Manuals / Extron electronic / Computer Equipment / Switch

Extron electronic Ultra Series manual 19 - Captive screw connector wiring for audio output

Models: Ultra Series MAV Plus Series

1 214

Download 214 pages 8.93 Kb

Page 37

Connections for balanced and unbalanced audio outputs — These 3.5 mm,

E	Connections for balanced and unbalanced audio outputs — These 3.5 mm,
	5-pole captive screw connectors output the selected unamplified, line level
	audio. Connect audio devices, such as an audio amplifier or powered
	speakers. See figure 2-19 to properly wire an output connector. Use
	the supplied tie-wrap to strap the audio cable to the extended tail of the
	connector.

Tip

NO GROUND HERE.

Sleeve(s)

Tip

NO GROUND HERE.

Do not tin the wires!

Unbalanced Stereo Output

	Tip	L
	Ring	L
	Ring
	Sleeve(s)
	Tip	R
	Ring	R
	Ring

Balanced Stereo Output

Figure 2-19 — Captive screw connector wiring for audio output

CConnect the sleeve to ground (Gnd). Connecting the sleeve to a negative (-) terminal will damage the audio output circuits.

CThe length of the exposed (stripped) portion of the copper wires is important. The ideal length is 3/16” (5 mm). Longer bare wires can short together. Shorter bare wires are not as secure in the direct insertion connectors and could be pulled out.

The volume level for each output can be individually set via the front panel or Ethernet or serial port control. See chapter 3, “Operation”, chapter 4, “Programmer’s Guide”, chapter 5, “Matrix Software”, and chapter 6, “HTML Operation” for details.

RCA connector model (MAV Plus 128 AV RCA\⤀

F	Connections for unbalanced audio inputs — Each input has a pair (left and
	right) of female RCA connectors for unbalanced stereo audio input.
G	Connections for unbalanced audio outputs — Each output has a pair (left
	and right) of female RCA connectors for unbalanced stereo audio output.

CrossPoint / MAV Matrix Switchers • Installation 2-15

Image 37

Extron electronic Ultra Series, MAV Plus Series manual Connections for balanced and unbalanced audio outputs - These 3.5 mm

