Manuals / Extron electronic / Computer Equipment / Switch

Extron electronic MAV Plus Series manual Ethernet Connection, Ethernet Link, Default address

Models: Ultra Series MAV Plus Series

1 214

Download 214 pages 8.93 Kb

Page 184

Ethernet Connection

Ethernet Connection

Ethernet Link

The rear panel Ethernet connector on the

CrossPoint or MAV switcher can be connected to an Ethernet LAN or WAN. This connection makes SIS control

of the switcher possible using a computer connected to the same LAN.

ETHERNET

LINK ACT

Ethernet connection

The Ethernet cable can be terminated as a straight-through cable or a crossover cable and must be properly terminated for your application (figure A-1).

•Crossover cable — Direct connection between the computer and the CrossPoint or MAV switcher.

•Patch (straight-through) cable — Connection of the CrossPoint or MAV switcher to an Ethernet LAN.

Patch (straight) cable

												Side 1			Side 2
											Pin	Wire color		Pin	Wire color
											1	White-orange		1	White-orange
Side
Side											2	Orange		2	Orange
										RJ-45	2	Orange		2	Orange
										RJ-45	3	White-green		3	White-green
										connector
										connector
											4	Blue		4	Blue
											4	Blue		4	Blue

											5	White-blue		5	White-blue



											6	Green		6	Green
											6	Green		6	Green

											7	White-brown		7	White-brown
											7	White-brown		7	White-brown

											8	Brown		8	Brown

Insert		Crossover cable
twisted		Side 1			Side 2
pair wires.		Side 1			Side 2
pair wires.	Pin	Wire color		Pin	Wire color
	Pin	Wire color		Pin	Wire color
	1	White-orange		1	White-green

	2	Orange		2	Green

	3	White-green		3	White-orange
	4	Blue		4	Blue

	5	White-blue		5	White-blue

	6	Green		6	Orange

	7	White-brown		7	White-brown

	8	Brown		8	Brown

Figure A-1 — RJ-45 connector pinout tables

Default address

To access the CrossPoint or MAV switcher via the LAN port, you need the switcher’s IP address. If the address has been changed to an address comprised of words and characters, you can determine the actual numeric IP address using the Ping utility. If the address has not been changed, the factory-specified default is 192.168.254.254.

Ping can also be used to test the Ethernet link to the CrossPoint or MAV switcher.

A-2 CrossPoint / MAV Matrix Switchers • Ethernet Connection

Image 184

Extron electronic MAV Plus Series, Ultra Series Ethernet Connection, Ethernet Link, Default address, Ethernet connection

