the Battery Temperature Sensor Connecting the Power System to the AC Supply AC InstallationAC Supply Requirements Commissioning Commissioning Inserting the Access Power Rectifiers Pre-Power-Up Check Pre-Power-Up CheckChecklist Configuring the Power System for Operation Applying AC Power Before you start, you need Configuring the Power System for Operation LVD Hotlink Click to …Page Applying DC Power to the Load SM45 Operations SM45 Operations About the SM45 Front Panel To disable the audible indicator when an alarm is active About the SM45 Front PanelTo change the display contrast To exit a display mode To enter a display modeTo scroll within a display mode About Display Modes Viewing System Values Main Display Mode Viewing System Values Main Display ModeTo view system values Rules for displaying alarms and system status Viewing Alarms and System Status Messages Status View ModeImportant note about Rect Comms Lost alarm To view and clear alarms Viewing and Editing Configuration Parameters Viewing and Editing Configuration ParametersTo view and edit a configuration parameter SM45 Operations Communications Communications Options CommunicationsDirect Connection Ethernet SM45 Ethernet Setup DCTools SetupDCTools Setup Properties Direct Connection Ethernet Parameter Configuration Guidelines Setting Up Snmp Traps Entering the sysObjectID of a Power System Entering the sysObjectID of a Power SystemTo enter the sysObjectID of a power system using DCTools Synchronizing the SM45 Real-time Clock To synchronize the SM45 real-time clock using DCTools Maintenance Troubleshooting MaintenanceProblem Possible Cause/s Required Action Troubleshooting LED Config Error Removing a Rectifier Replacing a Rectifier Replacing a Rectifier Pull out the rectifier Inserting a Rectifier Replacing AC Input Fuses Replacing AC Input FusesTo check and replace AC input fuses Replacing the SM45 Real-time Clock Battery Glossary of Alarms Multiple Rectifier Fail Glossary of AlarmsPartial AC Fail Rectifier Comms Lost Rectifier Fail Sensor Fail System Overload Control Function Glossary Battery Current Limit BCL Control Function Glossary Low Volts Disconnect System AC Input SpecificationsSystem DC Output Environment Dimensions H, W, D SpecificationsWeight APR48 Rectifiers Equipment Incident Report SG/03 ISS04 United States of America Worldwide SupportPage Page Page SM45 Front Panel Menu Structure Configuration Mode Edit Mode