Extron electronic Ultra Series Command/response table for IP-specific SIS commands \⤀, X5$ ,X5%

Command/response table for IP-specific SIS commands (continued\⤀

Command	ASCII command	Response	Additional
	(host to switcher\⤀	(switcher to host\⤀	description

IP setup commands (continued\⤀

Set e-mail events for

recipient

Example:

CrossPoint 450 Plus 3232

EX4!,X4#,X4$,X4$,...,X4$EM}

IpeX4%]

E72,3,1,2,8,32,98,99,EM}

Ipe•Jsmith@folklore.net]

You must first have set an e-mail recipient for the e-mail account number (X4!), using the separate Set e-mail recipient (CR) command.

E-mail account #72, JSmith, will receive fail/missing and fixed/restored messages for input signals 1, 2, 8, and 32; fans; and power supplies.

Read e-mail events for recipients

Response description:

Example:

CrossPoint 450 Plus 3232

EX4!EM} X4$,X4$,X4$, ... ,X4$]

Notify-what? inputs 1-32 (inputs above the matrix size are always zero) fans PS]

E7@EM} See below

Notify failed and fixed					E-mail input 8 status													Ignore input 16															E-mail power supply and fan status
Response:		1	1	0	0	0	0		0
	3,									1	0		0	0	0	0		0		0		0	0			0	0			0	0	0	0	0	0	0	0	0	0	0	0	1	1	1
Input: 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
																																												Fans
																																							Power Supplies
Example:				E7@EM}															See below
MAV Plus 1616
				Notify failed and fixed													E-mail input 8 status																Ignore input 16
							Response:						1	1	0	0		0		0		0				0			0	0	0	0	0	0
												3,												1											0	1
										Input: 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 Power Supply
Set DHCP on or off				EX4^DH}															IdhX4^]
Read DHCP on/off status				EDH}															X4^]
Set serial port parameters				EX4&*X4*,X4(,X5),X5!CP}
								CP											CpnX4&•CcpX4*,X4(,X5),X5!]
Read serial port parameters									}										X4*		,	X4(		,	X5)			,	X5!]
				EX4&
Configure flow control				EX4&*X5$,X5%CF]															CpnX4&•CflX5$,X5%]
Read flow control				ECF															X5$,X5%]
Configure receive timeout				EX4&*X5^,X5&CE]															CpnX4&•CceX5^,X5&]
Read receive timeout				ECE															X5^,X5&]
Set mode				EX4&*X5@CY}															CpnX4&•CtyX5@]
Read mode				EX4&CY}															X5@]
Set verbose mode				EX5#CV}															VrbX5#]
Read verbose mode				ECV}															X5#]
Configure current port				E0*X5*TC}															Pti0*X5*]
timeout
Read current port timeout				E0TC}															X5*]
Configure global IP port				E1*X5*TC}															Pti1*X5*]
timeout
Read global IP port timeout				E1TC}															X5*]

CrossPoint / MAV Matrix Switchers • Programmer’s Guide 4-25