Contents

CrossPoint 450 Plus Series CrossPoint Ultra Series MAV Plus Series Matrix Switchers68-521-20 Rev. A Precautions Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschFCC Class A Notice Page Front Panel Configuration PortMatrix Sizes up to 1616 Only Table of ContentsCrossPoint / MAV Matrix Switchers Table of Contents Table of Contents, cont’d Viewing and adjusting the input audio level audio modelsViewing and adjusting the output volume audio models Plasma display S-video problem CrossPoint switchersCommand/Response Table for IP-specific SIS Commands CrossPoint / MAV Matrix Switchers Table of ContentsTable of Contents, cont’d iv CrossPoint / MAV Matrix Switchers Table of ContentsCrossPoint / MAV Matrix Switchers Table of Contents vi CrossPoint / MAV Matrix Switchers Table of Contents Table of Contents, cont’d68-521-20 A CrossPoint / MAV Matrix Switchers About this Manual About the CrossPoint / MAV Matrix SwitchersDefinitions Features Chapter1OneAbout the Matrix Switchers IntroductionAbout this Manual 1-2 CrossPoint / MAV Matrix Switchers IntroductionMatrix Switcher Extron CrossPoint Ultra 128 HVAFigure 1-1 - Typical CrossPoint Ultra matrix switcher application CrossPoint / MAV Matrix Switchers IntroductionIntroduction, cont’d Extron MAV Plus 1616 HDA16 Outputs 16 InputsCrossPoint Ultra switchers CrossPoint / MAV Matrix Switchers IntroductionCrossPoint 450 Plus switchers MAV Plus switchers1-6 CrossPoint / MAV Matrix Switchers Introduction Introduction, cont’dThe MAV Plus Series switchers have a bandwidth of 150 MHz -3 dB CrossPoint / MAV Matrix Switchers IntroductionMAV 1212 Plus 12 inputs by 12 outputs MAV 1616 Plus 16 inputs by 16 outputsFeatures DefinitionsConfiguration - One or more ties or one or more sets of ties 1-8 CrossPoint / MAV Matrix Switchers IntroductionCrossPoint / MAV Matrix Switchers Introduction Digital Sync Validation Processing DSVP CrossPointInput # Figure 1-3 - DSVP data displayIntroduction, cont’d 1-10 CrossPoint / MAV Matrix Switchers IntroductionSIS for easy programming and operation Power supply status LEDs Primary and redundant power suppliesCrossPoint / MAV Matrix Switchers Introduction 1-12 CrossPoint / MAV Matrix Switchers Introduction Introduction, cont’dInstallation Mounting the Switcher Rear Panel Views Rear Panel ConnectionsFront Panel Configuration Port Chapter2TwoInstallation Mounting the SwitcherUL guidelines 2-2 CrossPoint / MAV Matrix Switchers InstallationMounting instructions 2. Secure the switcher to the rack using the supplied boltsFigure 2-1 - Installing the switcher in a rack CrossPoint / MAV Matrix Switchers InstallationInstallation, cont’d Rear Panel ViewsCrossPoint 450 Plus switchers Figure 2-2 - CrossPoint 450 Plus 3232 HVA matrix switcherCrossPoint Ultra switchers Figure 2-3 - CrossPoint Ultra 1616 HVA matrix switcherswitcher Figure 2-4 - CrossPoint Ultra 128 HVA matrix switcherInstallation, cont’d MAV Plus switchersFigure 2-5 - MAV Plus 3232 SVA matrix switcher Figure 2-6 - MAV Plus 3232 matrix switchers with various formatsFigure 2-7 - MAV Plus 1616 HDA matrix switcher Figure 2-8 - MAV Plus 1616 matrix switchers with various formatsCrossPoint / MAV Matrix Switchers Installation RESETInstallation, cont’d Figure 2-9 - MAV Plus 128 AV RCA matrix switcherFigure 2-10 - MAV Plus 128 HDA matrix switcher Figure 2-11 - MAV Plus 128 matrix switchers with various formatsVideo input and output video switchers\⤀ Rear Panel ConnectionsRGBHV CrossPoint switchers\⤀ CrossPoint / MAV Matrix Switchers InstallationInstallation, cont’d 2-10 CrossPoint / MAV Matrix Switchers InstallationCrossPoint 450 Plus 2412, 2424, 3216 CrossPoint UltraVideo MAV Plus switchers\⤀ CrossPoint / MAV Matrix Switchers InstallationVideo inputs - Connect component/HDTV video figure Video outputs - Connect component/HDTV video figureInstallation, cont’d 2-12 CrossPoint / MAV Matrix Switchers