Manuals / Extron electronic / Computer Equipment / Switch

Extron electronic Ultra Series, MAV Plus Series manual Cabling and RJ-45 connector wiring

Models: Ultra Series MAV Plus Series

1 214

Download 214 pages 8.93 Kb

Page 39

Cabling and RJ-45 connector wiring

Cabling and RJ-45 connector wiring

It is vital that your Ethernet cables be the correct cables, and that they be properly terminated with the correct pinout. Ethernet links use Category (CAT) 5e or CAT 6, unshielded twisted pair (UTP) or shielded twisted pair (STP) cables, terminated with RJ-45 connectors. Ethernet cables are limited to a length 328' (100 m).

NDo not use standard telephone cables. Telephone cables will not support Ethernet or Fast Ethernet.

Do not stretch or bend cables. Transmission errors can occur.

The cable used depends on your network speed. The switcher supports both 10 Mbps (10Base-T — Ethernet) and 100 Mbps (100Base-T — Fast Ethernet), half-duplex and full-duplex, Ethernet connections.

•10Base-T Ethernet requires CAT 3 UTP or STP cable at minimum.

•100Base-T Fast Ethernet requires CAT 5e UTP or STP cable at minimum.

The Ethernet cable can be terminated as a straight-through cable or a crossover cable and must be properly terminated for your application (figure 2-21).

•Crossover cable — Direct connection between the computer and the matrix switcher.

•Patch (straight) cable — Connection of the matrix switcher to an Ethernet LAN.

Patch (straight) cable

												Side 1			Side 2
											Pin	Wire color		Pin	Wire color
											1	White-orange		1	White-orange
Side
Side											2	Orange		2	Orange
										RJ-45	2	Orange		2	Orange

											3	White-green		3	White-green
										connector
										connector
											4	Blue		4	Blue
											4	Blue		4	Blue
											5	White-blue		5	White-blue



											6	Green		6	Green
											6	Green		6	Green

											7	White-brown		7	White-brown
											7	White-brown		7	White-brown

											8	Brown		8	Brown

Insert		Crossover cable
twisted		Side 1			Side 2
pair wires.		Side 1			Side 2
pair wires.	Pin	Wire color		Pin	Wire color
	Pin	Wire color		Pin	Wire color
	1	White-orange		1	White-green

	2	Orange		2	Green

	3	White-green		3	White-orange

	4	Blue		4	Blue

	5	White-blue		5	White-blue
	6	Green		6	Orange

	7	White-brown		7	White-brown

	8	Brown		8	Brown

Figure 2-21 — RJ-45 connector and pinout tables

CrossPoint / MAV Matrix Switchers • Installation 2-17

Image 39

Extron electronic Ultra Series, MAV Plus Series Cabling and RJ-45 connector wiring, 21 - RJ-45 connector and pinout tables