Contents

CrossPoint 450 Plus Series CrossPoint Ultra Series MAV Plus Series Matrix Switchers68-521-20 Rev. A Safety Instructions English PrecautionsConsignes de Sécurité Français Sicherheitsanleitungen DeutschFCC Class A Notice Page Front Panel Configuration PortMatrix Sizes up to 1616 Only Table of ContentsCrossPoint / MAV Matrix Switchers Table of Contents Viewing and adjusting the input audio level audio models Table of Contents, cont’dViewing and adjusting the output volume audio models Plasma display S-video problem CrossPoint switchersCrossPoint / MAV Matrix Switchers Table of Contents Command/Response Table for IP-specific SIS Commandsiv CrossPoint / MAV Matrix Switchers Table of Contents Table of Contents, cont’dCrossPoint / MAV Matrix Switchers Table of Contents vi CrossPoint / MAV Matrix Switchers Table of Contents Table of Contents, cont’d68-521-20 A About this Manual About the CrossPoint / MAV Matrix Switchers CrossPoint / MAV Matrix SwitchersDefinitions Features Chapter1OneIntroduction About the Matrix SwitchersAbout this Manual 1-2 CrossPoint / MAV Matrix Switchers IntroductionExtron CrossPoint Ultra 128 HVA Matrix SwitcherFigure 1-1 - Typical CrossPoint Ultra matrix switcher application CrossPoint / MAV Matrix Switchers IntroductionExtron MAV Plus 1616 HDA Introduction, cont’d16 Outputs 16 InputsCrossPoint / MAV Matrix Switchers Introduction CrossPoint Ultra switchersMAV Plus switchers CrossPoint 450 Plus switchers1-6 CrossPoint / MAV Matrix Switchers Introduction Introduction, cont’dCrossPoint / MAV Matrix Switchers Introduction The MAV Plus Series switchers have a bandwidth of 150 MHz -3 dBMAV 1212 Plus 12 inputs by 12 outputs MAV 1616 Plus 16 inputs by 16 outputsDefinitions FeaturesConfiguration - One or more ties or one or more sets of ties 1-8 CrossPoint / MAV Matrix Switchers IntroductionDigital Sync Validation Processing DSVP CrossPoint CrossPoint / MAV Matrix Switchers IntroductionInput # Figure 1-3 - DSVP data displayIntroduction, cont’d 1-10 CrossPoint / MAV Matrix Switchers IntroductionSIS for easy programming and operation Power supply status LEDs Primary and redundant power suppliesCrossPoint / MAV Matrix Switchers Introduction Introduction, cont’d 1-12 CrossPoint / MAV Matrix Switchers IntroductionMounting the Switcher Rear Panel Views Rear Panel Connections InstallationFront Panel Configuration Port Chapter2TwoMounting the Switcher InstallationUL guidelines 2-2 CrossPoint / MAV Matrix Switchers Installation2. Secure the switcher to the rack using the supplied bolts Mounting instructionsFigure 2-1 - Installing the switcher in a rack CrossPoint / MAV Matrix Switchers InstallationRear Panel Views Installation, cont’dCrossPoint 450 Plus switchers Figure 2-2 - CrossPoint 450 Plus 3232 HVA matrix switcherFigure 2-3 - CrossPoint Ultra 1616 HVA matrix switcher CrossPoint Ultra switchersswitcher Figure 2-4 - CrossPoint Ultra 128 HVA matrix switcherMAV Plus switchers Installation, cont’dFigure 2-5 - MAV Plus 3232 SVA matrix switcher Figure 2-6 - MAV Plus 3232 matrix switchers with various formatsFigure 2-8 - MAV Plus 1616 matrix switchers with various formats Figure 2-7 - MAV Plus 1616 HDA matrix switcherCrossPoint / MAV Matrix Switchers Installation RESETFigure 2-9 - MAV Plus 128 AV RCA matrix switcher Installation, cont’dFigure 2-10 - MAV Plus 128 HDA matrix switcher Figure 2-11 - MAV Plus 128 matrix switchers with various formatsRear Panel Connections Video input and output video switchers\⤀RGBHV CrossPoint switchers\⤀ CrossPoint / MAV Matrix Switchers Installation2-10 CrossPoint / MAV Matrix Switchers Installation Installation, cont’dCrossPoint 450 Plus 2412, 2424, 3216 CrossPoint UltraCrossPoint / MAV Matrix Switchers Installation Video MAV Plus switchers\⤀Video inputs - Connect component/HDTV video figure Video outputs - Connect component/HDTV video figure2-12 CrossPoint / MAV Matrix