InstallationFigure 2-14 - MAV Plus S-video connections Figure 2-15 - MAV Plus video connectionsSync termination switches CrossPoint\⤀ Sync termination switches - The RGB CrossPoint matrix switchers haveFigure 2-16 - Sync termination switches CrossPoint / MAV Matrix Switchers InstallationAudio input and output audio models\⤀ Installation, cont’dCaptive screw connector models all except MAV Plus 128 AV RCA\⤀ Figure 2-17 - Captive screw connector wiring for audio inputsFigure 2-19 - Captive screw connector wiring for audio output RCA connector model MAV Plus 128 AV RCA\⤀CrossPoint / MAV Matrix Switchers Installation Connections for balanced and unbalanced audio outputs - These 3.5 mmRS-232/RS-422 EthernetInstallation, cont’d D connector for serial RS-232/RS-422 control figureCabling and RJ-45 connector wiring Figure 2-21 - RJ-45 connector and pinout tablesCrossPoint / MAV Matrix Switchers Installation 10Base-T Ethernet requires CAT 3 UTP or STP cable at minimumReset button 2-18 CrossPoint / MAV Matrix Switchers InstallationN Hard reset does not clear the current configuration Matrix SwitcherCrossPoint / MAV Matrix Switchers Installation PowerFigure 2-23 - Multiple device external sync connection example Front Panel Configuration Port Matrix Sizes up to 1616 Only\⤀ Installation, cont’dFigure 2-24 - Front panel configuration port 2-20 CrossPoint / MAV Matrix Switchers InstallationThis port is RS-232 only, with its default protocols as follows CrossPoint / MAV Matrix Switchers Installation9600 baud no parityInstallation, cont’d 2-22 CrossPoint / MAV Matrix Switchers InstallationFront Panel Controls and Indicators Front Panel Operations Troubleshooting Configuration WorksheetsChapter3Three OperationFront Panel Controls and Indicators Operation3-2 CrossPoint / MAV Matrix Switchers Operation Figure 3-1 - Front panel, CrossPoint Ultra 128 HVAA B C D E F G HPower Supply LEDs - See page CrossPoint / MAV Matrix Switchers OperationOperation, cont’d Input and output buttons3-4 CrossPoint / MAV Matrix Switchers Operation Lit A preset has already been saved to this locationCrossPoint switchers, Input 1 through 10 Display the RGB delay. See CrossPoint / MAV Matrix Switchers OperationControl buttons Save configuration or preset changes that you make on the front panel3-6 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dPreset button - The Preset button has two primary functions and three CrossPoint / MAV Matrix Switchers OperationI/O controls 3-8 CrossPoint / MAV Matrix Switchers OperationOperation, cont’d Primary functionsCrossPoint switchers Selects the RGB delay mode, in which you can CrossPoint / MAV Matrix Switchers Operationset the RGB delay. See “Setting RGB delay CrossPoint Switchers” on With the RGBHV/Video button, commands the front panel system resetPower indicators 2412 and larger models only\⤀ Button iconsI Primary and Redundant Power Supply LEDs 3-10 CrossPoint / MAV Matrix Switchers OperationFront Panel Operations DefinitionsConfiguration - One or more ties or one or more sets of ties CrossPoint / MAV Matrix Switchers OperationFront panel security lockouts Power3-12 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dCreating a configuration Select to configure video, audio, or both by pressing the RGBHVCrossPoint switchers or Video MAV Plus switchers button and/or Audio CrossPoint / MAV Matrix Switchers Operation1 2 3 4 5 6 7 8 15 16 17 18 19 20 21 22 23 24 31 3-14 CrossPoint / MAV Matrix Switchers OperationOperation, cont’d Example 1 Creating a set of video and audio tiesThe current configuration figure 3-10 is now Figure 3-10 - Example 1, final configurationCrossPoint / MAV Matrix Switchers Operation ENTER PRESET VIEW1 2 3 4 5 6 7 8 3-16 CrossPoint / MAV Matrix Switchers OperationOperation, cont’d 1 2 3 4 5 6 7 8The current configuration figure 3-16 is now Figure 3-16 - Example 2, final