Contents

Matrix Switchers CrossPoint 450 Plus Series CrossPoint Ultra Series MAV Plus Series68-521-20 Rev. A Sicherheitsanleitungen Deutsch PrecautionsSafety Instructions English Consignes de Sécurité FrançaisFCC Class A Notice Page Table of Contents Front Panel Configuration PortMatrix Sizes up to 1616 OnlyCrossPoint / MAV Matrix Switchers Table of Contents Plasma display S-video problem CrossPoint switchers Table of Contents, cont’dViewing and adjusting the input audio level audio models Viewing and adjusting the output volume audio modelsCrossPoint / MAV Matrix Switchers Table of Contents Command/Response Table for IP-specific SIS Commandsiv CrossPoint / MAV Matrix Switchers Table of Contents Table of Contents, cont’dCrossPoint / MAV Matrix Switchers Table of Contents Table of Contents, cont’d vi CrossPoint / MAV Matrix Switchers Table of Contents68-521-20 A Chapter1One CrossPoint / MAV Matrix SwitchersAbout this Manual About the CrossPoint / MAV Matrix Switchers Definitions Features1-2 CrossPoint / MAV Matrix Switchers Introduction About the Matrix SwitchersIntroduction About this ManualCrossPoint / MAV Matrix Switchers Introduction Matrix SwitcherExtron CrossPoint Ultra 128 HVA Figure 1-1 - Typical CrossPoint Ultra matrix switcher application16 Inputs Introduction, cont’dExtron MAV Plus 1616 HDA 16 OutputsCrossPoint / MAV Matrix Switchers Introduction CrossPoint Ultra switchersIntroduction, cont’d CrossPoint 450 Plus switchersMAV Plus switchers 1-6 CrossPoint / MAV Matrix Switchers IntroductionMAV 1616 Plus 16 inputs by 16 outputs The MAV Plus Series switchers have a bandwidth of 150 MHz -3 dBCrossPoint / MAV Matrix Switchers Introduction MAV 1212 Plus 12 inputs by 12 outputs1-8 CrossPoint / MAV Matrix Switchers Introduction FeaturesDefinitions Configuration - One or more ties or one or more sets of tiesFigure 1-3 - DSVP data display CrossPoint / MAV Matrix Switchers IntroductionDigital Sync Validation Processing DSVP CrossPoint Input #1-10 CrossPoint / MAV Matrix Switchers Introduction Introduction, cont’dSIS for easy programming and operation Primary and redundant power supplies Power supply status LEDsCrossPoint / MAV Matrix Switchers Introduction Introduction, cont’d 1-12 CrossPoint / MAV Matrix Switchers IntroductionChapter2Two InstallationMounting the Switcher Rear Panel Views Rear Panel Connections Front Panel Configuration Port2-2 CrossPoint / MAV Matrix Switchers Installation InstallationMounting the Switcher UL guidelinesCrossPoint / MAV Matrix Switchers Installation Mounting instructions2. Secure the switcher to the rack using the supplied bolts Figure 2-1 - Installing the switcher in a rackFigure 2-2 - CrossPoint 450 Plus 3232 HVA matrix switcher Installation, cont’dRear Panel Views CrossPoint 450 Plus switchersFigure 2-4 - CrossPoint Ultra 128 HVA matrix switcher CrossPoint Ultra switchersFigure 2-3 - CrossPoint Ultra 1616 HVA matrix switcher switcherFigure 2-6 - MAV Plus 3232 matrix switchers with various formats Installation, cont’dMAV Plus switchers Figure 2-5 - MAV Plus 3232 SVA matrix switcherRESET Figure 2-7 - MAV Plus 1616 HDA matrix switcherFigure 2-8 - MAV Plus 1616 matrix switchers with various formats CrossPoint / MAV Matrix Switchers InstallationFigure 2-11 - MAV Plus 128 matrix switchers with various formats Installation, cont’dFigure 2-9 - MAV Plus 128 AV RCA matrix switcher Figure 2-10 - MAV Plus 128 HDA matrix switcherCrossPoint / MAV Matrix Switchers Installation Video input and output video switchers\⤀Rear Panel Connections RGBHV CrossPoint switchers\⤀CrossPoint Ultra Installation, cont’d2-10 CrossPoint / MAV Matrix Switchers Installation CrossPoint 450 Plus 2412, 2424, 3216Video outputs - Connect component/HDTV video figure Video MAV Plus switchers\⤀CrossPoint / MAV Matrix Switchers Installation Video inputs - Connect component/HDTV video figureFigure 2-15 - MAV Plus video