Eaton Electrical SC200

Pre-Installation

IPN 997-00012-41D December 2006

Inspecting the Equipment and Reporting Damage

Unpack the power system and inspect it carefully for possible damage that may have

occurred while in transit.

Next, check the equipment against the packing list (supplied with the equipment) and

ensure that you have received the correct type of Access Power Rectifiers (either APR48 or

APU48).

Report any damage or incorrect shipment immediately, using a copy of the Equipment

Incident Report (at the back of this guide) to supply all relevant details. Fax the completed

form to your local Powerware DC product representative.

 Keep the original packaging. You will need it if any equipment needs to be returned to your

local Powerware DC product representative.

Contents

Main Data Power Solutions Installation Guide All Rights Reserved . About This Guide Purpose Audience Scope Related Information For Further Information and Technical Assistance Table of Contents iv Chapter 1 General Description 1-2 Data Power Solutions Product Range APS3-05X (Rack-Mounted Versions) 1-4 APS3-06X (Desktop Versions) APS6-05X (Rack-Mounted Versions) 1-6 Access Power Rectifiers % Retaining Screw (loosen to remove rectifier) " # $ SM45 Supervisory Module 1-8 Low Voltage Disconnect (if applicable) Chapter 2 Pre-Installation 2-2 Warnings AC Inputs Equipment Classification Batteries (if applicable) 2-4 DC Outputs Rectifiers Location and Environment Servicing EMC Compliance 2-6 Chapter 3 Installation 3-2 Mounting the Power System " APS3-05X and APS6-05X power systems come # DC Installation Practices Connecting the DC Load Cables 3-4 APS3-05X and APS6-05X (Rack-Mounted Versions) $ To ensure reliable connections at the terminal blocks of the DC outlets, torque the clamp-screws APS3-06X (Desktop Versions) Step 1 - Fit load cable clamps Step 2 - Strip cable ends 3-8 Connecting the Battery Cables (if applicable) Step 1 - Prepare cable clamp Step 2 Strip cable and fit sleeve Step 3 Terminate cable " 16mm battery cable sleeve. # Battery cable clamp with posts removed. " Terminate the Black/White wire at TEMP SENSOR (+) and the Black wire at # To ensure reliable connections at the battery temperature sensor terminal blocks, torque the 3-12 Connecting the Power System to the AC Supply Chapter 4 Commissioning 4-2 Inserting the Access Power Rectifiers Step 1 Unpack the rectifiers Step 2 Align the rectifier with the burst-out guides in the shelf Step 3 Push in the rectifier Page 4-4 Applying AC Power Configuring the Power System for Operation Using the Front Panel Keypad Using DCTools Step 1 Connect a PC to the RS-232 port of the APS DC power system Step 2 Check that your PC port is specified correctly 4-6 Step 3 Check through the loaded configuration and make changes as required Page 4-8 Applying DC Power to the Load Chapter 5 SM45 Operations 5-2 About the SM45 Front Panel The Keypad and LED Indicators " # $ % ! Urgent Alarm LED (red) indicates one or more active urgent alarms The Display Indicators To disable the audible indicator (when an alarm is active) Display Time-out Changing the Display Contrast To change the display contrast 5-4 Using Edit Mode Viewing System Values (Main Display Mode) To view system values 5-6 Viewing Alarms and System Status Messages (Status View Mode) To view and clear alarms To view system status messages Viewing and Editing Configuration Parameters To view and edit a configuration parameter Page Chapter 6 Communications 6-2 Communications Options DCTools Setup SM45 Ethernet Setup To configure the SM45 for Ethernet communications using DCTools 6-4 Setting Up SNMP Traps Entering the sysObjectID of a Power System To enter the sysObjectID of a power system using DCTools 6-6 Synchronizing the SM45 Real-time Clock To synchronize the SM45 real-time clock using DCTools Chapter 7 Maintenance 7-2 Troubleshooting Page 7-4 Page 7-6 Replacing a Rectifier Removing a Rectifier Step 2 Pull out the rectifier Procedure complete 7-8 Inserting a Rectifier Procedure complete Replacing AC Input Fuses before checking or replacing their respective fuses. CAUTION: DOUBLE-POLE / NEUTRAL FUSING (Bussman ABC-15 or Littelfuse 314-015 Type 3AB) for continued protection against risk of fire. To check and replace AC input fuses 7-10 Dispose of the used battery according to the battery manufacturers instructions. Appendix A Glossary of Alarms A-2 Appendix B Control Function Glossary Battery Current Limit (BCL) Battery Test Equalize Temperature Compensation Appendix C Specifications C-2 EQUIPMENT INCIDENT REPORT Page . Worldwide Support Notes: Notes: Page SM45 Front Panel Menu Structure Main Display Mode Status View Mode Configuration Mode Edit Mode