Communications, Overview | Eaton Electrical SC200 guide

Chapter 6

Communications

Overview

Topic	Page
Communications Options	6-2

DCTools Setup	6-3

SM45 Ethernet Setup	6-3

Setting Up SNMP Traps	6-4

Entering the “sysObjectID” of a Power System	6-5

Synchronizing the SM45 Real-time Clock	6-6

	Copyright © 2005-2006 Eaton Corporation. All Rights Reserved.	6-1
	IPN 997-00012-41D December 2006	6-1
	IPN 997-00012-41D December 2006

Image 49

Eaton Electrical SC200 manual Communications, Overview

Contents

Data Power Solutions Installation Guide Copyright 2005-2006 Eaton Corporation All Rights Reserved About This Guide About This Guide For Further Information and Technical Assistance Table of Contents Chapter Operations Table of Contents Overview General DescriptionTopic General Description Data Power Solutions Product Range APS3-05X Rack-Mounted Versions Data Power Solutions Product Range APS3-06X Desktop Versions APS6-05X Rack-Mounted Versions Access Power Rectifiers SM45 Supervisory Module SM45 Supervisory Module Low Voltage Disconnect if applicable Pre-Installation AC Inputs Pre-Installation Batteries if applicable DC Outputs Servicing Inspecting the Equipment and Reporting Damage Installation Installation Mounting the Power SystemRack Installation rack-mounted versions only Location and Environment Connecting the DC Load Cables DC Installation PracticesDC Installation Practices APS3-05X and APS6-05X Rack-Mounted Versions Installation DC Load Cable Specifications Fit load cable clamps Connecting the DC Load Cables Fit cables and sleeves Installing the External Batteries if applicable Installing the External Batteries if applicableBattery Sizing Battery Location Battery Fault Protection Connecting the Battery Cables if applicableBattery Cable Specifications Before You Start Prepare cable clamp Connecting the Battery Cables if applicable Connecting the Battery Temperature Sensor Cable Repeat for other battery cables if required Mounting the Battery Temperature Sensor AC Installation Connecting the Power System to the AC SupplyAC Supply Requirements Commissioning Commissioning Inserting the Access Power Rectifiers Pre-Power-Up Check Pre-Power-Up CheckChecklist Configuring the Power System for Operation Applying AC Power Before you start, you need Configuring the Power System for Operation LVD Hotlink Click to …Page Applying DC Power to the Load SM45 Operations SM45 Operations About the SM45 Front Panel About the SM45 Front Panel To disable the audible indicator when an alarm is activeTo change the display contrast To exit a display mode To enter a display modeTo scroll within a display mode About Display Modes Viewing System Values Main Display Mode Viewing System Values Main Display ModeTo view system values Rules for displaying alarms and system status Viewing Alarms and System Status Messages Status View ModeImportant note about Rect Comms Lost alarm To view and clear alarms Viewing and Editing Configuration Parameters Viewing and Editing Configuration ParametersTo view and edit a configuration parameter SM45 Operations Communications Communications Communications OptionsDirect Connection Ethernet SM45 Ethernet Setup DCTools SetupDCTools Setup Properties Direct Connection Ethernet Parameter Configuration Guidelines Setting Up Snmp Traps Entering the sysObjectID of a Power System Entering the sysObjectID of a Power SystemTo enter the sysObjectID of a power system using DCTools Synchronizing the SM45 Real-time Clock To synchronize the SM45 real-time clock using DCTools Maintenance Maintenance TroubleshootingProblem Possible Cause/s Required Action Troubleshooting LED Config Error Removing a Rectifier Replacing a Rectifier Replacing a Rectifier Pull out the rectifier Inserting a Rectifier Replacing AC Input Fuses Replacing AC Input FusesTo check and replace AC input fuses Replacing the SM45 Real-time Clock Battery Glossary of Alarms Multiple Rectifier Fail Glossary of AlarmsPartial AC Fail Rectifier Comms Lost Rectifier Fail Sensor Fail System Overload Control Function Glossary Battery Current Limit BCL Control Function Glossary Low Volts Disconnect System AC Input SpecificationsSystem DC Output Environment Dimensions H, W, D SpecificationsWeight APR48 Rectifiers Equipment Incident Report SG/03 ISS04 United States of America Worldwide SupportPage Page Page SM45 Front Panel Menu Structure Configuration Mode Edit Mode