configurationCrossPoint / MAV Matrix Switchers Operation 4. Press and release the output 1 button figure3-18 CrossPoint / MAV Matrix Switchers Operation Operation, cont’d1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8Figure 3-22 - Example 3, final configuration, audio switcher CrossPoint / MAV Matrix Switchers Operation4. Press and release the output 4 button figure Figure 3-20 - Deselect the output3-20 CrossPoint / MAV Matrix Switchers Operation Viewing a configurationOperation, cont’d 1 2 3 4 5 6 7 8 15 CrossPoint / MAV Matrix Switchers OperationExample 4 Viewing video and audio, audio only, and video only ties Figure 3-23 - Clear all selections3-22 CrossPoint / MAV Matrix Switchers Operation Operation, cont’d1 2 3 4 5 6 7 1 2 3 4 5 6 7 8CrossPoint / MAV Matrix Switchers Operation 1 2 3 4 5 6 7 87. Press and release the View button to exit View-only mode figure Figure 3-28 - Press the View button to exit View-only modeI/O grouping 3-24 CrossPoint / MAV Matrix Switchers OperationOperation, cont’d 1 2 3 4 5 6 7 8 9Press the Preset button to select group CrossPoint / MAV Matrix Switchers Operation3. Press and release one of the Control buttons to select a group Press the Enter button to select group3-26 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dExample 5 Grouping inputs and outputs Figure 3-30 - Clear all selectionsCrossPoint / MAV Matrix Switchers Operation 1 2 3 4 5 6 7 8 151 2 3 4 5 6 7 8 15 1 2 3 4 5 6 7 8Setting RGB delay CrossPoint switchers\⤀ 3-28 CrossPoint / MAV Matrix Switchers OperationOperation, cont’d Figure 3-36 - Deselect I/O Group mode22 23 24 Example 6 Setting the RGB delay for an outputFigure 3-38 - Select RGB Delay mode CrossPoint / MAV Matrix Switchers OperationFigure 3-40 - Adjust the RGB delay interval Figure 3-41 - Deselect RGB Delay mode3-30 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dUsing presets 10 11 12 13 14 1517 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Figure 3-42 - Preset locations by matrix sizeExample 7 Saving a preset Figure 3-44 - Enter Save Preset modeFigure 3-45 - Select the preset 3-32 CrossPoint / MAV Matrix Switchers OperationExample 8 Recalling a preset Figure 3-48 - Enter Recall Preset modeCrossPoint / MAV Matrix Switchers Operation Figure 3-46 - Press the Enter button1 2 3 4 15 Figure 3-49 - Select the preset3-34 CrossPoint / MAV Matrix Switchers Operation recall the presetMuting and unmuting video and/or audio outputs CrossPoint / MAV Matrix Switchers OperationIndividual outputs can be muted or unmuted as follows Press and release the View button3-36 CrossPoint / MAV Matrix Switchers Operation Operation, cont’d1 2 3 4 5 6 7 8 15 Example 9 Muting and unmuting an audio/RS-232 outputCrossPoint / MAV Matrix Switchers Operation Figure 3-53 - Mute the outputsFigure 3-54 - Unmute the outputs 6. Press and release the View button to exit View-only mode figureViewing and adjusting the input audio level audio models\⤀ 3-38 CrossPoint / MAV Matrix Switchers OperationOperation, cont’d Figure 3-56 - Audio gain and attenuationExample 10 Viewing and adjusting an input audio level CrossPoint / MAV Matrix Switchers OperationFigure 3-57 - Clear all selections Figure 3-58 - Select Audio modeInput audio level adjustment displays 3-40 CrossPoint / MAV Matrix Switchers OperationOperation, cont’d CrossPoint 450 PlusInput audio level adjustment displays CrossPoint / MAV Matrix Switchers Operation= Unlit button = Blinking buttonFigure 3-60 - Level display on a 16-output-button switcher Figure 3-61 - Level display on a 8-output-button switcher3-42 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dFigure 3-62 - Adjust the input audio level Figure 3-63 - Level display on a 16-output-button switcherFigure 3-64 - Level display on a 8-output-button switcher CrossPoint / MAV Matrix Switchers OperationViewing and adjusting the output volume audio models\⤀ 3-44 