connections Installation, cont’d2-12 CrossPoint / MAV Matrix Switchers Installation Figure 2-14 - MAV Plus S-video connectionsCrossPoint / MAV Matrix Switchers Installation Sync termination switches CrossPoint\⤀Sync termination switches - The RGB CrossPoint matrix switchers have Figure 2-16 - Sync termination switchesFigure 2-17 - Captive screw connector wiring for audio inputs Audio input and output audio models\⤀Installation, cont’d Captive screw connector models all except MAV Plus 128 AV RCA\⤀Connections for balanced and unbalanced audio outputs - These 3.5 mm Figure 2-19 - Captive screw connector wiring for audio outputRCA connector model MAV Plus 128 AV RCA\⤀ CrossPoint / MAV Matrix Switchers InstallationD connector for serial RS-232/RS-422 control figure RS-232/RS-422Ethernet Installation, cont’d10Base-T Ethernet requires CAT 3 UTP or STP cable at minimum Cabling and RJ-45 connector wiringFigure 2-21 - RJ-45 connector and pinout tables CrossPoint / MAV Matrix Switchers InstallationMatrix Switcher Reset button2-18 CrossPoint / MAV Matrix Switchers Installation N Hard reset does not clear the current configurationPower CrossPoint / MAV Matrix Switchers InstallationFigure 2-23 - Multiple device external sync connection example 2-20 CrossPoint / MAV Matrix Switchers Installation Front Panel Configuration Port Matrix Sizes up to 1616 Only\⤀Installation, cont’d Figure 2-24 - Front panel configuration portno parity This port is RS-232 only, with its default protocols as followsCrossPoint / MAV Matrix Switchers Installation 9600 baud2-22 CrossPoint / MAV Matrix Switchers Installation Installation, cont’dOperation Front Panel Controls and Indicators Front Panel OperationsTroubleshooting Configuration Worksheets Chapter3ThreeFigure 3-1 - Front panel, CrossPoint Ultra 128 HVA Front Panel Controls and IndicatorsOperation 3-2 CrossPoint / MAV Matrix Switchers OperationCrossPoint / MAV Matrix Switchers Operation A B C D EF G H Power Supply LEDs - See pageLit A preset has already been saved to this location Operation, cont’dInput and output buttons 3-4 CrossPoint / MAV Matrix Switchers OperationCrossPoint / MAV Matrix Switchers Operation CrossPoint switchers, Input 1 through 10 Display the RGB delay. SeeOperation, cont’d Control buttonsSave configuration or preset changes that you make on the front panel 3-6 CrossPoint / MAV Matrix Switchers OperationCrossPoint / MAV Matrix Switchers Operation Preset button - The Preset button has two primary functions and threePrimary functions I/O controls3-8 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dWith the RGBHV/Video button, commands the front panel system reset CrossPoint switchers Selects the RGB delay mode, in which you canCrossPoint / MAV Matrix Switchers Operation set the RGB delay. See “Setting RGB delay CrossPoint Switchers” on3-10 CrossPoint / MAV Matrix Switchers Operation Power indicators 2412 and larger models only\⤀Button icons I Primary and Redundant Power Supply LEDsCrossPoint / MAV Matrix Switchers Operation Front Panel OperationsDefinitions Configuration - One or more ties or one or more sets of tiesOperation, cont’d Front panel security lockoutsPower 3-12 CrossPoint / MAV Matrix Switchers OperationCrossPoint / MAV Matrix Switchers Operation Creating a configurationSelect to configure video, audio, or both by pressing the RGBHV CrossPoint switchers or Video MAV Plus switchers button and/or AudioExample 1 Creating a set of video and audio ties 1 2 3 4 5 6 7 8 15 16 17 18 19 20 21 22 23 24 313-14 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dENTER PRESET VIEW The current configuration figure 3-10 is nowFigure 3-10 - Example 1, final configuration CrossPoint / MAV Matrix Switchers Operation1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 83-16 CrossPoint / MAV Matrix Switchers Operation Operation, cont’d4. Press and release the output 1 button