Switchers Installation Installation, cont’dFigure 2-14 - MAV Plus S-video connections Figure 2-15 - MAV Plus video connectionsSync termination switches - The RGB CrossPoint matrix switchers have Sync termination switches CrossPoint\⤀Figure 2-16 - Sync termination switches CrossPoint / MAV Matrix Switchers InstallationInstallation, cont’d Audio input and output audio models\⤀Captive screw connector models all except MAV Plus 128 AV RCA\⤀ Figure 2-17 - Captive screw connector wiring for audio inputsRCA connector model MAV Plus 128 AV RCA\⤀ Figure 2-19 - Captive screw connector wiring for audio outputCrossPoint / MAV Matrix Switchers Installation Connections for balanced and unbalanced audio outputs - These 3.5 mmEthernet RS-232/RS-422Installation, cont’d D connector for serial RS-232/RS-422 control figureFigure 2-21 - RJ-45 connector and pinout tables Cabling and RJ-45 connector wiringCrossPoint / MAV Matrix Switchers Installation 10Base-T Ethernet requires CAT 3 UTP or STP cable at minimum2-18 CrossPoint / MAV Matrix Switchers Installation Reset buttonN Hard reset does not clear the current configuration Matrix SwitcherCrossPoint / MAV Matrix Switchers Installation PowerFigure 2-23 - Multiple device external sync connection example Installation, cont’d Front Panel Configuration Port Matrix Sizes up to 1616 Only\⤀Figure 2-24 - Front panel configuration port 2-20 CrossPoint / MAV Matrix Switchers InstallationCrossPoint / MAV Matrix Switchers Installation This port is RS-232 only, with its default protocols as follows9600 baud no parity2-22 CrossPoint / MAV Matrix Switchers Installation Installation, cont’dTroubleshooting Configuration Worksheets Front Panel Controls and Indicators Front Panel OperationsChapter3Three OperationOperation Front Panel Controls and Indicators3-2 CrossPoint / MAV Matrix Switchers Operation Figure 3-1 - Front panel, CrossPoint Ultra 128 HVAF G H A B C D EPower Supply LEDs - See page CrossPoint / MAV Matrix Switchers OperationInput and output buttons Operation, cont’d3-4 CrossPoint / MAV Matrix Switchers Operation Lit A preset has already been saved to this locationCrossPoint / MAV Matrix Switchers Operation CrossPoint switchers, Input 1 through 10 Display the RGB delay. SeeSave configuration or preset changes that you make on the front panel Control buttons3-6 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dCrossPoint / MAV Matrix Switchers Operation Preset button - The Preset button has two primary functions and three3-8 CrossPoint / MAV Matrix Switchers Operation I/O controlsOperation, cont’d Primary functionsCrossPoint / MAV Matrix Switchers Operation CrossPoint switchers Selects the RGB delay mode, in which you canset the RGB delay. See “Setting RGB delay CrossPoint Switchers” on With the RGBHV/Video button, commands the front panel system resetButton icons Power indicators 2412 and larger models only\⤀I Primary and Redundant Power Supply LEDs 3-10 CrossPoint / MAV Matrix Switchers OperationDefinitions Front Panel OperationsConfiguration - One or more ties or one or more sets of ties CrossPoint / MAV Matrix Switchers OperationPower Front panel security lockouts3-12 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dSelect to configure video, audio, or both by pressing the RGBHV Creating a configurationCrossPoint switchers or Video MAV Plus switchers button and/or Audio CrossPoint / MAV Matrix Switchers Operation3-14 CrossPoint / MAV Matrix Switchers Operation 1 2 3 4 5 6 7 8 15 16 17 18 19 20 21 22 23 24 31Operation, cont’d Example 1 Creating a set of video and audio tiesFigure 3-10 - Example 1, final configuration The current configuration figure 3-10 is nowCrossPoint / MAV Matrix Switchers Operation ENTER PRESET VIEW3-16 CrossPoint / MAV Matrix Switchers Operation 1 2 3 4 5 6 7 8Operation, cont’d 1 2 3 4 5 6 7 8Figure 3-16 - Example 2, final configuration The current configuration