CrossPoint / MAV Matrix Switchers OperationOperation, cont’d Figure 3-65 - Deselect Audio modeReading the displayed volume Push Esc button again - 5.5% + 1.5% = 7% volumePush Esc button twice more - 7% + 1.5% + 1.5% = 10% volume Push Esc button nineteen times more - 10% + 191.5% = 38.5% volume3-46 CrossPoint / MAV Matrix Switchers Operation Audio volume adjustment settingsOperation, cont’d CrossPoint / MAV Matrix Switchers Operation 63 dB of attenuation is applied to the outputExample 11 Viewing and adjusting an output volume level 3-48 CrossPoint / MAV Matrix Switchers OperationPRESET Operation, cont’d10 11 10 1113 14 15 Figure 3-69 - Volume display on a 16-input-button switcherFigure 3-71 - Adjust the output audio volume Figure 3-72 - Volume display on a 16-input-button switcher3-50 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dCrossPoint / MAV Matrix Switchers Operation Fast Blinking Button 26 dB attenuation 61% volume10 11 5. Press and release the Audio button figureSetting the front panel locks Executive modes\⤀ 3-52 CrossPoint / MAV Matrix Switchers OperationOperation, cont’d Selecting Lock mode 2 or toggling between mode 2 and modePerforming a system reset from the front panel Figure 3-77 - System resetCrossPoint / MAV Matrix Switchers Operation Selecting Lock mode 2 or toggling between mode 2 and modeBackground illumination Selecting the rear panel Remote port protocol and baud rate3-54 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dRear Panel Operations See the following table for a summary of the modesReset Mode Comparison/Summary 3-56 CrossPoint / MAV Matrix Switchers OperationThe switcher reverts to the factory default Mode 3 turns events on or off. During resettingPerforming soft system resets resets 3, 4, and 5\⤀ Perform a soft reset of the switcher as followsFigure 3-82 - Whole switcher and absolute resets CrossPoint / MAV Matrix Switchers OperationPerforming a hard reset Figure 3-83 - Hard reset3-58 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dTroubleshooting Plasma display S-video problem CrossPoint switchers\⤀Optimizing the Audio Audio Models\⤀ General checksConfiguration Worksheets Worksheet example 1 System equipment3-60 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dFigure 3-85 - Worksheet example 2 Daily configuration Worksheet example 2 Daily configurationCrossPoint / MAV Matrix Switchers Operation Worksheet example 3 Test configuration Figure 3-86 - Worksheet example 3 Test configuration3-62 CrossPoint / MAV Matrix Switchers Operation Operation, cont’d32-button switchers configuration worksheet CrossPoint / MAV Matrix Switchers OperationPreset # Input sources3-64 CrossPoint / MAV Matrix Switchers Operation Operation, cont’d16-button switchers configuration worksheet CrossPoint / MAV Matrix Switchers OperationPreset # Input sources3-66 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dSerial Ports Ethernet LAN\⤀ Port Host-to-Switcher Instructions Switcher-Initiated Messages Switcher Error ResponsesUsing the Command/Response Tables Chapter4FourProgrammer’s Guide Serial PortsRear panel Remote port Figure 4-1 - Remote connector pin assignmentsCrossPoint / MAV Matrix Switchers Programmer’s Guide Front panel Configuration portFigure 4-2 - Optional 9-pin TRS RS-232 cable Programmer’s Guide, cont’d Ethernet LAN\⤀ PortEthernet connection Figure 4-3 - RJ-45 Ethernet connector pin assignmentsDefault IP addresses Connection TimeoutsEstablishing a connection Number of connectionsHost-to-Switcher Instructions Switcher-Initiated MessagesVerbose Mode 4-6 CrossPoint / MAV Matrix Switchers Programmer’s GuideSwitcher Error Responses CrossPoint / MAV Matrix Switchers Programmer’s Guide4-8 CrossPoint / MAV Matrix Switchers Programmer’s Guide Using the Command/Response TablesProgrammer’s Guide, cont’d Page 4-10 CrossPoint / MAV Matrix Switchers Programmer’s Guide