figure The current configuration figure 3-16 is nowFigure 3-16 - Example 2, final configuration CrossPoint / MAV Matrix Switchers Operation1 2 3 4 5 6 7 8 3-18 CrossPoint / MAV Matrix Switchers OperationOperation, cont’d 1 2 3 4 5 6 7 8Figure 3-20 - Deselect the output Figure 3-22 - Example 3, final configuration, audio switcherCrossPoint / MAV Matrix Switchers Operation 4. Press and release the output 4 button figureViewing a configuration 3-20 CrossPoint / MAV Matrix Switchers OperationOperation, cont’d Figure 3-23 - Clear all selections 1 2 3 4 5 6 7 8 15CrossPoint / MAV Matrix Switchers Operation Example 4 Viewing video and audio, audio only, and video only ties1 2 3 4 5 6 7 8 3-22 CrossPoint / MAV Matrix Switchers OperationOperation, cont’d 1 2 3 4 5 6 7Figure 3-28 - Press the View button to exit View-only mode CrossPoint / MAV Matrix Switchers Operation1 2 3 4 5 6 7 8 7. Press and release the View button to exit View-only mode figure1 2 3 4 5 6 7 8 9 I/O grouping3-24 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dPress the Enter button to select group Press the Preset button to select groupCrossPoint / MAV Matrix Switchers Operation 3. Press and release one of the Control buttons to select a groupFigure 3-30 - Clear all selections 3-26 CrossPoint / MAV Matrix Switchers OperationOperation, cont’d Example 5 Grouping inputs and outputs1 2 3 4 5 6 7 8 CrossPoint / MAV Matrix Switchers Operation1 2 3 4 5 6 7 8 15 1 2 3 4 5 6 7 8 15Figure 3-36 - Deselect I/O Group mode Setting RGB delay CrossPoint switchers\⤀3-28 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dCrossPoint / MAV Matrix Switchers Operation 22 23 24Example 6 Setting the RGB delay for an output Figure 3-38 - Select RGB Delay modeOperation, cont’d Figure 3-40 - Adjust the RGB delay intervalFigure 3-41 - Deselect RGB Delay mode 3-30 CrossPoint / MAV Matrix Switchers OperationFigure 3-42 - Preset locations by matrix size Using presets10 11 12 13 14 15 17 18 19 20 21 22 23 24 25 26 27 28 29 30 313-32 CrossPoint / MAV Matrix Switchers Operation Example 7 Saving a presetFigure 3-44 - Enter Save Preset mode Figure 3-45 - Select the presetFigure 3-46 - Press the Enter button Example 8 Recalling a presetFigure 3-48 - Enter Recall Preset mode CrossPoint / MAV Matrix Switchers Operationrecall the preset 1 2 3 4 15Figure 3-49 - Select the preset 3-34 CrossPoint / MAV Matrix Switchers OperationPress and release the View button Muting and unmuting video and/or audio outputsCrossPoint / MAV Matrix Switchers Operation Individual outputs can be muted or unmuted as followsExample 9 Muting and unmuting an audio/RS-232 output 3-36 CrossPoint / MAV Matrix Switchers OperationOperation, cont’d 1 2 3 4 5 6 7 8 156. Press and release the View button to exit View-only mode figure CrossPoint / MAV Matrix Switchers OperationFigure 3-53 - Mute the outputs Figure 3-54 - Unmute the outputsFigure 3-56 - Audio gain and attenuation Viewing and adjusting the input audio level audio models\⤀3-38 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dFigure 3-58 - Select Audio mode Example 10 Viewing and adjusting an input audio levelCrossPoint / MAV Matrix Switchers Operation Figure 3-57 - Clear all selectionsCrossPoint 450 Plus Input audio level adjustment displays3-40 CrossPoint / MAV Matrix Switchers Operation Operation, cont’d= Blinking button Input audio level adjustment displaysCrossPoint / MAV Matrix Switchers Operation = Unlit buttonOperation, cont’d Figure 3-60 - Level display on a 16-output-button switcherFigure 3-61 - Level display on a 8-output-button switcher 3-42 CrossPoint / MAV Matrix Switchers OperationCrossPoint / MAV Matrix Switchers Operation Figure 3-62 - Adjust the input audio levelFigure 3-63 - Level display on a 16-output-button switcher Figure 3-64 - Level display on a 8-output-button switcherFigure 3-65 - Deselect Audio mode Viewing and adjusting the