Manuals / Frymaster / Kitchen Appliance / Fryer

Frymaster H52 Series warranty How to Change Computer Product/Temperature Displays

Models: H52 Series

1 48

Download 48 pages 48.78 Kb

Page 22

How to Change Computer Product/Temperature Displays

4.Press the switch to save the settings.

5.Press either ON/OFF switch to save the setting and exit the setup mode. Both displays will change to OFF.

How to Configure the Computer for Use on Either a Full-Vat or a Split-Vat Fryer

1.Enter the setup mode. See How to Enter the Setup Mode on Page 3-8.

2.Press and release the switch until 1 vat appears in the left display.

3.Press the right 1 or 2 switch to toggle back and forth between full-vat (yes) or split-vat (NO).

4.Press the switch to save the settings.

5.Press either ON/OFF switch to exit the setup mode. Both displays will change to OFF.

How to Change Computer Product/Temperature Displays

1.Enter the setup mode. See How to Enter the Setup Mode on Page 3-8.

2.Press and release the switch until the word DISPLAY appears in the left display.

3.Press the right 1 or 2 switch to toggle back and forth between constant product display (CONSTANT) or alternating temperature and product display (ALT).

4.Press the switch to save the settings.

5.Press either ON/OFF switch to exit the setup mode. Both displays will change to OFF.

How to Calibrate Computer Temperature to Actual Frypot Temperature

NOTE: For this procedure, actual frypot temperature refers to the temperature of the oil in the frypot as measured with a good-grade thermometer or pyrometer. The computer’s temperature can only be adjusted ±5°F (±3°C). The computer cannot be adjusted to a temperature greater than 375°F (191°C).

1.Enter the setup mode. See How to Enter the Setup Mode on Page 3-8.

2.Press and release the switch until CALIB appears in the display.

3.Press the temperature check switch . The frypot temperature sensed by the computer will be displayed. In split-vat units, the temperatures for each side will be displayed.

4.For the left side of a split-vat: Press the left Fahrenheit or 3 for Celsius). Press the left 2 Fahrenheit or 3 for Celsius).

1switch to go UP a degree (maximum of 5 for switch to go DOWN a degree (maximum of 5 for

3–9

Image 22

Frymaster H52 Series warranty How to Change Computer Product/Temperature Displays