Command/response table for SIS commandsProgrammer’s Guide, cont’d Command/response table for SIS commands continued\⤀ CommandASCII command CrossPoint / MAV Matrix Switchers Programmer’s GuideCommand/response table for SIS commands continued\⤀ CommandASCII command 4-12 CrossPoint / MAV Matrix Switchers Programmer’s GuideCommand/response table for SIS commands continued\⤀ CommandASCII command CrossPoint / MAV Matrix Switchers Programmer’s GuideCommand/response table for SIS commands continued\⤀ CommandASCII command 4-14 CrossPoint / MAV Matrix Switchers Programmer’s GuideView ties, gain, volume, mutes, presets, and DSVP Command/response table for SIS commands continued\⤀MAV Plus Command/response table for SIS commands continued\⤀ CommandASCII command 4-16 CrossPoint / MAV Matrix Switchers Programmer’s GuideX1# X1# Command/response table for SIS commands continued\⤀Command ASCII commandCommand/response table for SIS commands continued Programmer’s Guide, cont’dI/O Grouping continued NamesResets Command/response table for SIS commands continued\⤀Lock executive\⤀ modes Command/response table for SIS commands continued\⤀ CommandASCII command 4-20 CrossPoint / MAV Matrix Switchers Programmer’s GuideCommand/response table for SIS commands continued\⤀ CommandASCII command CrossPoint / MAV Matrix Switchers Programmer’s GuideSymbol definitions Command/Response Table for IP-specific SIS CommandsProgrammer’s Guide, cont’d CrossPoint / MAV Matrix Switchers Programmer’s Guide X5 X5 X5IP setup commands Command/response table for IP-specific SIS commandsProgrammer’s Guide, cont’d Command/response table for IP-specific SIS commands continued\⤀ IP setup commands continued\⤀4-26 CrossPoint / MAV Matrix Switchers Programmer’s Guide Special CharactersProgrammer’s Guide, cont’d Matrix Switchers Control Program Special Characters Chapter5FiveMatrix Software Button Label Generator ProgramMatrix Switchers Control Program Installing the softwareMatrix Software The Matrix Switchers Control Program The Firmware LoaderEthernet protocol settings Software operation via EthernetCrossPoint / MAV Matrix Switchers Matrix Software Using the Matrix Switcher Control software Matrix Software, cont’dFigure 5-4 - Address and password entry 5-4 CrossPoint / MAV Matrix Switchers Matrix SoftwareCrossPoint / MAV Matrix Switchers Matrix Software Figure 5-5 - Extron Matrix Switchers Control Program window blankIf the IP address is correct Proceed to step 3b Matrix Software, cont’d 5-6 CrossPoint / MAV Matrix Switchers Matrix SoftwareFigure 5-6 - Sample program window complete IP Settings/Options window Figure 5-7 - Control program IP setting/options windowCrossPoint / MAV Matrix Switchers Matrix Software Matrix IP Address field5-8 CrossPoint / MAV Matrix Switchers Matrix Software Matrix Software, cont’dEdit the address as desired Address fieldCrossPoint / MAV Matrix Switchers Matrix Software Subnet Mask fieldEdit the mask as desired Mask fieldAdministrator Password field 5-10 CrossPoint / MAV Matrix Switchers Matrix SoftwareMatrix Software, cont’d Sync Time to PC buttonUser Password field CrossPoint / MAV Matrix Switchers Matrix SoftwareMail Server IP Address field cursor5-12 CrossPoint / MAV Matrix Switchers Matrix Software Matrix Software, cont’dMiles Standish E-mail Addressee fieldsFigure 5-9 - Location of firmware upgrade files Updating firmwareCrossPoint / MAV Matrix Switchers Matrix Software Figure 5-10 - Downloading firmware upgrade files folder identified in the InstallShield Wizard window5-14 CrossPoint / MAV Matrix Switchers Matrix Software Folder where firmware is installedswitcher LAN port. See chapter 2, “Installation”, for more details Start the Matrix Switchers Control Program and connect to theClick Tools Update Firmware CrossPoint / MAV Matrix Switchers Matrix Software5-16 CrossPoint / MAV Matrix Switchers Matrix Software Matrix