figure 3-16 is nowCrossPoint / MAV Matrix Switchers Operation 4. Press and release the output 1 button figureOperation, cont’d 3-18 CrossPoint / MAV Matrix Switchers Operation1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8CrossPoint / MAV Matrix Switchers Operation Figure 3-22 - Example 3, final configuration, audio switcher4. Press and release the output 4 button figure Figure 3-20 - Deselect the output3-20 CrossPoint / MAV Matrix Switchers Operation Viewing a configurationOperation, cont’d CrossPoint / MAV Matrix Switchers Operation 1 2 3 4 5 6 7 8 15Example 4 Viewing video and audio, audio only, and video only ties Figure 3-23 - Clear all selectionsOperation, cont’d 3-22 CrossPoint / MAV Matrix Switchers Operation1 2 3 4 5 6 7 1 2 3 4 5 6 7 81 2 3 4 5 6 7 8 CrossPoint / MAV Matrix Switchers Operation7. Press and release the View button to exit View-only mode figure Figure 3-28 - Press the View button to exit View-only mode3-24 CrossPoint / MAV Matrix Switchers Operation I/O groupingOperation, cont’d 1 2 3 4 5 6 7 8 9CrossPoint / MAV Matrix Switchers Operation Press the Preset button to select group3. Press and release one of the Control buttons to select a group Press the Enter button to select groupOperation, cont’d 3-26 CrossPoint / MAV Matrix Switchers OperationExample 5 Grouping inputs and outputs Figure 3-30 - Clear all selections1 2 3 4 5 6 7 8 15 CrossPoint / MAV Matrix Switchers Operation1 2 3 4 5 6 7 8 15 1 2 3 4 5 6 7 83-28 CrossPoint / MAV Matrix Switchers Operation Setting RGB delay CrossPoint switchers\⤀Operation, cont’d Figure 3-36 - Deselect I/O Group modeExample 6 Setting the RGB delay for an output 22 23 24CrossPoint / MAV Matrix Switchers Operation Figure 3-37 - Clear all selections3-30 CrossPoint / MAV Matrix Switchers Operation Figure 3-40 - Adjust the RGB delay intervalOperation, cont’d Figure 3-41 - Deselect RGB Delay mode10 11 12 13 14 15 Using presets17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Figure 3-42 - Preset locations by matrix sizeFigure 3-44 - Enter Save Preset mode Example 7 Saving a presetFigure 3-45 - Select the preset 3-32 CrossPoint / MAV Matrix Switchers OperationFigure 3-48 - Enter Recall Preset mode Example 8 Recalling a presetCrossPoint / MAV Matrix Switchers Operation Figure 3-46 - Press the Enter buttonFigure 3-49 - Select the preset 1 2 3 4 153-34 CrossPoint / MAV Matrix Switchers Operation recall the presetCrossPoint / MAV Matrix Switchers Operation Muting and unmuting video and/or audio outputsIndividual outputs can be muted or unmuted as follows Press and release the View buttonOperation, cont’d 3-36 CrossPoint / MAV Matrix Switchers Operation1 2 3 4 5 6 7 8 15 Example 9 Muting and unmuting an audio/RS-232 outputFigure 3-53 - Mute the outputs CrossPoint / MAV Matrix Switchers OperationFigure 3-54 - Unmute the outputs 6. Press and release the View button to exit View-only mode figure3-38 CrossPoint / MAV Matrix Switchers Operation Viewing and adjusting the input audio level audio models\⤀Operation, cont’d Figure 3-56 - Audio gain and attenuationCrossPoint / MAV Matrix Switchers Operation Example 10 Viewing and adjusting an input audio levelFigure 3-57 - Clear all selections Figure 3-58 - Select Audio mode3-40 CrossPoint / MAV Matrix Switchers Operation Input audio level adjustment displaysOperation, cont’d CrossPoint 450 PlusCrossPoint / MAV Matrix Switchers Operation Input audio level adjustment displays= Unlit button = Blinking buttonFigure 3-61 - Level display on a 8-output-button switcher Figure 3-60 - Level display on a 16-output-button switcher3-42 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dFigure 3-63 - Level display on a 16-output-button switcher Figure 3-62 - Adjust the input audio levelFigure 3-64 - Level display on a 8-output-button switcher CrossPoint / MAV Matrix Switchers Operation3-44 CrossPoint / MAV Matrix Switchers