output volume audio models\⤀3-44 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dPush Esc button nineteen times more - 10% + 191.5% = 38.5% volume Reading the displayed volumePush Esc button again - 5.5% + 1.5% = 7% volume Push Esc button twice more - 7% + 1.5% + 1.5% = 10% volumeAudio volume adjustment settings 3-46 CrossPoint / MAV Matrix Switchers OperationOperation, cont’d 63 dB of attenuation is applied to the output CrossPoint / MAV Matrix Switchers OperationOperation, cont’d Example 11 Viewing and adjusting an output volume level3-48 CrossPoint / MAV Matrix Switchers Operation PRESETFigure 3-69 - Volume display on a 16-input-button switcher 10 1110 11 13 14 15Operation, cont’d Figure 3-71 - Adjust the output audio volumeFigure 3-72 - Volume display on a 16-input-button switcher 3-50 CrossPoint / MAV Matrix Switchers Operation5. Press and release the Audio button figure CrossPoint / MAV Matrix Switchers OperationFast Blinking Button 26 dB attenuation 61% volume 10 11Selecting Lock mode 2 or toggling between mode 2 and mode Setting the front panel locks Executive modes\⤀3-52 CrossPoint / MAV Matrix Switchers Operation Operation, cont’dSelecting Lock mode 2 or toggling between mode 2 and mode Performing a system reset from the front panelFigure 3-77 - System reset CrossPoint / MAV Matrix Switchers OperationOperation, cont’d Background illuminationSelecting the rear panel Remote port protocol and baud rate 3-54 CrossPoint / MAV Matrix Switchers OperationSee the following table for a summary of the modes Rear Panel OperationsMode 3 turns events on or off. During resetting Reset Mode Comparison/Summary3-56 CrossPoint / MAV Matrix Switchers Operation The switcher reverts to the factory defaultCrossPoint / MAV Matrix Switchers Operation Performing soft system resets resets 3, 4, and 5\⤀Perform a soft reset of the switcher as follows Figure 3-82 - Whole switcher and absolute resetsOperation, cont’d Performing a hard resetFigure 3-83 - Hard reset 3-58 CrossPoint / MAV Matrix Switchers OperationGeneral checks TroubleshootingPlasma display S-video problem CrossPoint switchers\⤀ Optimizing the Audio Audio Models\⤀Operation, cont’d Configuration WorksheetsWorksheet example 1 System equipment 3-60 CrossPoint / MAV Matrix Switchers OperationWorksheet example 2 Daily configuration Figure 3-85 - Worksheet example 2 Daily configurationCrossPoint / MAV Matrix Switchers Operation Operation, cont’d Worksheet example 3 Test configurationFigure 3-86 - Worksheet example 3 Test configuration 3-62 CrossPoint / MAV Matrix Switchers OperationInput sources 32-button switchers configuration worksheetCrossPoint / MAV Matrix Switchers Operation Preset #Operation, cont’d 3-64 CrossPoint / MAV Matrix Switchers OperationInput sources 16-button switchers configuration worksheetCrossPoint / MAV Matrix Switchers Operation Preset #Operation, cont’d 3-66 CrossPoint / MAV Matrix Switchers OperationChapter4Four Serial Ports Ethernet LAN\⤀ Port Host-to-Switcher InstructionsSwitcher-Initiated Messages Switcher Error Responses Using the Command/Response TablesFigure 4-1 - Remote connector pin assignments Programmer’s GuideSerial Ports Rear panel Remote portFront panel Configuration port CrossPoint / MAV Matrix Switchers Programmer’s GuideFigure 4-2 - Optional 9-pin TRS RS-232 cable Figure 4-3 - RJ-45 Ethernet connector pin assignments Programmer’s Guide, cont’dEthernet LAN\⤀ Port Ethernet connectionNumber of connections Default IP addressesConnection Timeouts Establishing a connection4-6 CrossPoint / MAV Matrix Switchers Programmer’s Guide Host-to-Switcher InstructionsSwitcher-Initiated Messages Verbose ModeCrossPoint / MAV Matrix Switchers Programmer’s Guide Switcher Error ResponsesUsing the Command/Response Tables 4-8 CrossPoint / MAV Matrix Switchers Programmer’s GuideProgrammer’s Guide, cont’d Page Command/response table for SIS commands 4-10 