Software, cont’dSerial-port-connected firmware upload Figure 5-12 - Firmware loadingFront panel Configuration port, enter CrossPoint / MAV Matrix Switchers Matrix SoftwareFigure 5-13 - Confirm window 13. If necessary, change the port number in the device port fieldUploading HTML files 5-18 CrossPoint / MAV Matrix Switchers Matrix SoftwareMatrix Software, cont’d Figure 5-14 - HTML Files List windowWindows buttons, drop boxes, and trashcan Windows menusExit - Closes the Matrix Switchers Control Program CrossPoint / MAV Matrix Switchers Matrix SoftwareMatrix Software, cont’d 5-20 CrossPoint / MAV Matrix Switchers Matrix SoftwareTools menu Audio-input Configuration selection CrossPoint / MAV Matrix Switchers Matrix SoftwareWhite - Not displayed for the CrossPoint or MAV Figure 5-15 - Status window5-22 CrossPoint / MAV Matrix Switchers Matrix Software Matrix Software, cont’dPreferences menu Figure 5-16 - Ties shown as linesUsing Emulation mode Using the help systemMaster-Reset selection Switcher + Control PgmButton-Label Generator Program 5-24 CrossPoint / MAV Matrix Switchers Matrix SoftwareMatrix Software, cont’d Special CharactersCrossPoint / MAV Matrix Switchers Matrix Software Using the Button-Label Generator softwareFigure 5-19 - Extron’s Button-Label Generator window 5-26 CrossPoint / MAV Matrix Switchers Matrix Software Matrix Software, cont’dDownload the Startup Page Status Tab Configuration Tab Chapter6SixHTML Operation File Management Tab Control Tab Special CharactersHTML Operation Download the Startup Page6-2 CrossPoint / MAV Matrix Switchers HTML Operation Start the Web browser programStatus Tab System Status pageCrossPoint / MAV Matrix Switchers HTML Operation Figure 6-2 - System Status pageDSVP page CrossPoint switchers\⤀ HTML Operation, cont’d6-4 CrossPoint / MAV Matrix Switchers HTML Operation Figure 6-3 - DSVP pageConfiguration Tab System Settings PageFigure 6-4 - System Settings page CrossPoint / MAV Matrix Switchers HTML OperationIP Settings fields 6-6 CrossPoint / MAV Matrix Switchers HTML OperationHTML Operation, cont’d Unit Name fieldDate/Time Settings fields Figure 6-5 - Date/Time Settings fieldsCrossPoint / MAV Matrix Switchers HTML Operation year, hours, minutes, AM/PM, and time zone. A drop-down scroll boxPasswords page Figure 6-6 - Passwords page6-8 CrossPoint / MAV Matrix Switchers HTML Operation HTML Operation, cont’dEmail Settings page Figure 6-7 - Email Settings pageCrossPoint / MAV Matrix Switchers HTML Operation Mail IP Address fieldFirmware Upgrade page Figure 6-8 - Firmware Upgrade page6-10 CrossPoint / MAV Matrix Switchers HTML Operation HTML Operation, cont’dFile Management Tab File Management PageClick the Firmware Upgrade link CrossPoint / MAV Matrix Switchers HTML OperationControl Tab User Control Page6-12 CrossPoint / MAV Matrix Switchers HTML Operation HTML Operation, cont’dRGB and Audio Settings page Figure 6-11 - RGB and Audio Settings pageCrossPoint / MAV Matrix Switchers HTML Operation Creating or deleting a tie6-14 CrossPoint / MAV Matrix Switchers HTML Operation HTML Operation, cont’dChange the input gain and attenuation audio models\⤀ Figure 6-12 - Input selection drop boxCrossPoint / MAV Matrix Switchers HTML Operation Mute and unmute one or all outputsMute one or all outputs as follows Figure 6-14 - Output selection drop boxChange the RGB delay CrossPoint switchers\⤀ Figure 6-17 - RGB delay drop box6-16 CrossPoint / MAV Matrix Switchers HTML Operation HTML Operation, cont’dChange the output volume level audio models\⤀ Figure 6-19 - Volume drop boxCrossPoint / MAV Matrix Switchers HTML Operation Figure 6-18 - Output selection drop box6-18 CrossPoint / MAV Matrix Switchers HTML Operation Audio volume adjustment settingsHTML Operation, cont’d Global Presets page Figure 6-20 - Global Presets pageSaving a preset Save the current configuration configuration 0 as a preset as