Emerson 1700, 2700 manual

Output Wiring – Model 2700 Configurable I/O Transmitters

Figure 6-7Frequency output – Terminals 5 & 6 (Channel C) – Internal power

+

–

00042

Counter

Output voltage level is +15 VDC ± 3%

Note: See Figure 6-14for output voltage versus load resistance.

Figure 6-8Frequency output – Terminals 5 & 6 (Channel C) – External power

+

Pull-up resistor

000042

+

3–30 VDC

–

Counter

–

Note: Refer to Figure 6-15for recommended resistor versus supply voltage.

CAUTION

Excessive current will damage the transmitter.

Do not exceed 30 VDC input. Terminal current must be less than 500 mA.

46	Micro Motion® Model 1700 and 2700 Transmitters

Image 50

Emerson 1700, 2700 installation manual 7Frequency output Terminals 5 & 6 Channel C Internal power

Contents

Micro Motion Model 1700 Model 2700 Transmitters Page Contents Index Overview SafetyBefore You Begin Flowmeter components Transmitter installation procedures Flowmeter documentation 1Flowmeter documentation resources Micro Motion customer service Installing the Transmitter Installation architecture 1Installation types AC power requirements Temperature limitsPower source Determining an appropriate location DC power requirements 1Typical power cable resistances at 68 F 20 C 2Maximum cable lengths Accessibility for maintenanceMaximum cable lengths Mounting the transmitter Integral installations 2Rotating the transmitter 34-wire remote Wall mount or pipe mount 3 9-wire remote installations 59-wire remote Wall mount or pipe mount 6Transmitter/core processor assembly Exploded view Mounting the remote core processor 7Remote core processor Wall mount or pipe mount Grounding the flowmeter components 3Grounding methods for flowmeter components Supplying power Rotating the display Installing the Transmitter 10Display components Wiring the Transmitter to the Sensor Cable types Wiring for 4-wire remote installations 1 4-wire cable2 9-wire cable 3Wiring to the mating connector Wiring for 9-wire remote installations Core processor on transmitter Subtask 1 Wire the remote core processor to the transmitter 5Cable glands 7Wrapping the shield drain wires 10Gland body and core processor housing Subtask 2 Wiring the sensor to the remote core processor 129-wire cable between sensor and core processor Wiring the Transmitter to the Sensor Output terminals and output types Output Wiring Model 1700/2700 Analog TransmittersOutput wiring 1Terminals and output types 1Basic analog wiring 2HART/analog single-loop wiring Smart Family Output Wiring Intrinsically Safe Safe area output wiring Safe area mA output wiring 2Safe area mA output load resistance values Safe area frequency/discrete output wiring 5Safe area frequency/discrete output wiring Hazardous area output wiring Hazardous area safety parameters Hazardous area current 2Safety parametersHazardous area voltage Hazardous area capacitance Hazardous area mA output wiring Hazardous area frequency/discrete output wiring Hazardous area Output Wiring Model 2700 Configurable I/O Transmitters Channel configuration 1Channel configuration MA output wiring 2Basic mA wiring Frequency output wiring 5Frequency output Terminals 3 & 4 Channel B Internal power 7Frequency output Terminals 5 & 6 Channel C Internal power Discrete output wiring 9Discrete output 1 Terminals 3 & 4 Channel B Internal power 11Discrete output 2 Terminals 5 & 6 Channel C Internal power Volts Voltage Output Level High Discrete input wiring 2Input voltage ranges for external power 16Discrete input Terminals 5 & 6 Channel C Internal power Micro Motion Model 1700 and 2700 Transmitters Foundation fieldbus wiring 1Connecting the fieldbus communication wires PROFIBUS-PA wiring 2Connecting the PROFIBUS-PA communication wires Power connection SpecificationsFunctional specifications Service port connection Fisco and Fnico approval Input/output signals Input signal from sensorCore processor connection Specifications Operating Absolute minimum = 100 Ohms for V supply 25.6 volts Specifications HART/Bell202 Service portDigital communication Foundation fieldbus or PROFIBUS-PA transmitters Ambient temperature effect Power supplyEnvironmental requirements Ambient temperature limits EMC compliance Outputs UL and CSATransmitter Atex and IECEx Housing Performance specificationsPhysical specifications Mounting Interface/display WeightDimensions Dimensions in inchesmm Inches Dimensions in mm Or M20 × 11/16 160 13/16 139 ″-14 NPT 158 182 × Ø3/8 13/16 148 15/16 × 1/2″-14 NPT Figure A-5Dimensions Remote core processor Index Atex Remote core processor with remote Index Micro Motion Model 1700 and 2700 Transmitters Page 20001700