CrossPoint / MAV Matrix Switchers Programmer’s GuideProgrammer’s Guide, cont’d CrossPoint / MAV Matrix Switchers Programmer’s Guide Command/response table for SIS commands continued\⤀Command ASCII command4-12 CrossPoint / MAV Matrix Switchers Programmer’s Guide Command/response table for SIS commands continued\⤀Command ASCII commandCrossPoint / MAV Matrix Switchers Programmer’s Guide Command/response table for SIS commands continued\⤀Command ASCII command4-14 CrossPoint / MAV Matrix Switchers Programmer’s Guide Command/response table for SIS commands continued\⤀Command ASCII commandCommand/response table for SIS commands continued\⤀ View ties, gain, volume, mutes, presets, and DSVPMAV Plus 4-16 CrossPoint / MAV Matrix Switchers Programmer’s Guide Command/response table for SIS commands continued\⤀Command ASCII commandASCII command X1# X1#Command/response table for SIS commands continued\⤀ CommandNames Command/response table for SIS commands continuedProgrammer’s Guide, cont’d I/O Grouping continuedCommand/response table for SIS commands continued\⤀ ResetsLock executive\⤀ modes 4-20 CrossPoint / MAV Matrix Switchers Programmer’s Guide Command/response table for SIS commands continued\⤀Command ASCII commandCrossPoint / MAV Matrix Switchers Programmer’s Guide Command/response table for SIS commands continued\⤀Command ASCII commandCommand/Response Table for IP-specific SIS Commands Symbol definitionsProgrammer’s Guide, cont’d X5 X5 X5 CrossPoint / MAV Matrix Switchers Programmer’s GuideCommand/response table for IP-specific SIS commands IP setup commandsProgrammer’s Guide, cont’d IP setup commands continued\⤀ Command/response table for IP-specific SIS commands continued\⤀Special Characters 4-26 CrossPoint / MAV Matrix Switchers Programmer’s GuideProgrammer’s Guide, cont’d Button Label Generator Program Matrix Switchers Control Program Special CharactersChapter5Five Matrix SoftwareThe Matrix Switchers Control Program The Firmware Loader Matrix Switchers Control ProgramInstalling the software Matrix SoftwareSoftware operation via Ethernet Ethernet protocol settingsCrossPoint / MAV Matrix Switchers Matrix Software 5-4 CrossPoint / MAV Matrix Switchers Matrix Software Using the Matrix Switcher Control softwareMatrix Software, cont’d Figure 5-4 - Address and password entryFigure 5-5 - Extron Matrix Switchers Control Program window blank CrossPoint / MAV Matrix Switchers Matrix SoftwareIf the IP address is correct Proceed to step 3b 5-6 CrossPoint / MAV Matrix Switchers Matrix Software Matrix Software, cont’dFigure 5-6 - Sample program window complete Matrix IP Address field IP Settings/Options windowFigure 5-7 - Control program IP setting/options window CrossPoint / MAV Matrix Switchers Matrix SoftwareAddress field 5-8 CrossPoint / MAV Matrix Switchers Matrix SoftwareMatrix Software, cont’d Edit the address as desiredMask field CrossPoint / MAV Matrix Switchers Matrix SoftwareSubnet Mask field Edit the mask as desiredSync Time to PC button Administrator Password field5-10 CrossPoint / MAV Matrix Switchers Matrix Software Matrix Software, cont’dcursor User Password fieldCrossPoint / MAV Matrix Switchers Matrix Software Mail Server IP Address fieldE-mail Addressee fields 5-12 CrossPoint / MAV Matrix Switchers Matrix SoftwareMatrix Software, cont’d Miles StandishUpdating firmware Figure 5-9 - Location of firmware upgrade filesCrossPoint / MAV Matrix Switchers Matrix Software Folder where firmware is installed Figure 5-10 - Downloading firmware upgrade filesfolder identified in the InstallShield Wizard window 5-14 CrossPoint / MAV Matrix Switchers Matrix SoftwareCrossPoint / MAV Matrix Switchers Matrix Software switcher LAN port. See chapter 2, “Installation”, for more detailsStart the Matrix Switchers Control Program and connect to the Click Tools Update FirmwareFigure 5-12 - Firmware loading 5-16 CrossPoint / MAV Matrix