followsRecalling a preset 6-20 CrossPoint / MAV Matrix Switchers HTML OperationHTML Operation, cont’d Special CharactersAAppendix A Ethernet ConnectionEthernet Link Subnetting - A Primer CrossPoint / MAV Matrix SwitchersDefault address Ethernet ConnectionEthernet Link Figure A-1 - RJ-45 connector pinout tablesConnecting as a Telnet client CrossPoint / MAV Matrix Switchers Ethernet ConnectionPinging to determine Extron IP address Figure A-2 - Ping responseEthernet Connection, cont’d A-4 CrossPoint / MAV Matrix Switchers Ethernet ConnectionFigure A-3 - Telnet screen Telnet tipsCrossPoint / MAV Matrix Switchers Ethernet Connection Local echoSet carriage return-line feed CloseSubnetting - A Primer GatewaysLocal and remote devices IP addresses and octetsDetermining whether devices are on the same subnet CrossPoint / MAV Matrix Switchers Ethernet ConnectionUnmasked octets are compared indicated by ? in figure A-6 Masked octets are not compared indicated by X in figure A-6A-8 CrossPoint / MAV Matrix Switchers Ethernet Connection Ethernet Connection, cont’dCrossPoint 450 Plus Specifications CrossPoint Ultra Specifications MAV Plus Specifications Part Numbers and Accessories Button LabelsAppendixBB Reference InformationCrossPoint 450 Plus Specifications Reference InformationVideo Video inputSync Audio - audio models onlyAudio input - audio models only Audio output - audio models onlyControl/remote - switcher Reference Information, cont’dGeneral B-4 CrossPoint / MAV Matrix Switchers Reference InformationCrossPoint Ultra Specifications CrossPoint / MAV Matrix Switchers Reference InformationVideo Video inputAudio- audio models only B-6 CrossPoint / MAV Matrix Switchers Reference InformationReference Information, cont’d Video outputAudio input- audio models only Audio output- audio models onlyControl/remote - switcher CrossPoint / MAV Matrix Switchers Reference InformationB-8 CrossPoint / MAV Matrix Switchers Reference Information Reference Information, cont’dGeneral N All nominal levels are at ±10%MAV Plus Specifications Video - video modelsVideo input - video models CrossPoint / MAV Matrix Switchers Reference InformationVideo output - video models Sync - MAV Plus 88/128/1212/168/816/1616 video modelsSync - MAV Plus 2412/2424/3216/3232 video models B-10 CrossPoint / MAV Matrix Switchers Reference InformationAudio input - audio models Audio - audio modelsCrossPoint / MAV Matrix Switchers Reference Information B-11 Audio output - audio models Control/remote - switcherB-12 CrossPoint / MAV Matrix Switchers Reference Information Reference Information, cont’dCrossPoint / MAV Matrix Switchers Reference Information B-13 N All nominal levels are at ±10%2412 Series 3216 SeriesPart Numbers and Accessories CrossPoint 450 Plus matrix switcher part numbersCrossPoint Ultra matrix switcher part numbers Matrix switcher part numbersMAV Plus matrix switcher part numbers MAV Plus matrix switcher part numbersCrossPoint / MAV Matrix Switchers Reference Information B-15 Part numberMAV Plus matrix switcher part numbers B-16 CrossPoint / MAV Matrix Switchers Reference InformationReference Information, cont’d Part numberReplacement parts Optional accessoriesIncluded parts AccessoryCables AccessoryRG6/super high resolution cable RG59/high resolution cablePre-cut cables Plenum BNC-5 mini high resolution cableAssorted connectors RG59/high resolution cableInstalling labels in the matrix switcher’s buttons Button LabelsFigure B-1 - Illuminated button label replacement B-20 CrossPoint / MAV Matrix Switchers Reference InformationCrossPoint / MAV Matrix Switchers Reference Information B-21 Button label blanks, 16-button stripsB-22 CrossPoint / MAV Matrix Switchers Reference Information Reference Information, cont’dExtron’s Warranty USA, Canada, South AmericaEurope, Africa, and the Middle East and Central AmericaExtron Electronics, Europe Beeldschermweg 6C