Operation Viewing and adjusting the output volume audio models\⤀Operation, cont’d Figure 3-65 - Deselect Audio modePush Esc button again - 5.5% + 1.5% = 7% volume Reading the displayed volumePush Esc button twice more - 7% + 1.5% + 1.5% = 10% volume Push Esc button nineteen times more - 10% + 191.5% = 38.5% volume3-46 CrossPoint / MAV Matrix Switchers Operation Audio volume adjustment settingsOperation, cont’d 63 dB of attenuation is applied to the output CrossPoint / MAV Matrix Switchers Operation3-48 CrossPoint / MAV Matrix Switchers Operation Example 11 Viewing and adjusting an output volume levelPRESET Operation, cont’d10 11 10 1113 14 15 Figure 3-69 - Volume display on a 16-input-button switcherFigure 3-72 - Volume display on a 16-input-button switcher Figure 3-71 - Adjust the output audio volume3-50 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dFast Blinking Button 26 dB attenuation 61% volume CrossPoint / MAV Matrix Switchers Operation10 11 5. Press and release the Audio button figure3-52 CrossPoint / MAV Matrix Switchers Operation Setting the front panel locks Executive modes\⤀Operation, cont’d Selecting Lock mode 2 or toggling between mode 2 and modeFigure 3-77 - System reset Performing a system reset from the front panelCrossPoint / MAV Matrix Switchers Operation Selecting Lock mode 2 or toggling between mode 2 and modeSelecting the rear panel Remote port protocol and baud rate Background illumination3-54 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dSee the following table for a summary of the modes Rear Panel Operations3-56 CrossPoint / MAV Matrix Switchers Operation Reset Mode Comparison/SummaryThe switcher reverts to the factory default Mode 3 turns events on or off. During resettingPerform a soft reset of the switcher as follows Performing soft system resets resets 3, 4, and 5\⤀Figure 3-82 - Whole switcher and absolute resets CrossPoint / MAV Matrix Switchers OperationFigure 3-83 - Hard reset Performing a hard reset3-58 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dPlasma display S-video problem CrossPoint switchers\⤀ TroubleshootingOptimizing the Audio Audio Models\⤀ General checksWorksheet example 1 System equipment Configuration Worksheets3-60 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dFigure 3-85 - Worksheet example 2 Daily configuration Worksheet example 2 Daily configurationCrossPoint / MAV Matrix Switchers Operation Figure 3-86 - Worksheet example 3 Test configuration Worksheet example 3 Test configuration3-62 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dCrossPoint / MAV Matrix Switchers Operation 32-button switchers configuration worksheetPreset # Input sourcesOperation, cont’d 3-64 CrossPoint / MAV Matrix Switchers OperationCrossPoint / MAV Matrix Switchers Operation 16-button switchers configuration worksheetPreset # Input sourcesOperation, cont’d 3-66 CrossPoint / MAV Matrix Switchers OperationSwitcher-Initiated Messages Switcher Error Responses Serial Ports Ethernet LAN\⤀ Port Host-to-Switcher InstructionsUsing the Command/Response Tables Chapter4FourSerial Ports Programmer’s GuideRear panel Remote port Figure 4-1 - Remote connector pin assignmentsCrossPoint / MAV Matrix Switchers Programmer’s Guide Front panel Configuration portFigure 4-2 - Optional 9-pin TRS RS-232 cable Ethernet LAN\⤀ Port Programmer’s Guide, cont’dEthernet connection Figure 4-3 - RJ-45 Ethernet connector pin assignmentsConnection Timeouts Default IP addressesEstablishing a connection Number of connectionsSwitcher-Initiated Messages Host-to-Switcher InstructionsVerbose Mode 4-6 CrossPoint / MAV Matrix Switchers Programmer’s GuideCrossPoint / MAV Matrix Switchers Programmer’s Guide Switcher Error Responses4-8 CrossPoint / MAV Matrix Switchers Programmer’s Guide Using the Command/Response TablesProgrammer’s Guide, cont’d Page 4-10 CrossPoint / MAV Matrix Switchers Programmer’s