Switchers Matrix SoftwareMatrix Software, cont’d Serial-port-connected firmware upload13. If necessary, change the port number in the device port field Front panel Configuration port, enterCrossPoint / MAV Matrix Switchers Matrix Software Figure 5-13 - Confirm windowFigure 5-14 - HTML Files List window Uploading HTML files5-18 CrossPoint / MAV Matrix Switchers Matrix Software Matrix Software, cont’dCrossPoint / MAV Matrix Switchers Matrix Software Windows buttons, drop boxes, and trashcanWindows menus Exit - Closes the Matrix Switchers Control Program5-20 CrossPoint / MAV Matrix Switchers Matrix Software Matrix Software, cont’dTools menu Figure 5-15 - Status window Audio-input Configuration selectionCrossPoint / MAV Matrix Switchers Matrix Software White - Not displayed for the CrossPoint or MAVFigure 5-16 - Ties shown as lines 5-22 CrossPoint / MAV Matrix Switchers Matrix SoftwareMatrix Software, cont’d Preferences menuSwitcher + Control Pgm Using Emulation modeUsing the help system Master-Reset selectionSpecial Characters Button-Label Generator Program5-24 CrossPoint / MAV Matrix Switchers Matrix Software Matrix Software, cont’dUsing the Button-Label Generator software CrossPoint / MAV Matrix Switchers Matrix SoftwareFigure 5-19 - Extron’s Button-Label Generator window Matrix Software, cont’d 5-26 CrossPoint / MAV Matrix Switchers Matrix SoftwareFile Management Tab Control Tab Special Characters Download the Startup Page Status Tab Configuration TabChapter6Six HTML OperationStart the Web browser program HTML OperationDownload the Startup Page 6-2 CrossPoint / MAV Matrix Switchers HTML OperationFigure 6-2 - System Status page Status TabSystem Status page CrossPoint / MAV Matrix Switchers HTML OperationFigure 6-3 - DSVP page DSVP page CrossPoint switchers\⤀HTML Operation, cont’d 6-4 CrossPoint / MAV Matrix Switchers HTML OperationCrossPoint / MAV Matrix Switchers HTML Operation Configuration TabSystem Settings Page Figure 6-4 - System Settings pageUnit Name field IP Settings fields6-6 CrossPoint / MAV Matrix Switchers HTML Operation HTML Operation, cont’dyear, hours, minutes, AM/PM, and time zone. A drop-down scroll box Date/Time Settings fieldsFigure 6-5 - Date/Time Settings fields CrossPoint / MAV Matrix Switchers HTML OperationHTML Operation, cont’d Passwords pageFigure 6-6 - Passwords page 6-8 CrossPoint / MAV Matrix Switchers HTML OperationMail IP Address field Email Settings pageFigure 6-7 - Email Settings page CrossPoint / MAV Matrix Switchers HTML OperationHTML Operation, cont’d Firmware Upgrade pageFigure 6-8 - Firmware Upgrade page 6-10 CrossPoint / MAV Matrix Switchers HTML OperationCrossPoint / MAV Matrix Switchers HTML Operation File Management TabFile Management Page Click the Firmware Upgrade linkHTML Operation, cont’d Control TabUser Control Page 6-12 CrossPoint / MAV Matrix Switchers HTML OperationCreating or deleting a tie RGB and Audio Settings pageFigure 6-11 - RGB and Audio Settings page CrossPoint / MAV Matrix Switchers HTML OperationFigure 6-12 - Input selection drop box 6-14 CrossPoint / MAV Matrix Switchers HTML OperationHTML Operation, cont’d Change the input gain and attenuation audio models\⤀Figure 6-14 - Output selection drop box CrossPoint / MAV Matrix Switchers HTML OperationMute and unmute one or all outputs Mute one or all outputs as followsHTML Operation, cont’d Change the RGB delay CrossPoint switchers\⤀Figure 6-17 - RGB delay drop box 6-16 CrossPoint / MAV Matrix Switchers HTML OperationFigure 6-18 - Output selection drop box Change the output volume level audio models\⤀Figure 6-19 - Volume drop box CrossPoint / MAV Matrix Switchers HTML OperationAudio volume adjustment settings 6-18 CrossPoint / MAV Matrix Switchers HTML OperationHTML Operation, cont’d Save the current configuration configuration 0 as a preset as follows Global Presets pageFigure 6-20 - Global Presets page Saving