Contents

FOR YOUR SAFETY OPERATOR’S MANUAL FRYMASTER H52 SERIES GAS FRYERTABLE OF CONTENTS SERVICE HOTLINEPage Example of a CAUTION box CHAPTER 1 INTRODUCTION1.1 General Example of a WARNING box1.4 European Community CE Specific Information Non-CE specific information 1.5 Shipping Damage Claim Procedure1.3 Computer Information CE Standard Example of box used to distinguish CE and1.6 Service Information RETAIN AND STORE THIS MANUAL IN A SAFE PLACE FOR FUTURE USECLEARANCE AND VENTILATION CHAPTER 2 INSTALLATION INSTRUCTIONS2.1 General Installation Requirements DANGERNATIONAL CODE REQUIREMENTS This equipment requires electrical power for operationDo not attempt to use the equipment during a power outage ELECTRICAL GROUNDING REQUIREMENTSDo not connect fryer to gas supply before completing each step 2.2 Caster/Leg Installation2.3 Pre-Connection Preparations DANGER in this sectionfor Fryers Manufactured Through April CE Standard for Incoming Gas Pressuresfor Fryers Manufactured After April Non-CE Standard for Incoming Gas Pressures2.4 Connection to Gas Line H152-2 units are not approved for G30 Butane gasIf gas odors are detected, shut off the gas supply to the fryer service agency for serviceCE Standard Required airflow for the combustion air supply is 2m3/h per kW4. It is suggested that the burner manifold pressure be checked at this time by the local gas com- pany or an authorized service agent. Refer to “Check Burner Manifold Pressure” in Chapter 5 of this manual for the proper procedure. The accompanying tables list the burner manifold gas pressures for the various gas types that can be used with this equipment 2.5 Converting to Another Gas TypeDANGER CE GAS CONVERSION INSTRUCTIONS Non-CE Gas Conversion KitsCE Gas Conversion Kits for Units with Gas Valve 2.6 Frypot Boil-OutShutdown 3.1 Equipment Setup and Shutdown Procedures SetupCHAPTER 3 OPERATING FRYERS WITH M100B COOKING COMPUTERS 3.2 Finding Information3.3 Introduction To The M-100B Cooking Computer DESCRIPTIONproperly filled with vegetable oil. See Section 3.4 M-100B Computer Operating InstructionsOperating the Computer on Full-Vat Fryers Operating the Computer on Split-Vat Fryers Viewing the Frypot Temperature Actual or SetpointCooking Product Full-Vat or Split-Vat 3.5 M-100B Computer Problem Condition Indicators Recovery Out of Range REC LOCKLow Temperature Indication Open Drain Valve Indication3.6 M-100B Computer Set-Up and Programming Instructions In the Setup Mode, the operator canProbe Failure Indication In the Program Mode, the operator canHow to Change the Computer’s Display Language 3.6.1 M-100B Computer Setup ModeHow to Enter the Setup Mode How to Configure the Computer for Use on a Gas FryerHow to Change Computer Product/Temperature Displays How to Calibrate Computer Temperature to Actual Frypot TemperatureHow to Reset the Computer to the Factory Defaults How to Activate or Deactivate the Frypot BOIL-OUT FeatureHow to Enter the Program Mode How to Change the Shake, Pull, Or Quality Times for Menu ItemsHow to Change the Cooking Temperature Setpoint How to Enter a Product Name in a Test Menu How to Suppress a Shake, QA, or Duty Function How to Display “Use Time” Information How to Turn the Display of a Factory-Programmed Menu Item On and OffHow to Display the Product Cycle Accumulator Information How to Use the Filter Countdown Timer CHAPTER 4 OPERATING FRYERS WITH ANALOG CONTROLLERS 4.1 Equipment Setup and Shutdown Procedures Setupswitch to the ON position. Failure to do so could damage the frypot 4.2 Introduction to the Analog ControllerDESCRIPTION A B C D E F G H I J K L M N4.4 Analog Controller High-Limit Check control-check procedure4.3 Analog Controller Operating Instructions properly filled with vegetable oil. See Sectionrelease switch 5.1 Draining and Manual Filtering DANGER Always wear appropriate protective gloves when draining or filteringCHAPTER 5 FILTERING container for disposal1. Turn the controller OFF 5.2 Operating the Built-In Filtration SystemPREPARING THE FILTER UNIT FOR USE and CHANGING THE FILTER PAPER DANGERIf using the optional filter pad, place the ring over the pad NOTE! DO NOT use filter powder if using the optional filter padOPERATING THE FILTER UNIT to cooking temperaturetemperature probe or operating thermostat Hot oil will rush out, creating an extreme hazardPage 5.3 Getting the Most Out of Your Filter g. Insert filter pan into the filter base assembly 6.2 Troubleshooting CHAPTER 6 PREVENTIVE MAINTENANCE AND TROUBLESHOOTING6.1 Preventive Maintenance Verify that electrical cords are securely plugged in6.2.1 Troubleshooting Fryers with M100B Computers REC LOCKIGNITION FAILURE If problem repeatsIGNITION FAILURE computer on anotheroperating will not enter programming6.2.3 Troubleshooting Fryers Equipped with Analog Controllers BURNERS DO NOT LIGHT POWER LIGHT ON HEAT LIGHT ON TROUBLE LIGHT ON 6.2.4 Troubleshooting Built-in Filtration System for a while and then thermal overload resetpump microswitch, a failed pump relay stopped?