Enterasys Networks X-PeditionTM XSR2 Configuration, Configure the dialer list and ACL for DoD

Configuring BAP

XSR1(config-controller<T1-1/0>)#isdn bchan-number-order ascending XSR1(config-controller<T1-1/0>)#no shutdown XSR1(config-controller<T1-1/0>)#dialer pool-member 1 priority 0

2.Configure BRI interface 2/0 with the basic-ni1switch type and two SPIDs:

XSR1(config)#interface bri 2/0 XSR1(config-if<BRI-2/0>)#isdn switch-type basic-ni1 XSR1(config-if<BRI-2/0>)#isdn spid1 0337250001 XSR1(config-if<BRI-2/0>)#isdn spid2 0337250101 XSR1(config-if<BRI-2/0>)#no shutdown XSR1(config-if<BRI-2/0>)#dialer pool-member 1 priority 0

3.Configure the Dialer 1 interface with a dialer pool:

XSR1(config)#interface Dialer1 XSR1(config-if<D1>)#no shutdown XSR1(config-if<D1>)#dialer pool 1 XSR1(config-if<D1>)#encapsulation ppp

4.Set up BAP on Dialer 1 by specifying the load-threshold (BoD), enabling BAP, and configuring XSR1 to initiate the addition of a link. Note that the load threshold is very low, ensuring that BAP will be enabled relatively quickly when traffic starts to build.

XSR1(config-if<D1>)#multilink load-threshold 4 XSR1(config-if<D1>)#ppp multilink bap XSR1(config-if<D1>)#ppp bap call request

5.Complete Dialer 1 configuration by setting the idle timeout and dialer-group values for DoD:

XSR1(config-if<D1>)#dialer idle-timeout 4000 XSR1(config-if<D1>)#dialer-group 2 XSR1(config-if<D1>)#ip address 99.99.1.2 255.0.0.0

6.Configure the dialer list and ACL for DoD:

XSR1(config-if<D1>)#access-list 102 permit icmp list 102 XSR1(config-if<D1>)#dialer-list 2 protocol ip list 102

XSR2 Configuration

XSR2 is configured to accept incoming calls only.

1.Begin configuring XSR2 by setting up the T1 controller (PRI interface):

XSR1(config)#controller t1 1/0 XSR2(config-controller<T1-1/0>)#pri-group XSR2(config-controller<T1-1/0>)#isdn bchan-number-order ascending XSR2(config-controller<T1-1/0>)#no shutdown XSR2(config-controller<T1-1/0>)#dialer pool-member 1 priority 0

2.Configure BRI interface 2/0 with the basic-ni1switch type and two SPIDs:

XSR2(config)#interface bri 2/0 XSR2(config-if<BRI-2/0>)#isdn switch-type basic-ni1 XSR2(config-if<BRI-2/0>)#isdn spid1 0337250001 XSR2(config-if<BRI-2/0>)#isdn spid2 0337250101 XSR2(config-if<BRI-2/0>)#no shutdown XSR2(config-if<BRI-2/0>)#dialer pool-member 1 priority 0

XSR User’s Guide 8-15