a presetSpecial Characters Recalling a preset6-20 CrossPoint / MAV Matrix Switchers HTML Operation HTML Operation, cont’dCrossPoint / MAV Matrix Switchers AAppendix AEthernet Connection Ethernet Link Subnetting - A PrimerFigure A-1 - RJ-45 connector pinout tables Default addressEthernet Connection Ethernet LinkFigure A-2 - Ping response Connecting as a Telnet clientCrossPoint / MAV Matrix Switchers Ethernet Connection Pinging to determine Extron IP addressTelnet tips Ethernet Connection, cont’dA-4 CrossPoint / MAV Matrix Switchers Ethernet Connection Figure A-3 - Telnet screenClose CrossPoint / MAV Matrix Switchers Ethernet ConnectionLocal echo Set carriage return-line feedIP addresses and octets Subnetting - A PrimerGateways Local and remote devicesMasked octets are not compared indicated by X in figure A-6 Determining whether devices are on the same subnetCrossPoint / MAV Matrix Switchers Ethernet Connection Unmasked octets are compared indicated by ? in figure A-6Ethernet Connection, cont’d A-8 CrossPoint / MAV Matrix Switchers Ethernet ConnectionReference Information CrossPoint 450 Plus Specifications CrossPoint Ultra SpecificationsMAV Plus Specifications Part Numbers and Accessories Button Labels AppendixBBVideo input CrossPoint 450 Plus SpecificationsReference Information VideoAudio output - audio models only SyncAudio - audio models only Audio input - audio models onlyB-4 CrossPoint / MAV Matrix Switchers Reference Information Control/remote - switcherReference Information, cont’d GeneralVideo input CrossPoint Ultra SpecificationsCrossPoint / MAV Matrix Switchers Reference Information VideoVideo output Audio- audio models onlyB-6 CrossPoint / MAV Matrix Switchers Reference Information Reference Information, cont’dCrossPoint / MAV Matrix Switchers Reference Information Audio input- audio models onlyAudio output- audio models only Control/remote - switcherN All nominal levels are at ±10% B-8 CrossPoint / MAV Matrix Switchers Reference InformationReference Information, cont’d GeneralCrossPoint / MAV Matrix Switchers Reference Information MAV Plus SpecificationsVideo - video models Video input - video modelsB-10 CrossPoint / MAV Matrix Switchers Reference Information Video output - video modelsSync - MAV Plus 88/128/1212/168/816/1616 video models Sync - MAV Plus 2412/2424/3216/3232 video modelsAudio - audio models Audio input - audio modelsCrossPoint / MAV Matrix Switchers Reference Information B-11 Reference Information, cont’d Audio output - audio modelsControl/remote - switcher B-12 CrossPoint / MAV Matrix Switchers Reference Information3216 Series CrossPoint / MAV Matrix Switchers Reference Information B-13N All nominal levels are at ±10% 2412 SeriesMatrix switcher part numbers Part Numbers and AccessoriesCrossPoint 450 Plus matrix switcher part numbers CrossPoint Ultra matrix switcher part numbersPart number MAV Plus matrix switcher part numbersMAV Plus matrix switcher part numbers CrossPoint / MAV Matrix Switchers Reference Information B-15Part number MAV Plus matrix switcher part numbersB-16 CrossPoint / MAV Matrix Switchers Reference Information Reference Information, cont’dAccessory Replacement partsOptional accessories Included partsRG59/high resolution cable CablesAccessory RG6/super high resolution cableRG59/high resolution cable Pre-cut cablesPlenum BNC-5 mini high resolution cable Assorted connectorsB-20 CrossPoint / MAV Matrix Switchers Reference Information Installing labels in the matrix switcher’s buttonsButton Labels Figure B-1 - Illuminated button label replacementButton label blanks, 16-button strips CrossPoint / MAV Matrix Switchers Reference Information B-21Reference Information, cont’d B-22 CrossPoint / MAV Matrix Switchers Reference Informationand Central America Extron’s WarrantyUSA, Canada, South America Europe, Africa, and the Middle EastExtron Electronics, Europe Beeldschermweg 6C