Guide Command/response table for SIS commandsProgrammer’s Guide, cont’d Command Command/response table for SIS commands continued\⤀ASCII command CrossPoint / MAV Matrix Switchers Programmer’s GuideCommand Command/response table for SIS commands continued\⤀ASCII command 4-12 CrossPoint / MAV Matrix Switchers Programmer’s GuideCommand Command/response table for SIS commands continued\⤀ASCII command CrossPoint / MAV Matrix Switchers Programmer’s GuideCommand Command/response table for SIS commands continued\⤀ASCII command 4-14 CrossPoint / MAV Matrix Switchers Programmer’s GuideView ties, gain, volume, mutes, presets, and DSVP Command/response table for SIS commands continued\⤀MAV Plus Command Command/response table for SIS commands continued\⤀ASCII command 4-16 CrossPoint / MAV Matrix Switchers Programmer’s GuideCommand/response table for SIS commands continued\⤀ X1# X1#Command ASCII commandProgrammer’s Guide, cont’d Command/response table for SIS commands continuedI/O Grouping continued NamesResets Command/response table for SIS commands continued\⤀Lock executive\⤀ modes Command Command/response table for SIS commands continued\⤀ASCII command 4-20 CrossPoint / MAV Matrix Switchers Programmer’s GuideCommand Command/response table for SIS commands continued\⤀ASCII command CrossPoint / MAV Matrix Switchers Programmer’s GuideSymbol definitions Command/Response Table for IP-specific SIS CommandsProgrammer’s Guide, cont’d X5 X5 X5 CrossPoint / MAV Matrix Switchers Programmer’s GuideIP setup commands Command/response table for IP-specific SIS commandsProgrammer’s Guide, cont’d IP setup commands continued\⤀ Command/response table for IP-specific SIS commands continued\⤀4-26 CrossPoint / MAV Matrix Switchers Programmer’s Guide Special CharactersProgrammer’s Guide, cont’d Chapter5Five Matrix Switchers Control Program Special CharactersMatrix Software Button Label Generator ProgramInstalling the software Matrix Switchers Control ProgramMatrix Software The Matrix Switchers Control Program The Firmware LoaderEthernet protocol settings Software operation via EthernetCrossPoint / MAV Matrix Switchers Matrix Software Matrix Software, cont’d Using the Matrix Switcher Control softwareFigure 5-4 - Address and password entry 5-4 CrossPoint / MAV Matrix Switchers Matrix SoftwareCrossPoint / MAV Matrix Switchers Matrix Software Figure 5-5 - Extron Matrix Switchers Control Program window blankIf the IP address is correct Proceed to step 3b Matrix Software, cont’d 5-6 CrossPoint / MAV Matrix Switchers Matrix SoftwareFigure 5-6 - Sample program window complete Figure 5-7 - Control program IP setting/options window IP Settings/Options windowCrossPoint / MAV Matrix Switchers Matrix Software Matrix IP Address fieldMatrix Software, cont’d 5-8 CrossPoint / MAV Matrix Switchers Matrix SoftwareEdit the address as desired Address fieldSubnet Mask field CrossPoint / MAV Matrix Switchers Matrix SoftwareEdit the mask as desired Mask field5-10 CrossPoint / MAV Matrix Switchers Matrix Software Administrator Password fieldMatrix Software, cont’d Sync Time to PC buttonCrossPoint / MAV Matrix Switchers Matrix Software User Password fieldMail Server IP Address field cursorMatrix Software, cont’d 5-12 CrossPoint / MAV Matrix Switchers Matrix SoftwareMiles Standish E-mail Addressee fieldsFigure 5-9 - Location of firmware upgrade files Updating firmwareCrossPoint / MAV Matrix Switchers Matrix Software folder identified in the InstallShield Wizard window Figure 5-10 - Downloading firmware upgrade files5-14 CrossPoint / MAV Matrix Switchers Matrix Software Folder where firmware is installedStart the Matrix Switchers Control Program and connect to the switcher LAN port. See chapter 2, “Installation”, for more detailsClick Tools Update Firmware CrossPoint / MAV Matrix Switchers Matrix SoftwareMatrix Software, cont’d 5-16 CrossPoint / MAV Matrix Switchers Matrix SoftwareSerial-port-connected firmware upload Figure 5-12 - Firmware loadingCrossPoint / MAV Matrix Switchers Matrix Software Front panel Configuration port, enterFigure 5-13 - Confirm window 13. If necessary, change the port number in the device port field5-18 CrossPoint / MAV Matrix Switchers Matrix Software Uploading HTML filesMatrix Software, cont’d Figure 5-14 - HTML Files List windowWindows menus Windows buttons, drop boxes, and trashcanExit - Closes the Matrix Switchers Control Program CrossPoint / MAV Matrix Switchers Matrix SoftwareMatrix Software, cont’d 5-20 CrossPoint / MAV Matrix Switchers Matrix SoftwareTools menu CrossPoint / MAV Matrix Switchers Matrix Software Audio-input Configuration selectionWhite - Not displayed for the CrossPoint or MAV Figure 5-15 - Status windowMatrix Software, cont’d 5-22 CrossPoint / MAV Matrix Switchers Matrix SoftwarePreferences menu Figure 5-16 - Ties shown as linesUsing the help system Using Emulation modeMaster-Reset selection Switcher + Control Pgm5-24 CrossPoint / MAV Matrix Switchers Matrix Software Button-Label Generator ProgramMatrix Software, cont’d Special CharactersCrossPoint / MAV Matrix Switchers Matrix Software Using the Button-Label Generator softwareFigure 5-19 - Extron’s Button-Label Generator window Matrix Software, cont’d 5-26 CrossPoint / MAV Matrix Switchers Matrix SoftwareChapter6Six Download the Startup Page Status Tab Configuration TabHTML Operation File Management Tab Control Tab Special CharactersDownload the Startup Page HTML Operation6-2 CrossPoint / MAV Matrix Switchers HTML Operation Start the Web browser programSystem Status page Status TabCrossPoint / MAV Matrix Switchers HTML Operation Figure 6-2 - System Status pageHTML Operation, cont’d DSVP page CrossPoint switchers\⤀6-4 CrossPoint / MAV Matrix Switchers HTML Operation Figure 6-3 - DSVP pageSystem Settings Page Configuration TabFigure 6-4 - System Settings page CrossPoint / MAV Matrix Switchers HTML Operation6-6 CrossPoint / MAV Matrix Switchers HTML Operation IP Settings fieldsHTML Operation, cont’d Unit Name fieldFigure 6-5 - Date/Time Settings fields Date/Time Settings fieldsCrossPoint / MAV Matrix Switchers HTML Operation year, hours, minutes, AM/PM, and time zone. A drop-down scroll boxFigure 6-6 - Passwords page Passwords page6-8 CrossPoint / MAV Matrix Switchers HTML Operation HTML Operation, cont’dFigure 6-7 - Email Settings page Email Settings pageCrossPoint / MAV Matrix Switchers HTML Operation Mail IP Address fieldFigure 6-8 - Firmware Upgrade page Firmware Upgrade page6-10 CrossPoint / MAV Matrix Switchers HTML Operation HTML Operation, cont’dFile Management Page File Management TabClick the Firmware Upgrade link CrossPoint / MAV Matrix Switchers HTML OperationUser Control Page Control Tab6-12 CrossPoint / MAV Matrix Switchers HTML Operation HTML Operation, cont’dFigure 6-11 - RGB and Audio Settings page RGB and Audio Settings pageCrossPoint / MAV Matrix Switchers HTML Operation Creating or deleting a tieHTML Operation, cont’d 6-14 CrossPoint / MAV Matrix Switchers HTML OperationChange the input gain and attenuation audio models\⤀ Figure 6-12 - Input selection drop boxMute and unmute one or all outputs CrossPoint / MAV Matrix Switchers HTML OperationMute one or all outputs as follows Figure 6-14 - Output selection drop box6-16 CrossPoint / MAV Matrix Switchers HTML Operation Change the RGB delay CrossPoint switchers\⤀HTML Operation, cont’d Figure 6-16 - Output selection drop boxFigure 6-19 - Volume drop box Change the output volume level audio models\⤀CrossPoint / MAV Matrix Switchers HTML Operation Figure 6-18 - Output selection drop box6-18 CrossPoint / MAV Matrix Switchers HTML Operation Audio volume adjustment settingsHTML Operation, cont’d Figure 6-20 - Global Presets page Global Presets pageSaving a preset Save the current configuration configuration 0 as a preset as follows6-20 CrossPoint / MAV Matrix Switchers HTML Operation Recalling a presetHTML Operation, cont’d Special CharactersEthernet Connection AAppendix AEthernet Link Subnetting - A Primer CrossPoint / MAV Matrix SwitchersEthernet Connection Default addressEthernet Link Figure A-1 - RJ-45 connector pinout tablesCrossPoint / MAV Matrix Switchers Ethernet Connection Connecting as a Telnet clientPinging to determine Extron IP address Figure A-2 - Ping responseA-4 CrossPoint / MAV Matrix Switchers Ethernet Connection Ethernet Connection, cont’dFigure A-3 - Telnet screen Telnet tipsLocal echo CrossPoint / MAV Matrix Switchers Ethernet ConnectionSet carriage return-line feed CloseGateways Subnetting - A PrimerLocal and remote devices IP addresses and octetsCrossPoint / MAV Matrix Switchers Ethernet Connection Determining whether devices are on the same subnetUnmasked octets are compared indicated by ? in figure A-6 Masked octets are not compared indicated by X in figure A-6Ethernet Connection, cont’d A-8 CrossPoint / MAV Matrix Switchers Ethernet ConnectionMAV Plus Specifications Part Numbers and Accessories Button Labels CrossPoint 450 Plus Specifications CrossPoint Ultra SpecificationsAppendixBB Reference InformationReference Information CrossPoint 450 Plus SpecificationsVideo Video inputAudio - audio models only SyncAudio input - audio models only Audio output - audio models onlyReference Information, cont’d Control/remote - switcherGeneral B-4 CrossPoint / MAV Matrix Switchers Reference InformationCrossPoint / MAV Matrix Switchers Reference Information CrossPoint Ultra SpecificationsVideo Video inputB-6 CrossPoint / MAV Matrix Switchers Reference Information Audio- audio models onlyReference Information, cont’d Video outputAudio output- audio models only Audio input- audio models onlyControl/remote - switcher CrossPoint / MAV Matrix Switchers Reference InformationReference Information, cont’d B-8 CrossPoint / MAV Matrix Switchers Reference InformationGeneral N All nominal levels are at ±10%Video - video models MAV Plus SpecificationsVideo input - video models CrossPoint / MAV Matrix Switchers Reference InformationSync - MAV Plus 88/128/1212/168/816/1616 video models Video output - video modelsSync - MAV Plus 2412/2424/3216/3232 video models B-10 CrossPoint / MAV Matrix Switchers Reference InformationAudio input - audio models Audio - audio modelsCrossPoint / MAV Matrix Switchers Reference Information B-11 Control/remote - switcher Audio output - audio modelsB-12 CrossPoint / MAV Matrix Switchers Reference Information Reference Information, cont’dN All nominal levels are at ±10% CrossPoint / MAV Matrix Switchers Reference Information B-132412 Series 3216 SeriesCrossPoint 450 Plus matrix switcher part numbers Part Numbers and AccessoriesCrossPoint Ultra matrix switcher part numbers Matrix switcher part numbersMAV Plus matrix switcher part numbers MAV Plus matrix switcher part numbersCrossPoint / MAV Matrix Switchers Reference Information B-15 Part numberB-16 CrossPoint / MAV Matrix Switchers Reference Information MAV Plus matrix switcher part numbersReference Information, cont’d Part numberOptional accessories Replacement partsIncluded parts AccessoryAccessory CablesRG6/super high resolution cable RG59/high resolution cablePlenum BNC-5 mini high resolution cable Pre-cut cablesAssorted connectors RG59/high resolution cableButton Labels Installing labels in the matrix switcher’s buttonsFigure B-1 - Illuminated button label replacement B-20 CrossPoint / MAV Matrix Switchers Reference InformationButton label blanks, 16-button strips CrossPoint / MAV Matrix Switchers Reference Information B-21Reference Information, cont’d B-22 CrossPoint / MAV Matrix Switchers Reference InformationUSA, Canada, South America Extron’s WarrantyEurope, Africa, and the Middle East and Central AmericaExtron Electronics, Europe Beeldschermweg 6C